Standard Specification for Brass Plate, Sheet, Strip, And Rolled Bar

Available format(s)

Hardcopy , PDF

Language(s)

English

Published date

10-11-2023

Publisher

American Society for Testing and Materials

1.1This specification establishes the requirements for brass (copper-zinc alloy) plate, sheet, strip, and rolled bar of the following alloys:

Copper Alloy UNS No.	Type of Metal

C21000	Gilding
C22000	Commerical Bronze
C22600	Jewerly Bronze
C23000	Red Brass
C24000	Low Brass
C26000	Cartridge Brass
C26800	Yellow Brass
C27200	…
C28000	Muntz Metal

1.2Units—The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

1.3The following safety hazard caveat pertains only to the test method(s) described in this specification.

1.3.1This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Committee	B 05
DocumentType	Standard
Pages	9
PublisherName	American Society for Testing and Materials
Status	Current
Supersedes	ASTM B 36/B36M : 2018

ASTM B 315 : 2019	Standard Specification for Seamless Copper Alloy Pipe and Tube
ASTM E 18 : 2022	Standard Test Methods for Rockwell Hardness of Metallic Materials
ASTM D 3433 : 1999 : R2020	Standard Test Method for Fracture Strength in Cleavage of Adhesives in Bonded Metal Joints
ASTM F 1387 : 2023	Standard Specification for Performance of Piping and Tubing Mechanically Attached Fittings
ASTM F 1144 : 2019	Standard Specification for Manhole Cover Assembly, Bolted, Semi-Flush, Oiltight and Watertight, Hinged
ASTM D 3528 : 1996 : R2016	Standard Test Method for Strength Properties of Double Lap Shear Adhesive Joints by Tension Loading
ASTM D 4054 : 2023	Standard Practice for Evaluation of New Aviation Turbine Fuels and Fuel Additives
ASTM F 1018 : 2022	Standard Specification for Steel Emergency Gear Stowage Locker
ASTM D 5363 : 2016	Standard Specification for Anaerobic Single-Component Adhesives (AN)
ASTM F 1142 : 2019	Standard Specification for Manhole Cover Assembly, Bolted, Semi-Flush, Oiltight and Watertight
ASTM D 1002 : 2010 : R2019	Standard Test Method for Apparent Shear Strength of Single-Lap-Joint Adhesively Bonded Metal Specimens by Tension Loading (Metal-to-Metal)
ASTM B 248M : 2022	Standard Specification for General Requirements for Wrought Copper and Copper-Alloy Plate, Sheet, Strip, and Rolled Bar (Metric)
ASTM D 8040 : 2018 : R2023	Standard Test Method for Corrosion Test for Heat Transfer Fluids in Glassware
ASTM B 248 : 2022	Standard Specification for General Requirements for Wrought Copper and Copper-Alloy Plate, Sheet, Strip, and Rolled Bar
ASTM D 1384 : 2005 : R2019	Standard Test Method for Corrosion Test for Engine Coolants in Glassware
ASTM D 3658 : 2001 : R2016	Standard Test Method for Determining the Torque Strength of Ultraviolet (UV) Light-Cured Glass/Metal Adhesive Joints
ASTM B 927/B927M : 2017	Standard Specification for Brass Rod, Bar, and Shapes
ASTM F 992 : 2017 : R2022	Standard Specification for Valve Label Plates
ASTM D 3165 : 2007 : R2023	Standard Test Method for Strength Properties of Adhesives in Shear by Tension Loading of Single-Lap-Joint Laminated Assemblies
ASTM F 1974 : 2023	Standard Specification for Metal Insert Fittings for Polyethylene/Aluminum/Polyethylene and Crosslinked Polyethylene/Aluminum/Crosslinked Polyethylene Composite Pressure Pipe
ASTM F 1143 : 2019	Standard Specification for Manhole Cover Assembly, Bolted, Raised, Oiltight and Watertight

ASTM E 8/E8M : 2024	Standard Test Methods for Tension Testing of Metallic Materials
ASTM E 8/E8M : 2022	Standard Test Methods for Tension Testing of Metallic Materials