We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
  • ASTM D 5485 : 2021

    Current The latest, up-to-date edition.
    Add to Watchlist
    This Standard has been added successfully to your Watchlist
    Please visit My Watchlist to see all standards that you are watching.
    Please log in or to add this standard to your Watchlist.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    You have already added this standard to your Watchlist.
    Visit My Watchlist to view the full list.

    Standard Test Method for Determining Corrosive Effect of Combustion Products Using the Cone Corrosimeter

    Available format(s):  Hardcopy, PDF

    Language(s):  English

    Published date:  11-05-2021

    Publisher:  American Society for Testing and Materials

    Add to Watchlist

    Add To Cart

    Scope - (Show below) - (Hide below)

    1.1This fire-test-response standard measures the corrosive effect by loss of metal from the combustion products of materials, components, or products.

    1.2This test method provides corrosion results of product and material specimens limited to a maximum size of 100 by 100 mm in area and 50 mm thick.

    1.3Additional information regarding the targets, the test conditions, and test limitations is provided in Annex A1.

    1.4The results of this test method have not been investigated with respect to correlation to actual fires.

    1.5An ISO standard exists, as developed by ISO TC 61 (Plastics), subcommittee 4 (on burning behavior), which is technically very similar to this test method and is designated ISO 11907-4.

    1.6The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. (See IEEE/ASTM SI10.)

    1.7This standard measures and describes the response of materials, products, or assemblies to heat and flame under controlled conditions, but does not by itself incorporate all factors required for fire hazard or fire risk assessment of the materials, products, or assemblies under actual fire conditions.

    1.8Fire testing is inherently hazardous. Adequate safeguards for personnel and property shall be employed in conducting these tests.

    1.9This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see Section 7.

    1.10This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

    General Product Information - (Show below) - (Hide below)

    Committee D 09
    Document Type Test Method
    Publisher American Society for Testing and Materials
    Status Current
    Supersedes

    Standards Referencing This Book - (Show below) - (Hide below)

    ASTM E 176 : 2018 : REV A : EDT 1 Standard Terminology of Fire Standards
    ASTM E 1354 : 2022 Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter
    ASTM E 176 : 2021 Standard Terminology of Fire Standards
    ASTM E 906/E906M : 2021 Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using a Thermopile Method
    ASTM E 176 : 2018 : REV A : EDT 2 Standard Terminology of Fire Standards
    ASTM E 1354 : 2017 Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter
    ASTM D 618 : 2013 Standard Practice for Conditioning Plastics for Testing
    ASTM E 906/E906M : 2017 Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using a Thermopile Method
    ASTM E 1354 : 2022 : REV A Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter
    ASTM E 176 : 2021 : REV A Standard Terminology of Fire Standards
    ASTM D 618 : 2021 Standard Practice for Conditioning Plastics for Testing
    ASTM D 6113 : 2021 Standard Test Method for Using Cone Calorimeter to Determine Fire-Test-Response Characteristics of Insulating Materials Contained in Electrical or Optical Fiber Cables
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective