PREN 14308 : DRAFT 2015

Add To Cart

Sorry this product is not available in your region.

Table of Contents - (Show below) - (Hide below)

Foreword
1 Scope
2 Normative references
3 Terms, definitions, symbols, units and abbreviated
  terms
4 Requirements
5 Test methods
6 Designation code
7 Assessment and Verification of the Constancy of
  Performance (AVCP)
8 Marking and labelling
Annex A (normative) - Factory production control
Annex B (normative) - Determination of minimum
        service temperature
Annex C (normative) - Determination of the aged value
        of thermal conductivity and thermal resistance
Annex D (informative) - Additional properties
Annex ZA (informative) - Clauses of this European Standard
         addressing the provisions of the EU Construction
         Products Regulation
Bibliography

Abstract - (Show below) - (Hide below)

Provides the requirements for factory made rigid polyurethane foam (PUR) and polyisocyanurate foam (PIR) products, with a closed cell content not less than 90%, with or without facings, which are used for the thermal insulation of building equipment and industrial installations, with an operating temperature range of approximately, - 200 degrees C to + 200 degrees C.

General Product Information - (Show below) - (Hide below)

Published
Document Type	Draft
Status	Superseded
Publisher	Comite Europeen de Normalisation
Pages
ISBN
Committee	TC 88
Superseded By	EN 14308 : 2015
Comment Closes On

National Adoptions - (Show below) - (Hide below)

Equivalent Standard(s)	Relationship
15/30315081 DC : DRAFT MAY 2015	Identical
05/30136516 DC : 0	Identical
15/30315081 DC : DRAFT MAY 2015	Identical

Standards Referencing This Book - (Show below) - (Hide below)

ISO 9229 : 2007(R2012)	THERMAL INSULATION - VOCABULARY
EN 12667 : 2001	THERMAL PERFORMANCE OF BUILDING MATERIALS AND PRODUCTS - DETERMINATION OF THERMAL RESISTANCE BY MEANS OF GUARDED HOT PLATE AND HEAT FLOW METER METHODS - PRODUCTS OF HIGH AND MEDIUM THERMAL RESISTANCE
ISO 13787 : 2003(R2014)	THERMAL INSULATION PRODUCTS FOR BUILDING EQUIPMENT AND INDUSTRIAL INSTALLATIONS - DETERMINATION OF DECLARED THERMAL CONDUCTIVITY
EN 14706 : 2012	THERMAL INSULATING PRODUCTS FOR BUILDING EQUIPMENT AND INDUSTRIAL INSTALLATIONS - DETERMINATION OF MAXIMUM SERVICE TEMPERATURE
EN 13468 : 2001	THERMAL INSULATING PRODUCTS FOR BUILDING EQUIPMENT AND INDUSTRIAL INSTALLATIONS - DETERMINATION OF TRACE QUANTITIES OF WATER SOLUBLE CHLORIDE, FLUORIDE, SILICATE, SODIUM IONS AND PH
EN ISO 10456 : 2007 COR 2009	BUILDING MATERIALS AND PRODUCTS - HYGROTHERMAL PROPERTIES - TABULATED DESIGN VALUES AND PROCEDURES FOR DETERMINING DECLARED AND DESIGN THERMAL VALUES
EN 1607 : 2013	THERMAL INSULATING PRODUCTS FOR BUILDING APPLICATIONS - DETERMINATION OF TENSILE STRENGTH PERPENDICULAR TO FACES
EN 1606 : 2013	THERMAL INSULATING PRODUCTS FOR BUILDING APPLICATIONS - DETERMINATION OF COMPRESSIVE CREEP
EN 13471 : 2001	THERMAL INSULATING PRODUCTS FOR BUILDING EQUIPMENT AND INDUSTRIAL INSTALLATIONS - DETERMINATION OF THE COEFFICIENT OF THERMAL EXPANSION
EN 12939 : 2000	THERMAL PERFORMANCE OF BUILDING MATERIALS AND PRODUCTS - DETERMINATION OF THERMAL RESISTANCE BY MEANS OF GUARDED HOT PLATE AND HEAT FLOW METER METHODS - THICK PRODUCTS OF HIGH AND MEDIUM THERMAL RESISTANCE
EN ISO 8497 : 1996	THERMAL INSULATION - DETERMINATION OF STEADY-STATE THERMAL TRANSMISSION PROPERTIES OF THERMAL INSULATION FOR CIRCULAR PIPES
EN 13501-1 : 2007 + A1 2009	FIRE CLASSIFICATION OF CONSTRUCTION PRODUCTS AND BUILDING ELEMENTS - PART 1: CLASSIFICATION USING DATA FROM REACTION TO FIRE TESTS
EN ISO 9229 : 2007	THERMAL INSULATION - VOCABULARY
EN ISO 4590 : 2016	RIGID CELLULAR PLASTICS - DETERMINATION OF THE VOLUME PERCENTAGE OF OPEN CELLS AND OF CLOSED CELLS (ISO 4590:2016)
EN 13469 : 2012	THERMAL INSULATING PRODUCTS FOR BUILDING EQUIPMENT AND INDUSTRIAL INSTALLATIONS - DETERMINATION OF WATER VAPOUR TRANSMISSION PROPERTIES OF PREFORMED PIPE INSULATION
ASTM D 3985 : 2005	TEST METHOD FOR OXYGEN GAS TRANSMISSION RATE THROUGH PLASTIC FILM AND SHEETING USING A COULOMETRIC SENSOR
EN 824 : 2013	THERMAL INSULATING PRODUCTS FOR BUILDING APPLICATIONS - DETERMINATION OF SQUARENESS
ISO 4590 : 2016	RIGID CELLULAR PLASTICS - DETERMINATION OF THE VOLUME PERCENTAGE OF OPEN CELLS AND OF CLOSED CELLS
ISO 11925-2 : 2010	REACTION TO FIRE TESTS - IGNITABILITY OF PRODUCTS SUBJECTED TO DIRECT IMPINGEMENT OF FLAME - PART 2: SINGLE-FLAME SOURCE TEST
EN 825 : 2013	THERMAL INSULATING PRODUCTS FOR BUILDING APPLICATIONS - DETERMINATION OF FLATNESS
EN 823 : 2013	THERMAL INSULATING PRODUCTS FOR BUILDING APPLICATIONS - DETERMINATION OF THICKNESS
ISO 8497 : 1994(R2013)	THERMAL INSULATION - DETERMINATION OF STEADY-STATE THERMAL TRANSMISSION PROPERTIES OF THERMAL INSULATION FOR CIRCULAR PIPES
EN ISO 13787 : 2003	THERMAL INSULATION PRODUCTS FOR BUILDING EQUIPMENT AND INDUSTRIAL INSTALLATIONS - DETERMINATION OF DECLARED THERMAL CONDUCTIVITY
EN 13470 : 2001	THERMAL INSULATING PRODUCTS FOR BUILDING EQUIPMENT AND INDUSTRIAL INSTALLATIONS - DETERMINATION OF THE APPARENT DENSITY OF PREFORMED PIPE INSULATION
EN 13238 : 2010	REACTION TO FIRE TESTS FOR BUILDING PRODUCTS - CONDITIONING PROCEDURES AND GENERAL RULES FOR SELECTION OF SUBSTRATES
EN 13823 : 2010 + A1 2014	REACTION TO FIRE TESTS FOR BUILDING PRODUCTS - BUILDING PRODUCTS EXCLUDING FLOORINGS EXPOSED TO THE THERMAL ATTACK BY A SINGLE BURNING ITEM
EN 1602 : 2013	THERMAL INSULATING PRODUCTS FOR BUILDING APPLICATIONS - DETERMINATION OF THE APPARENT DENSITY
EN 12090 : 2013	THERMAL INSULATING PRODUCTS FOR BUILDING APPLICATIONS - DETERMINATION OF SHEAR BEHAVIOUR
EN 1604 : 2013	THERMAL INSULATING PRODUCTS FOR BUILDING APPLICATIONS - DETERMINATION OF DIMENSIONAL STABILITY UNDER SPECIFIED TEMPERATURE AND HUMIDITY CONDITIONS
EN 14707 : 2012	THERMAL INSULATING PRODUCTS FOR BUILDING EQUIPMENT AND INDUSTRIAL INSTALLATIONS - DETERMINATION OF MAXIMUM SERVICE TEMPERATURE FOR PREFORMED PIPE INSULATION
EN 13165 : 2012 + A2 2016	THERMAL INSULATION PRODUCTS FOR BUILDINGS - FACTORY MADE RIGID POLYURETHANE FOAM (PU) PRODUCTS - SPECIFICATION
EN 12089 : 2013	THERMAL INSULATING PRODUCTS FOR BUILDING APPLICATIONS - DETERMINATION OF BENDING BEHAVIOUR
ISO 10456 : 2007(R2017)	BUILDING MATERIALS AND PRODUCTS - HYGROTHERMAL PROPERTIES - TABULATED DESIGN VALUES AND PROCEDURES FOR DETERMINING DECLARED AND DESIGN THERMAL VALUES
EN 12429 : 1998	THERMAL INSULATING PRODUCTS FOR BUILDING APPLICATIONS - CONDITIONING TO MOISTURE EQUILIBRIUM UNDER SPECIFIED TEMPERATURE AND HUMIDITY CONDITIONS
EN 1609 : 2013	THERMAL INSULATING PRODUCTS FOR BUILDING APPLICATIONS - DETERMINATION OF SHORT TERM WATER ABSORPTION BY PARTIAL IMMERSION
EN 826 : 2013	THERMAL INSULATING PRODUCTS FOR BUILDING APPLICATIONS - DETERMINATION OF COMPRESSION BEHAVIOUR
EN 15715 : 2009	THERMAL INSULATION PRODUCTS - INSTRUCTIONS FOR MOUNTING AND FIXING FOR REACTION TO FIRE TESTING - FACTORY MADE PRODUCTS
EN ISO 11925-2 : 2010 COR 2011	REACTION TO FIRE TESTS - IGNITABILITY OF PRODUCTS SUBJECTED TO DIRECT IMPINGEMENT OF FLAME - PART 2: SINGLE-FLAME SOURCE TEST
EN 12086 : 2013	THERMAL INSULATING PRODUCTS FOR BUILDING APPLICATIONS - DETERMINATION OF WATER VAPOUR TRANSMISSION PROPERTIES
EN 13172 : 2012	THERMAL INSULATING PRODUCTS - EVALUATION OF CONFORMITY
EN 822 : 2013	THERMAL INSULATING PRODUCTS FOR BUILDING APPLICATIONS - DETERMINATION OF LENGTH AND WIDTH

Publisher