ASTM F 1041 : 2002 : R2016
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Standard Guide for Squeeze-Off of Polyolefin Gas Pressure Pipe and Tubing
Hardcopy , PDF
09-03-2020
English
05-01-2016
CONTAINED IN VOL. 08.04, 2017 Specifies general procedures for squeeze-off of polyolefin gas pressure pipe and tubing.
1.1This guide describes general procedures for squeeze-off of polyolefin gas pressure pipe and tubing. Pipe and squeeze tool manufacturers shall be requested to supply recommendations for squeeze-off with materials or products.
1.2Governing codes and project specifications should be consulted. Nothing in this document should be construed as recommending practices or systems at variance with governing codes and project specifications.
1.3This guide covers squeeze-off of polyolefin pipe and tubing in accordance with Specification D2513.
1.4Where applicable in this guide, “pipe” shall mean “pipe and tubing.”
1.5Units–The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are mathematical conversions to SI units, which are provided for information only and are not considered the standard.
1.6This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
| Committee |
F 17
|
| DocumentType |
Guide
|
| Pages |
2
|
| ProductNote |
Reconfirmed 2016
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| ASTM F 2968/F2968M : 2014 : REV A | Standard Specification for Black Crosslinked Polyethylene (PEX) Pipe, Fittings and Joints For Gas Distribution Applications |
| ASTM F 1563 : 2001 : R2011 | Standard Specification for Tools to Squeeze-off Polyethylene (PE) Gas Pipe or Tubing |
| ASTM F 1025 : 1994 : R2011 | Standard Guide for Selection and Use of Full-Encirclement-Type Band Clamps for Reinforcement or Repair of Punctures or Holes in Polyethylene Gas Pressure Pipe |
| ASTM F 2818 : 2010 : R2014 : EDT 1 | Standard Specification for Specification for Crosslinked Polyethylene (PEX) Material Gas Pressure Pipe and Tubing |
| ASTM F 1734 : 2019 | Standard Practice for Qualification of a Combination of Squeeze Tool, Pipe, and Squeeze-Off Procedures to Avoid Long-Term Damage in Polyethylene (PE) Gas Pipe |
| ASTM D 2513 : 2006 | Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2513 : 2016 | Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2513 : 2003 : REV A | Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2513 : 2012 : REV A | Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2513 : 2008 : REV A | Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2513 : 2011 : REV B | Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2513 : 2006 : REV A | Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2513 : 2009 | Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2513 : 2004 | Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2513 : 1987 | Standard Specification for Thermoplastic Gas Pressure Piping Systems |
| ASTM D 2513 : 2011 : REV C | Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings |
| ASTM F 1734 : 2003 : R2009 | Standard Practice for Qualification of a Combination of Squeeze Tool, Pipe, and Squeeze-Off Procedures to Avoid Long-Term Damage in Polyethylene (PE) Gas Pipe (Withdrawn 2018) |
| ASTM D 2513 : 2016 : REV A | Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2513 : 2013 | Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2513 : 1999 | Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings |
| ASTM F 1734 : 2019 | Standard Practice for Qualification of a Combination of Squeeze Tool, Pipe, and Squeeze-Off Procedures to Avoid Long-Term Damage in Polyethylene (PE) Gas Pipe |
| ASTM D 2513 : 2009 : REV A | Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2513 : 2003 : REV B | Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2513 : 2001 : REV A | Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2513 : 2001 | Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2513 : 2001 : REV A : EDT 1 | Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2513 : 2011 : EDT 1 | Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2513 : 2014 : EDT 1 | Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2513 : 2014 | Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2513 : 2000 | Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2513 : 2007 : REV A | Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2513 : 2019 | Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2513 : 2011 | Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2513 : 2008 : REV B | Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2513 : 2017-01 | SPECIFICATION FOR POLYETHYLENE (PE) GAS PRESSURE PIPE, TUBING, AND FITTINGS |
| ASTM D 2513 : 2003 | Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2513 : 2006 : REV B | Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings |
| ASTM F 1734 : 2003 | Standard Practice for Qualification of a Combination of Squeeze Tool, Pipe, and Squeeze-Off Procedures to Avoid Long-Term Damage in Polyethylene (PE) Gas Pipe |
| ASTM D 2513 : 2007 : REV B : EDT 1 | Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2513 : 2008 | Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2513 : 2018 : REV A | Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2513 : 2007 | Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2513 : 2007 : REV B | Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2513 : 2012 : REV A : EDT 1 | Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2513 : 2018 | Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2513 : 2011 : REV A | Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2513 : 2012 | Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings |
| ASTM F 1734 : 1996 | Standard Practice for Qualification of a Combination of Squeeze Tool, Pipe, and Squeeze-Off Procedures to Avoid Long-Term Damage in Polyethylene (PE) Gas Pipe |
| ASTM D 2513 : 2004 : REV A | Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2513 : 2005 | Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.