API 613:2003
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
SPECIAL PURPOSE GEAR UNITS FOR PETROLEUM, CHEMICAL AND GAS INDUSTRY SERVICES
Hardcopy , PDF
02-22-2021
English
01-01-2010
1 GENERAL
2 BASIC DESIGN
3 ACCESSORIES
4 INSPECTION, TESTING, AND PREPARATION
FOR SHIPMENT
5 VENDOR'S DATA
APPENDIX A - SPECIAL PURPOSE GEAR UNITS
DATA SHEETS
APPENDIX B - REFERENCES
APPENDIX C - COUPLINGS FOR HIGH SPEED
GEAR UNITS
APPENDIX D - RATED LOAD CURVES FOR THRUST
BEARINGS WITH STANDARD
6 X 6 SHOES
APPENDIX E - MATERIAL SPECIFICATIONS FOR
SPECIAL PURPOSE GEAR UNITS
PAGE
APPENDIX F - VENDOR DRAWING AND DATA
REQUIREMENTS
APPENDIX G - RESIDUAL UNBALANCE WORK SHEETS
APPENDIX H - GEAR INSPECTION (INFORMATIVE)
APPENDIX I - INSPECTOR'S CHECKLIST
APPENDIX J - RATING COMPARISON API 613 VS.
AGMA 2
APPENDIX K - SHAFT END SIZING METHOD
APPENDIX L - TYPICAL MOUNTING PLATES
Describes the minimum requirements for special-purpose, enclosed, precision single- and double-helical one- and two-stage speed increasers and reducers of parallel-shaft design for petroleum, chemical and gas industry services.
DocumentType |
Standard
|
Pages |
104
|
ProductNote |
Reconfirmed 2003
|
PublisherName |
American Petroleum Institute
|
Status |
Superseded
|
ASME PV CODE 8 DIV 2 : 2017 | BOILER AND PRESSURE VESSEL CODE - RULES FOR CONSTRUCTION OF PRESSURE VESSELS DIVISION 2- ALTERNATIVE RULES |
AGMA 6011 : I | SPECIFICATION FOR HIGH SPEED HELICAL GEAR UNITS |
ISO 7005-2:1988 | Metallic flanges — Part 2: Cast iron flanges |
ISO 965-5:1998 | ISO general purpose metric screw threads — Tolerances — Part 5: Limits of sizes for internal screw threads to mate with hot-dip galvanized external screw threads with maximum size of tolerance position h before galvanizing |
SAE J 518 : 2013 | HYDRAULIC FLANGED TUBE, PIPE, AND HOSE CONNECTIONS, FOUR-BOLT SPLIT FLANGE TYPE |
ASME PV CODE 9 : 2017 | BOILER AND PRESSURE VESSEL CODE - WELDING, BRAZING, AND FUSING QUALIFICATIONS - QUALIFICATION STANDARD FOR WELDING, BRAZING, AND FUSING PROCEDURES; WELDERS; BRAZERS; AND WELDING, BRAZING, AND FUSING OPERATORS |
AGMA 6025 : D | SOUND FOR ENCLOSED HELICAL, HERRINGBONE AND SPIRAL BEVEL GEAR DRIVES |
NEMA SM 23-1991 (R1997, R2002) | STEAM TURBINES FOR MECHANICAL DRIVE SERVICE |
AGMA 2101 : D | FUNDAMENTAL RATING FACTORS AND CALCULATION METHODS FOR INVOLUTE SPUR AND HELICAL GEAR TEETH (METRIC EDITION) |
ASME PV CODE 8 DIV 1 : 2017 | BOILER AND PRESSURE VESSEL CODE - RULES FOR CONSTRUCTION OF PRESSURE VESSELS DIVISION 1 |
AGMA ISO 1328 1 : B2014 | CYLINDRICAL GEARS - ISO SYSTEM OF FLANK TOLERANCE CLASSIFICATION - PART 1: DEFINITIONS AND ALLOWABLE VALUES OF DEVIATIONS RELEVANT TO FLANKS OF GEAR TEETH |
ISO 724:1993 | ISO general-purpose metric screw threads — Basic dimensions |
API 614 : 2008 | LUBRICATION, SHAFT-SEALING AND OIL-CONTROL SYSTEMS AND AUXILIARIES |
ASME B16.11 : 2016 | FORGED FITTINGS, SOCKET-WELDING AND THREADED |
AGMA 6010 : F | STANDARD FOR SPUR, HELICAL, HERRINGBONE AND BEVEL ENCLOSED DRIVES |
NEMA 250 : 2014 | ENCLOSURES FOR ELECTRICAL EQUIPMENT (1000 VOLTS MAXIMUM) |
ASME B16.42 : 2016 | DUCTILE IRON PIPE FLANGES AND FLANGED FITTINGS - CLASSES 150 AND 300 |
ISO 965-2:1998 | ISO general purpose metric screw threads — Tolerances — Part 2: Limits of sizes for general purpose external and internal screw threads — Medium quality |
ASME PV CODE 8 DIV 3 : 2017 | BPVC Section VIII-BOILER AND PRESSURE VESSEL CODE - RULES FOR CONSTRUCTION OF PRESSURE VESSELS - ALTERNATIVE RULES FOR CONSTRUCTION OF HIGH PRESSURE VESSELS |
AGMA 6001 : D | DESIGN AND SELECTION OF COMPONENTS FOR ENCLOSED GEAR DRIVES |
ISO 6708:1995 | Pipework components Definition and selection of DN (nominal size) |
ISO 6336-5:2016 | Calculation of load capacity of spur and helical gears Part 5: Strength and quality of materials |
ISO 262:1998 | ISO general purpose metric screw threads — Selected sizes for screws, bolts and nuts |
ASME B16.1 : 2015 | Gray Iron Pipe Flanges and Flanged Fittings: Classes 25, 125, and 250 |
ASME B1.20.1 : 2013(R2018) | PIPE THREADS, GENERAL PURPOSE (INCH) |
ASME B17.1 : 1967 | KEYS AND KEYSEATS |
API 670 : 2014 | MACHINERY PROTECTION SYSTEMS |
AGMA 925 : A | EFFECT OF LUBRICATION ON GEAR SURFACE DISTRESS |
ISO 7-1:1994 | Pipe threads where pressure-tight joints are made on the threads Part 1: Dimensions, tolerances and designation |
ISO 965-4:1998 | ISO general purpose metric screw threads Tolerances Part 4: Limits of sizes for hot-dip galvanized external screw threads to mate with internal screw threads tapped with tolerance position H or G after galvanizing |
API 617 : 2014 | AXIAL AND CENTRIFUGAL COMPRESSORS AND EXPANDER-COMPRESSORS |
AGMA 908 : B | GEOMETRY FACTORS FOR DETERMINING THE PITTING RESISTANCE AND BENDING STRENGTH OF SPUR, HELICAL AND HERRINGBONE GEAR TEETH |
NFPA 70 : 2017 | NATIONAL ELECTRICAL CODE |
ISO 15071:2011 | Hexagon bolts with flange Small series Product grade A |
IEC 60079-0:2011 | Explosive atmospheres - Part 0: Equipment - General requirements |
EN 1563:2011 | Founding - Spheroidal graphite cast irons |
ASTM E 125 : 1963 : R2003 | Standard Reference Photographs for Magnetic Particle Indications on Ferrous Castings |
ASME B16.5 : 2017 | PIPE FLANGES AND FLANGED FITTINGS: NPS 1/2 THROUGH NPS 24 METRIC/INCH STANDARD |
EN 10083-1:2006 | Steels for quenching and tempering - Part 1: General technical delivery conditions |
API 672 : 2004 | PACKAGED, INTEGRALLY GEARED CENTRIFUGAL AIR COMPRESSORS FOR PETROLEUM, CHEMICAL, AND GAS INDUSTRY SERVICES |
ASME PV CODE 5 : 2017 | BOILER AND PRESSURE VESSEL CODE - NONDESTRUCTIVE EXAMINATION |
EN 10083-2:2006 | Steels for quenching and tempering - Part 2: Technical delivery conditions for non alloy steels |
ISO 261:1998 | ISO general purpose metric screw threads General plan |
API 686 : 2009 | RECOMMENDED PRACTICE FOR MACHINERY INSTALLATION AND INSTALLATION DESIGN |
ISO 965-1:2013 | ISO general purpose metric screw threads — Tolerances — Part 1: Principles and basic data |
EN 10084:2008 | Case hardening steels - Technical delivery conditions |
ISO 7005-1:2011 | Pipe flanges — Part 1: Steel flanges for industrial and general service piping systems |
ASTM E 709 : 2015 : REDLINE | Standard Guide for Magnetic Particle Testing |
ASTM A 515/A515M : 2017 : REDLINE | Standard Specification for Pressure Vessel Plates, Carbon Steel, for Intermediate- and Higher-Temperature Service |
ISO 965-3:1998 | ISO general purpose metric screw threads Tolerances Part 3: Deviations for constructional screw threads |
ISO 3448:1992 | Industrial liquid lubricants — ISO viscosity classification |
EN 10083-3:2006/AC:2008 | STEELS FOR QUENCHING AND TEMPERING - PART 3: TECHNICAL DELIVERY CONDITIONS FOR ALLOY STEELS |
ISO/TR 10064-1:2017 | Code of inspection practice Part 1: Measurement of cylindrical gear tooth flanks |
EN 1561:2011 | Founding - Grey cast irons |
AGMA 2001 : D | FUNDAMENTAL RATING FACTORS AND CALCULATION METHODS FOR INVOLUTE SPUR AND HELICAL GEAR TEETH |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.