JIS Z 9015:1980

1. Scope2. Definitions and Symbols 2.1 Definitions 2.2 Symbols3. Inspection Procedure4. Operation of Inspection 4.1 Establishment of Quality Criteria 4.2 Classification of Defects or Defectives 4.3 Designation of AQL 4.4 Designation of Inspection Level 4.5 Selection of Type of Inspection 4.6 Designation of Inspection Severity 4.7 Formation of Lot 4.8 Selection of Sampling Inspection Plans 4.8.1. Sample Size Code Letters 4.8.2. Case of Single Sampling Inspection 4.8.3. Case of Double Sampling Inspection 4.8.4. Case of Multiple Sampling Inspection Plan 4.9 Taking Sample 4.10 Test of Sample 4.11 Determination of Lot Acceptability 4.11.1 Classes of Defects or Defectives and Determination of Acceptability 4.11.2 Case of Single Sampling Inspection for Percent Defective 4.11.3 Case of Double Sampling Inspection for Percent Defective 4.11.4 Case of Multiple Sampling Inspection for Percent Defective 4.11.5 Case of Sampling Inspection for Defects per One Hundred Units 4.11.6 Special Procedure 4.12 Disposition of Lot 4.13 Resubmitting Rejected Lot 4.14 Special Measures for Critical Defects5. Adjustment of Inspection Severity 5.1 General Items 5.1.1 Necessity for Adjusting Severity of Inspection 5.1.2 Adjustment for Severity for Classes of Defects or defective 5.1.3 Time of Adjusting Severity 5.1.4. Exclusion of Resubmitted Lot 5.2 First Inspection and subsequent Inspection 5.2.1 First Inspection 5.5.2 Subsequent Inspection 5.3 Switching Procedures 5.3.1 Change from Normal Inspection to Tightened Inspection 5.3.2 Change from Tightened Inspection to Normal Inspection 5.3.3 Change from Normal Inspection to Reduced Inspection 5.3.4 Change from Reduced Inspection to Normal Inspection 5.4 Discontinuation of InspectionAttached Table 1 Sample Size Code LettersAttached Table 2-A Single Sampling Plans for Normal Inspection (Master Table)Attached Table 2-B Single Inspection Plans for Tightened Inspection (Master Table)Attached Table 2-C Single Inspection Plans for Reduced Inspection (Master Table)Attached Table 3-A Double Sampling Plans for Normal Inspection (Master Table)Attached Table 3-B Double Sampling Plans for Tightened Inspection (Master Table)Attached Table 3-C Double Sampling Plans for Reduced Inspection (Master Table)Attached Table 4-A Multiple Sampling Plans for Normal Inspection (Master Table)Attached Table 4-B Multiple Sampling Plans for Tightened Inspection (Master Table)Attached Table 4-C Multiple Sampling Plans for Reduced Inspection (Master Table)Attached Table 5-A Limit Numbers for Tightened InspectionAttached Table 5-B Limit Numbers for Reduced InspectionAttached Fig. 1-A OC Curves for Normal InspectionAttached Fig. 1-B OC Curves for Normal InspectionAttached Fig. 1-C OC Curves for Normal InspectionAttached Fig. 2-A OC Curves for Tightened InspectionAttached Fig. 2-B OC Curves for Tightened InspectionAttached Fig. 2-C OC Curves for Tightened InspectionAttached Fig. 3-A OC Curves for Reduced InspectionAttached Fig. 3-B OC Curves for Reduced InspectionAttached Fig. 3-C OC Curves for Reduced InspectionAttached Fig. 3-D OC Curves for Reduced InspectionAttached Fig. 3-E OC Curves for Reduced Inspection