• DIN EN ISO 12215-5:2014-10

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    Add to Watchlist
    This Standard has been added successfully to your Watchlist.
    Please visit My Watchlist to see all standards that you are watching.
    Please log in or to add this standard to your Watchlist.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    You have already added this standard to your Watchlist.
    Visit My Watchlist to view the full list.

    SMALL CRAFT - HULL CONSTRUCTION AND SCANTLINGS - PART 5: DESIGN PRESSURES FOR MONOHULLS, DESIGN STRESSES, SCANTLINGS DETERMINATION (ISO 12215-5:2008 + AMD 1:2014)

    Available format(s):  Hardcopy, PDF

    Superseded date:  07-08-2019

    Language(s):  German

    Published date:  01-12-2013

    Publisher:  German Institute for Standardisation (Deutsches Institut für Normung)

    Add to Watchlist

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    National foreword
    National Annex NA (informative) - Bibliography
    Foreword
    Foreword to EN ISO 12215-5:2008/A1:2014
    Introduction
    1 Scope
    2 Normative references
    3 Terms and definitions
    4 Symbols
    5 General
    6 Dimensions, data and areas
    7 Pressure adjusting factors
    8 Design pressures
    9 Dimensions of panels and stiffeners
    10 Plating - Scantling equations
    11 Stiffening members requirements
    12 Owner's manual
    Annex A (normative) - Simplified method for
            scantling determination
    Annex B (normative) - Drop test for boats of < 6m
    Annex C (normative) - FRP laminates properties
            and calculations
    Annex D (normative) - Sandwich mechanical core
            properties and sandwich calculation
    Annex E (normative) - Wood laminate properties
            and wood calculations
    Annex F (normative) - Mechanical properties of
            metals
    Annex G (normative) - Geometric properties of
            stiffeners
    Annex H (normative) - Laminate stack analysis
    Bibliography

    Abstract - (Show below) - (Hide below)

    Pertains to the determination of design pressures and stresses, and to the determination of the scantlings, including internal structural members of monohull small craft constructed from fibre-reinforced plastics, aluminium or steel alloys, glued wood or other suitable boat building material, with a length of hull, L[H], in accordance with ISO 8666, between 2,5 m and 24 m.

    General Product Information - (Show below) - (Hide below)

    Document Type Standard
    Publisher German Institute for Standardisation (Deutsches Institut für Normung)
    Status Superseded
    Superseded By

    Standards Referencing This Book - (Show below) - (Hide below)

    ISO 1922:2012 Rigid cellular plastics Determination of shear strength
    ISO 12215-9:2012 Small craft Hull construction and scantlings Part 9: Sailing craft appendages
    DIN EN ISO 8666 E : 2003 SMALL CRAFT - PRINCIPAL DATA (ISO 8666:2016)
    ISO 845:2006 Cellular plastics and rubbers Determination of apparent density
    BS EN 408 : 2010 TIMBER STRUCTURES - STRUCTURAL TIMBER AND GLUED LAMINATED TIMBER - DETERMINATION OF SOME PHYSICAL AND MECHANICAL PROPERTIES
    ASTM C 393 : 2000 Standard Test Method for Flexural Properties of Sandwich Constructions
    ISO 8666:2016 Small craft Principal data
    DIN EN ISO 527-2:2012-06 Plastics - Determination of tensile properties - Part 2: Test conditions for moulding and extrusion plastics (ISO 527-2:2012)
    DIN EN ISO 178 E : 2013 PLASTICS - DETERMINATION OF FLEXURAL PROPERTIES (ISO 178:2010 + AMD.1:2013)
    ISO 527-2:2012 Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and extrusion plastics
    DIN EN ISO 845 E : 2009 CELLULAR PLASTICS AND RUBBERS - DETERMINATION OF APPARENT DENSITY
    ISO 12215-3:2002 Small craft — Hull construction and scantlings — Part 3: Materials: Steel, aluminium alloys, wood, other materials
    DIN EN ISO 844:2014-11 Rigid cellular plastics - Determination of compression properties (ISO 844:2014)
    DIN EN ISO 844 E : 2014 RIGID CELLULAR PLASTICS - DETERMINATION OF COMPRESSION PROPERTIES (ISO 844:2014)
    EN 13195-1 : 2002 ALUMINIUM AND ALUMINIUM ALLOYS - WROUGHT AND CAST PRODUCTS FOR MARINE APPLICATIONS (SHIPBUILDING, MARINE AND OFFSHORE) - PART 1: SPECIFICATIONS
    DIN EN ISO 8666:2003-04 SMALL CRAFT - PRINCIPAL DATA (ISO 8666:2016)
    DIN EN ISO 527-1:2012-06 PLASTICS - DETERMINATION OF TENSILE PROPERTIES - PART 1: GENERAL PRINCIPLES (ISO 527-1:2012)
    ISO 12216:2002 Small craft Windows, portlights, hatches, deadlights and doors Strength and watertightness requirements
    ISO 178:2010 Plastics Determination of flexural properties
    ISO 844:2014 Rigid cellular plastics Determination of compression properties
    BS EN 1995-1-1 : 2012 EUROCODE 5: DESIGN OF TIMBER STRUCTURES - PART 1-1: GENERAL - COMMON RULES AND RULES FOR BUILDINGS
    ISO 12215-6:2008 Small craft — Hull construction and scantlings — Part 6: Structural arrangements and details
    ISO 527-1:2012 Plastics Determination of tensile properties Part 1: General principles
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective