NF EN 10113-3 : 1993

Superseded

PRODUITS LAMINES A CHAUD EN ACIERS DE CONSTRUCTION SOUDABLES A GRAINS FINS - PARTIE 3: CONDITIONS DE LIVRAISON DES ACIERS OBTENUS PAR LAMINAGE THERMOMECANIQUE

Superseded date

03-01-2005

Published date

01-12-2013

Publisher

Association Francaise de Normalisation

Cooperating organizations
National foreword
Foreword
1 Scope
2 Normative references
3 Definitions
4 Information to be supplied by the purchaser
4.1 General
4.2 Options
5 Dimensions, mass and tolerances
5.1 Dimensions and tolerances
5.2 Mass of steel
6 Classification of qualities; designation
6.1 Classification of qualities
6.2 Designation
7 Technical requirements
7.1 Steel manufacturing process
7.2 Delivery condition
7.3 Chemical composition
7.4 Mechanical properties
7.5 Technological properties
7.6 Surface finish
7.7 Internal defects
8 Inspection and testing
8.1 General
8.2 Sampling
8.3 Test units
8.4 Verification of chemical composition
8.5 Mechanical tests
8.6 Test methods
8.7 Retests and resubmission for testing
8.8 Inspection documents
9 Marking for flat and long products
10 Complaints after delivery
11 Options
11.1 All products
11.2 Flat products
11.3 Long products
National annex NA (informative) Committees responsible

Specifies requirements for flat products with nominal thickness less than or equal to 63 mm and long products with nominal thickness less than or equal to 150 mm of hot-rolled weldable fine grain structural steel in the thermomechanical rolled condition. Includes sections on definitions, technical requirements, and inspection and testing.

DevelopmentNote	INDICE DE CLASSEMENT: A35505-3
DocumentType	Standard
PublisherName	Association Francaise de Normalisation
Status	Superseded

Standards	Relationship
BS EN 10113-3:1993	Identical
DIN EN 10113-3:1993-04	Identical
UNE-EN 10113-3:1994	Identical
I.S. EN 10113-3:1993	Identical
EN 10113-3 : 1993	Identical

XP ENV 13381-4 : 2002 XP	TEST METHODS FOR DETERMINING THE CONTRIBUTION TO THE FIRE RESISTANCE OF STRUCTURAL MEMBERS - PART 4: APPLIED PROTECTION TO STEEL MEMBERS
NFP 22 501-1 : 98 XP	EXECUTION OF STEEL STRUCTURES - PART 1: GENERAL RULES AND RULES FOR BUILDINGS
NFP 22 311 : 92 AMD 2 2002 XP	STEEL CONSTRUCTION - EUROCODE 3: "DESIGN OF STEEL STRUCTURES" AND NATIONAL APPLICATION DOCUMENT - PART 1-1: GENERAL RULES AND RULES FOR BUILDINGS
XP ENV 13381-2 : 2002 XP	TEST METHODS FOR DETERMINING THE CONTRIBUTION TO THE FIRE RESISTANCE OF STRUCTURAL MEMBERS - PART 2: VERTICAL PROTECTIVE MEMBRANES
NFP 98 550 : 96 XP	VERTICAL ROAD TRAFFIC SIGNS - GANTRIES, CANTILEVERS AND HIGH MASTS - CALCULATION SPECIFICATIONS, INSTALLATION AND CONTROL
NF CEN/TS 13001-3-1 : 2005 XP	CRANES - GENERAL DESIGN - PART 3-1: LIMIT STATES AND PROOF OF COMPETENCE OF STEEL STRUCTURES
FD CR 10313 : 2000 FD	CLASSIFICATION OF GRADES OF STEEL - EXAMPLES OF CLASSIFICATION RELATED TO EUROPEAN STANDARDS
NF ENV 1993 1-3 : 99 XP	STEEL CONSTRUCTION - EUROCODE 3: DESIGN OF STEEL STRUCTURES AND NATIONAL APPLICATION DOCUMENT - PART 1-3: GENERAL RULES - SUPPLEMENTARY RULES FOR COLD FORMED THIN GAUGE MEMBERS AND SHEETING