THREADED PIPE FITTING IN MALLEABLE CAST IRON

Amended by

DIN EN 10242/A2:2003-06

Available format(s)

Hardcopy , PDF

Published date

01-01-1995

Publisher

German Institute for Standardisation (Deutsches Institut für Normung)

Vorwort
1 Anwendungsbereich
2 Normative Verweisungen
3 Fittingstypen
4 Begriffe und Definitionen
5 Werkstoffe
6 Konstruktion
7 Masse und Toleranzen
8 Gewinde
9 Herstellung
10 Eigenschaften
11 Prüfung und Kontrolle
12 Qualitätssicherungssystem
13 Bezeichnung der Fittings
14 Kennzeichnung
Tabellen der masslich genormten Fittingstypen und
Grössen (Tabellen 8 bis 26)
Anhang A (normativ) Tempergussfittings für
         Gewindeverbindungen nach ISO 7-1, jedoch mit
         Innengewinde Rc
Anhang B (informativ) Qualitätssicherungssystem und
         Bewertung der Konformität
Anhang C (informativ) Zusammenhang mit den
         wesentlichen Anforderungen der
         Bauproduktenrichtlinie (89/106 EG)
Anhang D (informativ) Zusammenhang zwischen
         Fittinggrösse und Nennweite (DN)
Anhang E (informativ) Literaturhinweise

This standard is included in DIN HDBK 15-6. Specifies the requirements for the design and performance of threaded pipe fittings in malleable cast iron.

DevelopmentNote	Supersedes DIN 2950 (07/2002)
DocumentType	Standard
Pages	46
ProductNote	NEW CHILD AMD 2 IS NOW ADDED
PublisherName	German Institute for Standardisation (Deutsches Institut für Normung)
Status	Current
Supersedes	DIN 2950:1983-04

Standards	Relationship
UNE-EN 10242:1995	Identical
I.S. EN 10242:1995	Identical
NS EN 10242 : 94 AMD 2 2003	Identical
NEN EN 10242 : 1995 AMD 2 2003	Identical
NBN EN 10242 : 95 AMD 2 2003	Identical
BS EN 10242:1995	Identical
UNI EN 10242 : 2009	Identical
NF EN 10242 : 95 AMD 2 2004	Identical
SN EN 10242 : 1995 AMD 2 2003	Identical
EN 10242:1994/A2:2003	Identical

DIN HDBK 15-6 : 1ED 2012
DIN 1988-600:2010-12	Codes of practice for drinking water installations - Part 600: Drinking water installations in connection with fire fighting and fire protection installations; DVGW code of practice
BWB TL 4240-0072 : 1ED 2008	RESCUE AND RECOVERY EQUIPMENT, LIGHT
DIN 1988-200:2012-05	Codes of practice for drinking water installations - Part 200: Installation Type A (closed system) - Planning, components, apparatus, materials; DVGW code of practice
DIN 50930-6:2013-10	Corrosion of metals - Corrosion of metallic materials under corrosion load by water inside of pipes, tanks and apparatus - Part 6: Evaluation process and requirements regarding the hygienic suitability in contact with drinking water
DIN 30690-1:2016-04	CONSTRUCTION ELEMENTS IN THE GAS SUPPLY SYSTEM - PART 1: REQUIREMENTS FOR CONSTRUCTION ELEMENTS IN GAS SUPPLY SYSTEMS
DIN 14462:2012-09	Water conduit for fire extinguishing - Planning, installation, operation and maintenance of fire hose systems and pillar fire hydrant and underground fire systems
DIN 1988-7:2004-12	CODES OF PRACTICE FOR DRINKING WATER INSTALLATIONS (TRWI) - PART 7: PREVENTION OF CORROSION DAMAGE AND CALCAREOUS DEPOSIT FORMATION - DVGW CODE OF PRACTICE

EN 29002 : 1994	QUALITY SYSTEMS - MODEL FOR QUALITY ASSURANCE IN PRODUCTION & INSTALLATION
DIN ISO 228-2:1988-07	PIPE THREADS WHERE PRESSURE-TIGHT JOINTS ARE NOT MADE ON THE THREADS - VERIFICATION BY MEANS OF LIMIT GAUGES
ISO 2859:1974	Sampling procedures and tables for inspection by attributes
DIN ISO 2859-1:2014-08	SAMPLING PROCEDURES FOR INSPECTION BY ATTRIBUTES - PART 1: SAMPLING SCHEMES INDEXED BY ACCEPTANCE QUALITY LIMIT (AQL) FOR LOT-BY-LOT INSPECTION (ISO 2859-1:1999 + COR. 1:2001 + AMD.1:2011)
EN 1562:2012	Founding - Malleable cast irons
DIN ISO 228-1:1994-12	PIPE THREADS WHERE PRESSURE-TIGHT JOINTS ARE NOT MADE ON THE THREADS - PART 1: DIMENSIONS, TOLERANCES AND DESIGNATION
PREN 1562 : DRAFT 2009	FOUNDING - MALLEABLE CAST IRONS
EN ISO 9002:1994/AC:1997	QUALITY SYSTEMS - SPECIFICATION FOR PRODUCTION AND INSTALLATION
ISO 7-2:2000	Pipe threads where pressure-tight joints are made on the threads Part 2: Verification by means of limit gauges
ISO 6708:1995	Pipework components Definition and selection of DN (nominal size)
DIN 50049:1992-04	METALLIC PRODUCTS; TYPES OF INSPECTION DOCUMENTS
ISO 2859-2:1985	Sampling procedures for inspection by attributes — Part 2: Sampling plans indexed by limiting quality (LQ) for isolated lot inspection
ISO 2859-0:1995	Sampling procedures for inspection by attributes — Part 0: Introduction to the ISO 2859 attribute sampling system
DIN 2999-1:1983-07	PIPE THREADS FOR TUBES AND FITTINGS - PARALLEL INTERNAL THREAD AND TAPER EXTERNAL THREAD - TREAD DIMENSIONS
DIN 50988-1:1984-02	MEASUREMENT OF COATING THICKNESS; DETERMINATION OF THE MASS PER UNIT AREA OF ZINC- AND TIN-COATINGS ON FERROUS MATERIALS BY DISSOLUTION OF THE COATING MATERIAL; GRAVIMETRIC METHOD
ISO 9002:1994	Quality systems — Model for quality assurance in production, installation and servicing
EN ISO 6708:1995	Pipework components - Definition and selection of DN (nominal size) (ISO 6708:1995)
EN ISO 228-1:2003	Pipe threads where pressure-tight joints are not made on the threads - Part 1: Dimensions, tolerances and designation (ISO 228-1:2000)
ISO 7-1:1994	Pipe threads where pressure-tight joints are made on the threads Part 1: Dimensions, tolerances and designation
EN ISO 9001:2015	Quality management systems - Requirements (ISO 9001:2015)
DIN EN 26708 : 1993
EN 10204:2004	Metallic products - Types of inspection documents
ISO 9001:2015	Quality management systems — Requirements
ISO 2178:2016	Non-magnetic coatings on magnetic substrates Measurement of coating thickness Magnetic method
DIN EN ISO 9001:2015-11	QUALITY MANAGEMENT SYSTEMS - REQUIREMENTS (ISO 9001:2015)
ISO 1460:1992	Metallic coatings Hot dip galvanized coatings on ferrous materials Gravimetric determination of the mass per unit area
EN 45012 : 1998	GENERAL REQUIREMENTS FOR BODIES OPERATING ASSESSMENT AND CERTIFICATION/REGISTRATION OF QUALITY SYSTEMS
EN 29001 : 1994	QUALITY SYSTEMS - MODEL FOR QUALITY ASSURANCE IN DESIGN/DEVELOPMENT, PRODUCTION, INSTALLATION & SERVICING
ISO 228-1:2000	Pipe threads where pressure-tight joints are not made on the threads Part 1: Dimensions, tolerances and designation

View more information

US$144.05

Excluding Tax where applicable

Product format

I agree to the DRM document license rules apply against the PDF selection made.

Please confirm that you agree to the document license rules for this document.

I agree to the document license rules .

Please confirm that you agree to the document license rules for this document.

Access your standards online with a subscription

Features

Simple online access to standards, technical information and regulations.
Critical updates of standards and customisable alerts and notifications.
Multi-user online standards collection: secure, flexible and cost effective.

Learn more on subscription solutions

Get in touch with us

DIN EN 10242:1995-03

THREADED PIPE FITTING IN MALLEABLE CAST IRON

Table of Contents

Abstract

General Product Information

International Equivalents

Standards Referenced By This Book

Standards Referencing This Book

Category

Subcategory