• 17/30339707 DC : 0

    NA Status of Standard is Unknown
    Add to Watchlist
    This Standard has been added successfully to your Watchlist.
    Please visit My Watchlist to see all standards that you are watching.
    Please log in or to add this standard to your Watchlist.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    You have already added this standard to your Watchlist.
    Visit My Watchlist to view the full list.

    BS ISO 21138-2 - PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - STRUCTURED-WALL PIPING SYSTEMS OF UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U), POLYPROPYLENE (PP) AND POLYETHYLENE (PE) - PART 2: PIPES AND FITTINGS WITH SMOOTH EXTERNAL SURFACE, TYPE A

    Available format(s):  Hardcopy, PDF

    Language(s):  English

    Published date: 

    Publisher:  British Standards Institution

    Add to Watchlist

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Foreword
    Introduction
    1 Scope
    2 Normative references
    3 Terms, definitions, symbols and abbreviated
       terms
    4 Material
    5 Designation of wall construction and examples
       of typical jointing methods
    6 General characteristics for pipes and
       fittings - Colour
    7 Geometrical characteristics
    8 Physical characteristics
    9 Mechanical characteristics
    10 Performance requirements
    11 Marking
    Annex A (normative) - Virgin PVC-U material
    Annex B (normative) - Utilization of non-virgin
            PVC-U material
    Annex C (normative) - Virgin PP material
    Annex D (normative) - Utilization of non-virgin
            PP material
    Annex E (normative) - Virgin PE material
    Annex F (normative) - Utilization of non-virgin
            PE material
    Annex G (informative) - Survey of possible use of
            reprocessed and recycled material
    Annex H (normative) - Design of pipes for installation
            deeper than 6m

    General Product Information - (Show below) - (Hide below)

    Comment Closes On
    Committee PRI/88/1
    Document Type Draft
    Publisher British Standards Institution
    Status NA

    Standards Referencing This Book - (Show below) - (Hide below)

    ISO 580:2005 Plastics piping and ducting systems Injection-moulded thermoplastics fittings Methods for visually assessing the effects of heating
    EN 681-4:2000/A2:2005 ELASTOMERIC SEALS - MATERIALS REQUIREMENTS FOR PIPE JOINT SEALS USED IN WATER AND DRAINAGE APPLICATIONS - PART 4: CAST POLYURETHANE SEALING ELEMENTS
    ISO 2507-2:1995 Thermoplastics pipes and fittings Vicat softening temperature Part 2: Test conditions for unplasticized poly(vinyl chloride) (PVC-U) or chlorinated poly(vinyl chloride) (PVC-C) pipes and fittings and for high impact resistance poly (vinyl chloride) (PVC-HI) pipes
    ISO 13259:2010 Thermoplastics piping systems for underground non-pressure applications Test method for leaktightness of elastomeric sealing ring type joints
    ISO 3451-1:2008 Plastics Determination of ash Part 1: General methods
    ISO 13229:2010 Thermoplastics piping systems for non-pressure applications Unplasticized poly(vinyl chloride) (PVC-U) pipes and fittings Determination of the viscosity number and K-value
    EN 681-1:1996/A3:2005 ELASTOMERIC SEALS - MATERIALS REQUIREMENTS FOR PIPE JOINT SEALS USED IN WATER AND DRAINAGE APPLICATIONS - PART 1: VULCANIZED RUBBER
    ISO 8773:2006 Plastics piping systems for non-pressure underground drainage and sewerage Polypropylene (PP)
    ISO 1167-2:2006 Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 2: Preparation of pipe test pieces
    EN 15345 : 2007 PLASTICS - RECYCLED PLASTICS - CHARACTERISATION OF POLYPROPYLENE (PP) RECYCLATES
    ISO 8772:2006 Plastics piping systems for non-pressure underground drainage and sewerage Polyethylene (PE)
    ISO 1133-1:2011 Plastics Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics Part 1: Standard method
    ISO 11173:1994 Thermoplastics pipes Determination of resistance to external blows Staircase method
    ISO 2507-1:1995 Thermoplastics pipes and fittings Vicat softening temperature Part 1: General test method
    ISO 13265:2010 Thermoplastics piping systems for non-pressure underground drainage and sewerage Joints for buried non-pressure applications Test method for the long-term sealing performance of joints with elastomeric seals by estimating the sealing pressure
    ISO 3127:1994 Thermoplastics pipes Determination of resistance to external blows Round-the-clock method
    EN 15346:2014 PLASTICS - RECYCLED PLASTICS - CHARACTERIZATION OF POLY(VINYL CHLORIDE) (PVC) RECYCLATES
    ISO 13968:2008 Plastics piping and ducting systems Thermoplastics pipes Determination of ring flexibility
    ISO 161-1:1996 Thermoplastics pipes for the conveyance of fluids Nominal outside diameters and nominal pressures Part 1: Metric series
    EN 681-2:2000/A2:2005 ELASTOMERIC SEALS - MATERIALS REQUIREMENTS FOR PIPE JOINT SEALS USED IN WATER AND DRAINAGE APPLICATIONS - PART 2: THERMOPLASTIC ELASTOMERS
    ISO 527-2:2012 Plastics Determination of tensile properties Part 2: Test conditions for moulding and extrusion plastics
    ISO 3126:2005 Plastics piping systems Plastics components Determination of dimensions
    ISO 13260:2010 Thermoplastics piping systems for non-pressure underground drainage and sewerage Test method for resistance to combined temperature cycling and external loading
    ISO 13262:2010 Thermoplastics piping systems for non-pressure underground drainage and sewerage Thermoplastics spirally-formed structured-wall pipes Determination of the tensile strength of a seam
    ISO 22088-3:2006 Plastics Determination of resistance to environmental stress cracking (ESC) Part 3: Bent strip method
    ISO 1158:1998 Plastics Vinyl chloride homopolymers and copolymers Determination of chlorine content
    ISO 1183-1:2012 Plastics Methods for determining the density of non-cellular plastics Part 1: Immersion method, liquid pyknometer method and titration method
    EN 10204 : 2004 METALLIC PRODUCTS - TYPES OF INSPECTION DOCUMENTS
    ISO 9001:2015 Quality management systems - Requirements
    ISO 11357-6:2008 Plastics Differential scanning calorimetry (DSC) Part 6: Determination of oxidation induction time (isothermal OIT) and oxidation induction temperature (dynamic OIT)
    ISO 306:2013 Plastics Thermoplastic materials Determination of Vicat softening temperature (VST)
    ISO 4435:2003 Plastics piping systems for non-pressure underground drainage and sewerage Unplasticized poly(vinyl chloride) (PVC-U)
    EN 15344 : 2007 PLASTICS - RECYCLED PLASTICS - CHARACTERISATION OF POLYETHYLENE (PE) RECYCLATES
    ISO 9967:2016 Thermoplastics pipes Determination of creep ratio
    ISO 13254:2010 Thermoplastics piping systems for non-pressure applications Test method for watertightness
    ISO 178:2010 Plastics Determination of flexural properties
    ISO 9969:2016 Thermoplastics pipes Determination of ring stiffness
    EN 12099:1997 Plastics piping systems - Polyethylene piping materials and components - Determination of volatile content
    ISO 9852:2007 Unplasticized poly(vinyl chloride) (PVC-U) pipes Dichloromethane resistance at specified temperature (DCMT) Test method
    ISO 1167-1:2006 Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 1: General method
    ISO 2505:2005 Thermoplastics pipes Longitudinal reversion Test method and parameters
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective