IEC TS 60034-17 : 4.0

Superseded View Superseded By

Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

ROTATING ELECTRICAL MACHINES - PART 17: CAGE INDUCTION MOTORS WHEN FED FROM CONVERTERS - APPLICATION GUIDE

Publisher: International Electrotechnical Committee

Published: 05-09-2006

Available Formats: PDF - English - French, Hardcopy - English - French
More Info on product formats

Table of Contents - (Show below) - (Hide below)

INTRODUCTION
1 Scope
2 Normative references
3 Characteristics of the motor
4 Frequency spectrum of voltage and/or currents
5 Losses caused by harmonics
6 Torque derating during converter operation
7 Oscillating torques
8 Magnetically excited noise
9 Service life of the insulation system
10 Bearing currents
11 Installation (cabling, grounding, bonding)
12 Maximum safe operating speed
13 Power factor correction
Figures

Abstract - (Show below) - (Hide below)

Describes the steady-state operation of cage induction motors within the scope of IEC 60034-12, when fed from converters. It covers the operation over the whole speed setting range.

General Product Information - (Show below) - (Hide below)

Published
Document Type	Standard
Status	Superseded
Publisher	International Electrotechnical Committee
Pages
ISBN
Committee	TC 2
Supersedes	95/214653 DC : NOV 95
Superseded By	IEC TS 60034-25 : 3.0

International Equivalents – Equivalent Standard(s) & Relationship - (Show below) - (Hide below)

Equivalent Standard(s)	Relationship
DD IEC TS 60034-17 : 2006	Identical
SANS 60034-17 : 4ED 2006(R2011)	Identical
AS 60034.17-2009	Identical
VDE 0530-17 : 2007	Identical
GOST R IEC/TS 60034-17 : 2009	Identical
DIN VDE 0530-17 : 2007	Corresponds
NEN NPR IEC/TS 60034-17 : 2002 C2 2003	Identical
GOST R IEC/TS 60034-17 : 2009	Identical
NEN NPR IEC CLC/TS 60034-17 : 2004	Identical
DD IEC TS 60034-17 : 2006	Identical
DIN VDE 0530-17 : 2007	Corresponds
VDE 0530-17 : 2007	Identical
SANS 60034-17 : 4ED 2006(R2011)	Identical
CLC/TS 60034-17 : 2004	Identical
DIN IEC TS 60034-17 : 2004	Identical
AS 60034.17-2009	Identical

Standards Referenced By This Book - (Show below) - (Hide below)

08/30183108 DC : DRAFT MAY 2008	BS IEC/TS 60034-31 - ROTATING ELECTRICAL MACHINES - PART 31: GUIDE FOR THE SELECTION AND APPLICATION OF ENERGY-EFFICIENT MOTORS INCLUDING VARIABLE-SPEED APPLICATIONS
VDI 3839-5 : 2001	INSTRUCTIONS ON MEASURING AND INTERPRETING THE VIBRATION OF MACHINES - TYPICAL VIBRATION PATTERNS WITH ELECTRICAL MACHINES
BS EN 60079-7 : 2015	EXPLOSIVE ATMOSPHERES - PART 7: EQUIPMENT PROTECTION BY INCREASED SAFETY 'E' (IEC 60079-7:2015)
UNE EN 50533 : 2012	RAILWAY APPLICATIONS - THREE-PHASE TRAIN LINE VOLTAGE CHARACTERISTICS
BS EN 60034-30 : 2009	ROTATING ELECTRICAL MACHINES - PART 30: EFFICIENCY CLASSES OF SINGLE-SPEED, THREE-PHASE, CAGE-INDUCTION MOTORS (IE-CODE)
ISO 18652 : 2005(R2010)	BUILDING CONSTRUCTION MACHINERY AND EQUIPMENT - EXTERNAL VIBRATORS FOR CONCRETE
CEI 301-3 : 2005	GUIDE FOR THE CHARACTERISATION AND IDENTIFICATION OF VARIABLE SPEED ELECTRICAL DRIVES BY MEANS OF A PLATE
UNE-EN 60079-15:2013	EXPLOSIVE ATMOSPHERES - PART 15: EQUIPMENT PROTECTION BY TYPE OF PROTECTION 'N'
CEI EN 60027-4 : 2008	LETTER SYMBOLS TO BE USED IN ELECTRICAL TECHNOLOGY - PART 4: ROTATING ELECTRICAL MACHINES
07/30168628 DC : 0	BS EN 60079-15 - EXPLOSIVE ATMOSPHERES - PART 15: EQUIPMENT PROTECTION BY TYPE OF PROTECTION "N"
CEI CLC/TS 50534 : 2011	RAILWAY APPLICATIONS - GENERIC SYSTEM ARCHITECTURES FOR ONBOARD ELECTRIC AUXILIARY POWER SYSTEMS
09/30182105 DC : 0	BS EN 60349-2 - ELECTRICAL TRACTION - ROTATING ELECTRICAL MACHINES FOR RAIL AND ROAD VEHICLES - PART 2: ELECTRONIC CONVERTER-FED ALTERNATING CURRENT MOTORS
BS EN 60349-2 : 2010	ELECTRIC TRACTION - ROTATING ELECTRICAL MACHINES FOR RAIL AND ROAD VEHICLES - PART 2: ELECTRONIC CONVERTER-FED ALTERNATING CURRENT MOTORS
DD CLC/TS 50534 : 2010	RAILWAY APPLICATIONS - GENERIC SYSTEM ARCHITECTURES FOR ONBOARD ELECTRIC AUXILIARY POWER SYSTEMS
NF EN 50533 : 2012 AMD 1 2018	RAILWAY APPLICATIONS - THREE-PHASE TRAIN LINE VOLTAGE CHARACTERISTICS
BS EN 60349-4 : 2013	ELECTRIC TRACTION - ROTATING ELECTRICAL MACHINES FOR RAIL AND ROAD VEHICLES - PART 4: PERMANENT MAGNET SYNCHRONOUS ELECTRICAL MACHINES CONNECTED TO AN ELECTRONIC CONVERTER
09/30209334 DC : 0	BS EN 60034-2-3 - ROTATING ELECTRICAL MACHINES - PART 2-3: SPECIFIC TEST METHODS FOR DETERMINING LOSSES AND EFFICIENCY OF CONVERTER-FED AC MOTORS
SR CLC/TS 60034-25:2008	ROTATING ELECTRICAL MACHINES - PART 25: GUIDANCE FOR THE DESIGN AND PERFORMANCE OF A.C. MOTORS SPECIFICALLY DESIGNED FOR CONVERTER SUPPLY
13/30287323 DC : 0	BS EN 60034-1 ED 13.0 - ROTATING ELECTRICAL MACHINES - PART 1: RATING AND PERFORMANCE
09/30214359 DC : 0	BS EN 50533 - RAILWAY APPLICATIONS - THREE-PHASE TRAIN LINE VOLTAGE CHARACTERISTICS
DD CLC/TS 60034-31 : 2011	ROTATING ELECTRICAL MACHINES - PART 31: SELECTION OF ENERGY-EFFICIENT MOTORS INCLUDING VARIABLE SPEED APPLICATIONS - APPLICATION GUIDE
14/30278882 DC : 0	BS EN 60079-7 IEC 60079-7 ED. 5.0 - EXPLOSIVE ATMOSPHERES - PART 7: EQUIPMENT PROTECTION BY INCREASED SAFETY 'E'
07/30161347 DC : 0	BS EN 60034-30 - ROTATING ELECTRICAL MACHINES - PART 30: EFFICIENCY CLASSES OF SINGLE-SPEED THREE-PHASE CAGE INDUCTION MOTORS
BS EN 61800-4 : 2003	ADJUSTABLE SPEED ELECTRICAL POWER DRIVE SYSTEMS - PART 4: GENERAL REQUIREMENTS - RATING SPECIFICATIONS FOR A.C. POWER DRIVE SYSTEMS ABOVE 1000 V A.C. AND NOT EXCEEDING 35 KV
PREN 50533 : DRAFT 2009	RAILWAY APPLICATIONS - THREE-PHASE TRAIN LINE VOLTAGE CHARACTERISTICS
BS EN 45510-2-5 : 2002	GUIDE FOR PROCUREMENT OF POWER STATION EQUIPMENT - PART 2-5: ELECTRICAL EQUIPMENT - MOTORS
11/30206274 DC : 0	BS EN 60349-4 - ELECTRIC TRACTION ROTATING ELECTRICAL MACHINES FOR RAIL AND ROAD VEHICLES - PART 4: PERMANENT MAGNET SYNCHRONOUS ELECTRICAL MACHINES CONNECTED TO AN ELECTRONIC CONVERTER
BS EN 60079-0 : 2012	EXPLOSIVE ATMOSPHERES - PART 0: EQUIPMENT - GENERAL REQUIREMENTS
DIN EN 15268 E : 2008	PETROL FILLING STATIONS - SAFETY REQUIREMENTS FOR THE CONSTRUCTION OF SUBMERSIBLE PUMP ASSEMBLIES
DD IEC TS 60034-31 : DRAFT JULY 2010	ROTATING ELECTRICAL MACHINES - PART 31: SELECTION OF ENERGY-EFFICIENT MOTORS INCLUDING VARIABLE SPEED APPLICATIONS - APPLICATION GUIDE
BS EN 50533 : 2011	RAILWAY APPLICATIONS - THREE-PHASE TRAIN LINE VOLTAGE CHARACTERISTICS
BS EN 60034-1 : 2010	ROTATING ELECTRICAL MACHINES - PART 1: RATING AND PERFORMANCE
CEI UNI EN 45510-2-5 : 2006	GUIDE FOR PROCUREMENT OF POWER STATION EQUIPMENT - PART 2-5: ELECTRICAL EQUIPMENT - MOTORS
DIN EN 15268 : 2008	PETROL FILLING STATIONS - SAFETY REQUIREMENTS FOR THE CONSTRUCTION OF SUBMERSIBLE PUMP
04/30113660 DC : DRAFT MAY 2004	IEC 60079-7 - ELECTRICAL APPARATUS FOR EXPLOSIVE GAS ATMOSPHERES - PART 7: INCREASED SAFETY 'E'
BS EN 15268 : 2008	PETROL FILLING STATIONS - SAFETY REQUIREMENTS FOR THE CONSTRUCTION OF SUBMERSIBLE PUMP ASSEMBLIES
DD CLC/TS 60034-25 : 2008	ROTATING ELECTRICAL MACHINES - PART 25: GUIDANCE FOR THE DESIGN AND PERFORMANCE OF A.C. MOTORS SPECIFICALLY DESIGNED FOR CONVERTER SUPPLY
NBR IEC 60034-9 : 2011	ROTATING ELECTRICAL MACHINES - PART 9: NOISE LIMITS
BS IEC 61892-3 : 2012	MOBILE AND FIXED OFFSHORE UNITS - ELECTRICAL INSTALLATIONS - PART 3: EQUIPMENT
UNE EN 60027-4 : 2011	LETTER SYMBOLS TO BE USED IN ELECTRICAL TECHNOLOGY - PART 4: ROTATING ELECTRIC MACHINES
08/30182672 DC : DRAFT MAY 2008	BS EN 60034-1 - ROTATING ELECTRICAL MACHINES - PART 1: RATING AND PERFORMANCE
03/113813 DC : 0	IEC 60034-2. ED.4 - ROTATING ELECTRICAL MACHINES - PART 2: METHODS FOR DETERMINING LOSSES AND EFFICIENCY FROM TESTS (EXCLUDING MACHINES FOR TRACTION VEHICLES)
BS EN 60027-4 : 2007	LETTER SYMBOLS TO BE USED IN ELECTRIC TECHNOLOGY - PART 4: ROTATING ELECTRIC MACHINES
02/107764 DC : DRAFT DEC 2002	ISO 18652 - BUILDING CONSTRUCTION MACHINERY AND EQUIPMENT - EXTERNAL VIBRATORS FOR CONCRETE
UNE-EN 60034-1:2011	ROTATING ELECTRICAL MACHINES - PART 1: RATING AND PERFORMANCE
07/30065083 DC : DRAFT JUNE 2007	BS EN 60027-4 - LETTER SYMBOLS TO BE USED IN ELECTRICAL TECHNOLOGY - PART 4: ROTATING ELECTRIC MACHINES
CEI EN 60034-1 : 2015	ROTATING ELECTRICAL MACHINES - PART 1: RATING AND PERFORMANCE
CSA C22.2 No. 60079.0 : 2015	EXPLOSIVE ATMOSPHERES - PART 0: EQUIPMENT - GENERAL REQUIREMENTS
I.S. EN 60079-14:2014	EXPLOSIVE ATMOSPHERES - PART 14: ELECTRICAL INSTALLATIONS DESIGN, SELECTION AND ERECTION
08/30180328 DC : DRAFT MAR 2008	BS EN 61800-8 - ADJUSTABLE SPEED ELECTRICAL POWER DRIVE SYSTEMS - PART 8: SPECIFICATION OF VOLTAGE ON THE POWER INTERFACE
I.S. EN 60349-2:2010	ELECTRIC TRACTION - ROTATING ELECTRICAL MACHINES FOR RAIL AND ROAD VEHICLES - PART 2: ELECTRONIC CONVERTER-FED ALTERNATING CURRENT MOTORS
BS EN 60034-9 : 2005	ROTATING ELECTRICAL MACHINES - PART 9: NOISE LIMITS
I.S. EN 60349-4:2013	ELECTRIC TRACTION - ROTATING ELECTRICAL MACHINES FOR RAIL AND ROAD VEHICLES - PART 4: PERMANENT MAGNET SYNCHRONOUS ELECTRICAL MACHINES CONNECTED TO AN ELECTRONIC CONVERTER (IEC 60349-4:2012 (EQV))
CLC/TS 50534 : 2010	RAILWAY APPLICATIONS - GENERIC SYSTEM ARCHITECTURES FOR ONBOARD ELECTRIC AUXILIARY POWER SYSTEMS
I.S. EN 50533:2011	RAILWAY APPLICATIONS - THREE-PHASE TRAIN LINE VOLTAGE CHARACTERISTICS
I.S. EN 60079-7:2015	EXPLOSIVE ATMOSPHERES - PART 7: EQUIPMENT PROTECTION BY INCREASED SAFETY 'E'
I.S. EN 60034-30:2009	ROTATING ELECTRICAL MACHINES - PART 30: EFFICIENCY CLASSES OF SINGLE-SPEED, THREE-PHASE, CAGE-INDUCTION MOTORS
I.S. CLC TS 60034-25:2005	ROTATING ELECTRICAL MACHINES - PART 25: GUIDE FOR THE DESIGN AND PERFORMANCE OF CAGE INDUCTION MOTORS SPECIFICALLY DESIGNED FOR CONVERTER SUPPLY
UNI EN 15268 : 2009	PETROL FILLING STATIONS - SAFETY REQUIREMENTS FOR THE CONSTRUCTION OF SUBMERSIBLE PUMP ASSEMBLIES
I.S. EN 60079-15:2010	EXPLOSIVE ATMOSPHERES - PART 15: EQUIPMENT PROTECTION BY TYPE OF PROTECTION 'N'
I.S. EN 60034-9:2005	ROTATING ELECTRICAL MACHINES - PART 9: NOISE LIMITS
CSA C22.2 No. 60079-7 : 2016	EXPLOSIVE ATMOSPHERES - PART 7: EQUIPMENT PROTECTION BY INCREASED SAFETY 'E'
UNE-EN 60079-7:2016	EXPLOSIVE ATMOSPHERES - PART 7: EQUIPMENT PROTECTION BY INCREASED SAFETY 'E'
SR CLC/TS 60034-31:2011	ROTATING ELECTRICAL MACHINES - PART 31: SELECTION OF ENERGY-EFFICIENT MOTORS INCLUDING VARIABLE SPEED APPLICATIONS - APPLICATION GUIDE
BS EN 60079-15 : 2010	EXPLOSIVE ATMOSPHERES - PART 15: EQUIPMENT PROTECTION BY TYPE OF PROTECTION 'N'
CSA C22.2 No. 60079-15 : 2016	EXPLOSIVE ATMOSPHERES - PART 15: EQUIPMENT PROTECTION BY TYPE OF PROTECTION 'N'
CEI EN 60079-15 : 2012	EXPLOSIVE ATMOSPHERES - PART 15: EQUIPMENT PROTECTION BY TYPE OF PROTECTION 'N'
NF EN 60034-1 : 2011	ROTATING ELECTRICAL MACHINES - PART 1: RATING AND PERFORMANCE
CEI EN 50533 : 2012	RAILWAY APPLICATIONS - THREE-PHASE TRAIN LINE VOLTAGE CHARACTERISTICS
I.S. EN 60027-4:2007	LETTER SYMBOLS TO BE USED IN ELECTRIC TECHNOLOGY - PART 4: ROTATING ELECTRIC MACHINES
01/202453 DC : DRAFT APRIL 2001	IEC 60034-9 ED.4 - ROTATING ELECTRICAL MACHINERY - PART 9: NOISE LIMITS
CLC/TS 60034-31 : 2011	ROTATING ELECTRICAL MACHINES - PART 31: SELECTION OF ENERGY-EFFICIENT MOTORS INCLUDING VARIABLE SPEED APPLICATIONS - APPLICATION GUIDE
BIS IS/IEC 60034-1 : 2004 AMD 1 2015	ROTATING ELECTRICAL MACHINES - PART 1: RATING AND PERFORMANCE
UNE EN 60349-4 : 2013	ELECTRIC TRACTION - ROTATING ELECTRICAL MACHINES FOR RAIL AND ROAD VEHICLES - PART 4: PERMANENT MAGNET SYNCHRONOUS ELECTRICAL MACHINES CONNECTED TO AN ELECTRONIC CONVERTER
SR CLC/TS 50534:2010	RAILWAY APPLICATIONS - GENERIC SYSTEM ARCHITECTURES FOR ONBOARD ELECTRIC AUXILIARY POWER SYSTEMS
I.S. EN 60079-0:2012	EXPLOSIVE ATMOSPHERES - PART 0: EQUIPMENT - GENERAL REQUIREMENTS (IEC 60079-0:2011 (MOD))
IEC TS 61800-8 : 1.0	ADJUSTABLE SPEED ELECTRICAL POWER DRIVE SYSTEMS - PART 8: SPECIFICATION OF VOLTAGE ON THE POWER INTERFACE
IEC TS 60034-31 : 1.0	ROTATING ELECTRICAL MACHINES - PART 31: SELECTION OF ENERGY-EFFICIENT MOTORS INCLUDING VARIABLE SPEED APPLICATIONS - APPLICATION GUIDE
IEC 61892-3 : 3.0	MOBILE AND FIXED OFFSHORE UNITS - ELECTRICAL INSTALLATIONS - PART 3: EQUIPMENT
I.S. EN 15268:2008	PETROL FILLING STATIONS - SAFETY REQUIREMENTS FOR THE CONSTRUCTION OF SUBMERSIBLE PUMP ASSEMBLIES
IEC 60079-7:2015-06+AMD1:2017-08 CSV	EXPLOSIVE ATMOSPHERES - PART 7: EQUIPMENT PROTECTION BY INCREASED SAFETY 'E'
IEC 60079-7:2015+AMD1:2017 CSV	EXPLOSIVE ATMOSPHERES - PART 7: EQUIPMENT PROTECTION BY INCREASED SAFETY 'E'
EN 60079-7 : 2015 AMD 1 2018	EXPLOSIVE ATMOSPHERES - PART 7: EQUIPMENT PROTECTION BY INCREASED SAFETY 'E' (IEC 60079-7:2015/A1:2017)
DIN EN 12101-3 : 2015	SMOKE AND HEAT CONTROL SYSTEMS - PART 3: SPECIFICATION FOR POWERED SMOKE AND HEAT CONTROL VENTILATORS (FANS)
DIN EN 12101-3 E : 2015	SMOKE AND HEAT CONTROL SYSTEMS - PART 3: SPECIFICATION FOR POWERED SMOKE AND HEAT CONTROL VENTILATORS (FANS)
BS EN 12101-3 : 2015	SMOKE AND HEAT CONTROL SYSTEMS - SPECIFICATION FOR POWERED SMOKE AND HEAT EXHAUST VENTILATORS (FANS)
12/30269297 DC : 0	BS EN 60079-14/ED 5 - EXPLOSIVE ATMOSPHERES - PART 14: ELECTRICAL INSTALLATIONS DESIGN, SELECTION AND ERECTION
IEC 60034-30 : 1.0	ROTATING ELECTRICAL MACHINES - PART 30: EFFICIENCY CLASSES OF SINGLE-SPEED, THREE-PHASE, CAGE-INDUCTION MOTORS (IE-CODE)
UNE-EN 60349-2:2011	ELECTRIC TRACTION - ROTATING ELECTRICAL MACHINES FOR RAIL AND ROAD VEHICLES - PART 2: ELECTRONIC CONVERTER-FED ALTERNATING CURRENT MOTORS
UNE-EN 60079-14:2016	EXPLOSIVE ATMOSPHERES - PART 14: ELECTRICAL INSTALLATIONS DESIGN, SELECTION AND ERECTION
IEC 60349-2 : 3.0	ELECTRIC TRACTION - ROTATING ELECTRICAL MACHINES FOR RAIL AND ROAD VEHICLES - PART 2: ELECTRONIC CONVERTER-FED ALTERNATING CURRENT MOTORS
UNE EN 12101-3 : 2016	SMOKE AND HEAT CONTROL SYSTEMS - PART 3: SPECIFICATION FOR POWERED SMOKE AND HEAT CONTROL VENTILATORS (FANS)
09/30206527 DC : 0	BS EN 60079-0 ED 6.0 - EXPLOSIVE ATMOSPHERES - PART 0: EQUIPMENT - GENERAL REQUIREMENTS
05/30138005 DC : DRAFT AUG 2005	IEC 60079-14 ED 4 - ELECTRICAL APPARATUS FOR EXPLOSIVE GAS ATMOSPHERES - PART 14: ELECTRICAL INSTALLATIONS IN HAZARDOUS AREAS (OTHER THAN MINES)
DD IEC TS 61800-8 : 2010	ADJUSTABLE SPEED ELECTRICAL POWER DRIVE SYSTEMS - PART 8: SPECIFICATION OF VOLTAGE ON THE POWER INTERFACE
UNE-EN 60079-0:2013	EXPLOSIVE ATMOSPHERES - PART 0: EQUIPMENT - GENERAL REQUIREMENTS
IEC 60034-9 : 4.1	ROTATING ELECTRICAL MACHINES - PART 9: NOISE LIMITS
IEC 60349-4 : 1ED 2012	ELECTRIC TRACTION - ROTATING ELECTRICAL MACHINES FOR RAIL AND ROAD VEHICLES - PART 4: PERMANENT MAGNET SYNCHRONOUS ELECTRICAL MACHINES CONNECTED TO AN ELECTRONIC CONVERTER
BS EN 60079-14 : 2014	EXPLOSIVE ATMOSPHERES - PART 14: ELECTRICAL INSTALLATIONS DESIGN, SELECTION AND ERECTION
BIS IS/IEC 60079-0 : 2011	EXPLOSIVE ATMOSPHERES - PART 0: GENERAL REQUIREMENTS

Standards Referencing This Book - (Show below) - (Hide below)

IEC TS 60034-25 : 3.0	ROTATING ELECTRICAL MACHINES - PART 25: AC ELECTRICAL MACHINES USED IN POWER DRIVE SYSTEMS - APPLICATION GUIDE
IEC 60034-1 : 13.0	ROTATING ELECTRICAL MACHINES - PART 1: RATING AND PERFORMANCE
IEC 60034-12 : 3.0	ROTATING ELECTRICAL MACHINES - PART 12: STARTING PERFORMANCE OF SINGLE-SPEED THREE-PHASE CAGE INDUCTION MOTORS

Add To Cart

Product Format

Quantity

add to cart

IEC TS 60034-17 : 4.0

Table of Contents - (Show below) - (Hide below)

Abstract - (Show below) - (Hide below)

General Product Information - (Show below) - (Hide below)

International Equivalents – Equivalent Standard(s) & Relationship - (Show below) - (Hide below)

Standards Referenced By This Book - (Show below) - (Hide below)

Standards Referencing This Book - (Show below) - (Hide below)

Add To Cart

Publisher

Category

Sub Category

Access your standards online with a subscription?