Customer Support: +1 416-401-8730

Login to i2i Subscription Intertek.com
  • There are no items in your cart
Please enter a keyword to search
Advanced search
Home
CEN
EN ISO 23210:2009

EN ISO 23210:2009

Current

Current

The latest, up-to-date edition.

Stationary source emissions - Determination of PM10/PM2,5 mass concentration in flue gas - Measurement at low concentrations by use of impactors (ISO 23210:2009)

Published date

08-01-2009

Publisher

Comite Europeen de Normalisation

Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols and abbreviated terms
5 Principle of the method
6 Specification of the two-stage impactor
7 Sampling train
8 Preparation, measurement procedure and
   post-treatment
9 Calculation of the results
10 Performance characteristics
11 Reporting
Annex A (normative) - Calculation of the sample
                      volumetric flow rate of the
                      impactor
Annex B (informative) - General equations concerning
                        impaction theory
Annex C (informative) - Results of method validation
Annex D (informative) - Influence of variations in
                        the flue gas temperature and
                        flue gas composition on the
                        Reynolds number
Annex E (informative) - Entry nozzle
Annex F (informative) - Equipment list
Annex G (normative) - Determination of a representative
                      sampling point
Bibliography

ISO 23210:2009 specifies a standard reference method for the determination of PM10 and PM2,5 mass concentrations at stationary emission sources by use of two-stage impactors. The measurement method is especially suitable for measurements of mass concentrations below 40 mg/m3 as half-hourly averages in standard conditions (273 K, 1 013 hPa, dry gas). It is an acceptable method for the measurement in the flue gas of different installations, such as cement and steel production plants, as well as combustion processes.ISO 23210:2009 is not applicable to the sampling of flue gases that are saturated with water vapour.ISO 23210:2009 is not applicable where the majority of the particles are likely to exceed PM10, for example, in the case of raw gases or plant operating failures.ISO 23210:2009 cannot be used for the determination of the total mass concentration of dust.ISO 23210:2009 describes the design, use and theory of round-nozzle impactors. It does not exclude other types of impactors, provided these systems meet the performance criteria specified in ISO 23210:2009 in a validation of the impactor performed by an independent testing laboratory.

Committee
CEN/TC 264
DocumentType
Standard
PublisherName
Comite Europeen de Normalisation
Status
Current

VDI 3803 Blatt 4:2012-09 Air-conditioning, system requirements - Air filter systems (VDI Ventilation Code of Practice)
VDI 3461:2016-09 (Draft) Emission control - Thermochemical gasification of biomass in cogeneration
VDI 2286 Blatt 1:2013-08 Emission control - Electrolytic aluminium reduction process
VDI 3476 Blatt 1:2015-06 Waste gas cleaning - Methods of catalytic waste gas cleaning - Fundamentals
VDI 4300 Blatt 11:2013-12 Measurement of indoor air pollution - Measurement strategies for determination of airborne particles in indoor environment - PM-fraction
VDI 2441:2016-05 Process gas and waste gas cleaning by cold plasma - Barrier discharge, corona discharge, UV radiation
VDI 2578:2017-05 Emission control - Glassworks
VDI 2095 Blatt 1:2011-03 Emission control - Treatment of mineral construction-site and demolition waste - Stationary and mobile demolition waste recycling facilities
VDI 3475 Blatt 5:2015-10 Emission control - Biological waste treatment facilities - Anaerobic digestion and post-treatment
VDI 3477:2016-03 Biological waste gas purification - Biofilters
S.R. CWA 16060:2009 ENVIRONMENTAL TECHNOLOGY VERIFICATION - AIR EMISSION ABATEMENT TECHNOLOGIES
UNE-CWA 16060:2010 IN Environmental technology verification - Air emission abatement technologies

ISO/IEC 17025:2005 General requirements for the competence of testing and calibration laboratories
ISO 12141:2002 Stationary source emissions — Determination of mass concentration of particulate matter (dust) at low concentrations — Manual gravimetric method
ISO 7708:1995 Air quality — Particle size fraction definitions for health-related sampling
ISO 4225:1994 Air quality General aspects Vocabulary
ISO 14956:2002 Air quality Evaluation of the suitability of a measurement procedure by comparison with a required measurement uncertainty
EN 15259:2007 Air quality - Measurement of stationary source emissions - Requirements for measurement sections and sites and for the measurement objective, plan and report
EN 13284-1:2017 Stationary source emissions - Determination of low range mass concentration of dust - Part 1: Manual gravimetric method
ISO 20988:2007 Air quality Guidelines for estimating measurement uncertainty

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Learn more on subscription solutions

or

Get in touch with us