ASTM D 8239 : 2018
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Standard Specification for Performance-Graded Asphalt Binder Using the Multiple Stress Creep and Recovery (MSCR) Test
Hardcopy , PDF
09-02-2021
English
10-12-2018
This specification2 covers asphalt binders graded by performance.
1.1 This specification2 covers asphalt binders graded by performance. Grading designations are related to the LTPPBind calculated maximum pavement design temperature, the minimum pavement design temperature, and the traffic loading.
1.2This specification incorporates Test Method D7405 for determining non-recoverable creep compliance, Jnr. “S,” “H,” “V,” or “E” designations must be specified for standard, high, very high, and extremely high traffic loading, respectively.
1.3The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.4The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.
Note 1:A guidance document for specifying bodies using R % for elastic properties is under development.
Note 2:For asphalt binders graded by penetration at 25 °C, see Specification D946/D946M. For asphalt binders graded by viscosity at 60 °C, see Specification D3381/D3381M. For performance-graded asphalt binder, see Specification D6373.
Note 3:AASHTO R 29 provides non-mandatory information for determining the performance grade of an asphalt binder.
1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| Committee |
D 04
|
| DocumentType |
Standard
|
| Pages |
6
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy |
| ASTM D 4552/D4552M : 2020 | Standard Classification for Hot-Mix Recycling Agents |
| ASTM D 6373 : 2013 | Standard Specification for Performance Graded Asphalt Binder |
| ASTM D 6723 : 2012 | Standard Test Method for Determining the Fracture Properties of Asphalt Binder in Direct Tension (DT) (Withdrawn 2021) |
| ASTM D 6521 : 2018 | Standard Practice for Accelerated Aging of Asphalt Binder Using a Pressurized Aging Vessel (PAV) |
| ASTM D 2042 : 2001 | Standard Test Method for Solubility of Asphalt Materials in Trichloroethylene |
| ASTM D 6521 : 2019 : REV A | Standard Practice for Accelerated Aging of Asphalt Binder Using a Pressurized Aging Vessel (PAV) |
| ASTM D 6648 : 2008 : R2016 | Standard Test Method for Determining the Flexural Creep Stiffness of Asphalt Binder Using the Bending Beam Rheometer (BBR) |
| ASTM D 2872 : 2019 | Standard Test Method for Effect of Heat and Air on a Moving Film of Asphalt (Rolling Thin-Film Oven Test) |
| ASTM D 6521 : 2008 | Standard Practice for Accelerated Aging of Asphalt Binder Using a Pressurized Aging Vessel (PAV) |
| ASTM D 7405 : 2015 | Standard Test Method for Multiple Stress Creep and Recovery (MSCR) of Asphalt Binder Using a Dynamic Shear Rheometer |
| ASTM D 6373 : 1999 | Standard Specification for Performance Graded Asphalt Binder |
| ASTM D 6373 : 2016 | Standard Specification for Performance Graded Asphalt Binder |
| ASTM D 7553 : 2015 | Standard Test Method for Solubility of Asphalt Materials in N-Propyl Bromide |
| ASTM D 5546 : 2001 | Standard Test Method for Solubility of Asphalt Binders in Toluene by Centrifuge |
| ASTM D 2042 : 1997 | Standard Test Method for Solubility of Asphalt Materials in Trichloroethylene |
| ASTM D 7175 : 2005 | Standard Test Method for Determining the Rheological Properties of Asphalt Binder Using a Dynamic Shear Rheometer |
| ASTM D 6723 : 2001 | Standard Test Method for Determining the Fracture Properties of Asphalt Binder in Direct Tension (DT) |
| ASTM D 6648 : 2008 | Standard Test Method for Determining the Flexural Creep Stiffness of Asphalt Binder Using the Bending Beam Rheometer (BBR) |
| ASTM D 6521 : 2013 | Standard Practice for Accelerated Aging of Asphalt Binder Using a Pressurized Aging Vessel (PAV) |
| ASTM D 5546 : 1994 : REV A | Standard Test Method for Solubility of Asphalt Binders in Toluene by Centrifuge |
| ASTM D 2042 : 2009 | Standard Test Method for Solubility of Asphalt Materials in Trichloroethylene |
| ASTM D 7175 : 2007 | Standard Test Method for Determining the Rheological Properties of Asphalt Binder Using a Dynamic Shear Rheometer |
| ASTM D 7175 : 2005 : EDT 1 | Standard Test Method for Determining the Rheological Properties of Asphalt Binder Using a Dynamic Shear Rheometer |
| ASTM D 2872 : 2012 : EDT 1 | Standard Test Method for Effect of Heat and Air on a Moving Film of Asphalt (Rolling Thin-Film Oven Test) |
| ASTM D 2042 : 2015 | Standard Test Method for Solubility of Asphalt Materials in Trichloroethylene |
| ASTM D 7553 : 2009 | Standard Test Method for Solubility of Asphalt Materials in N-Propyl Bromide |
| ASTM D 7175 : 2008 | Standard Test Method for Determining the Rheological Properties of Asphalt Binder Using a Dynamic Shear Rheometer |
| ASTM D 7405 : 2008 | Standard Test Method for Multiple Stress Creep and Recovery (MSCR) of Asphalt Binder Using a Dynamic Shear Rheometer |
| ASTM D 7553 : 2010 | Standard Test Method for Solubility of Asphalt Materials in N-Propyl Bromide |
| ASTM D 7405 : 2020 | Standard Test Method for Multiple Stress Creep and Recovery (MSCR) of Asphalt Binder Using a Dynamic Shear Rheometer |
| ASTM D 2872 : 2012 | Standard Test Method for Effect of Heat and Air on a Moving Film of Asphalt (Rolling Thin-Film Oven Test) |
| ASTM D 8 : 2021 | Standard Terminology Relating to Materials for Roads and Pavements |
| ASTM D 7405 : 2010 : REV A | Standard Test Method for Multiple Stress Creep and Recovery (MSCR) of Asphalt Binder Using a Dynamic Shear Rheometer <a href="#fn00002"></a> |
| ASTM D 6521 : 2005 | Standard Practice for Accelerated Aging of Asphalt Binder Using a Pressurized Aging Vessel (PAV) |
| ASTM D 7405 : 2010 | Standard Test Method for Multiple Stress Creep and Recovery (MSCR) of Asphalt Binder Using a Dynamic Shear Rheometer <a href="#fn00002"></a> |
| ASTM D 6373 : 2007 : EDT 1 | Standard Specification for Performance Graded Asphalt Binder |
| ASTM D 7405 : 2008 : REV A | Standard Test Method for Multiple Stress Creep and Recovery (MSCR) of Asphalt Binder Using a Dynamic Shear Rheometer <a href="#fn00002"></a> |
| ASTM D 6521 : 2004 | Standard Practice for Accelerated Aging of Asphalt Binder Using a Pressurized Aging Vessel (PAV) |
| ASTM D 6373 : 2015 | Standard Specification for Performance Graded Asphalt Binder |
| ASTM D 6521 : 2003 : REV A | Standard Practice for Accelerated Aging of Asphalt Binder Using a Pressurized Aging Vessel (PAV) |
| ASTM D 7175 : 2015 | Standard Test Method for Determining the Rheological Properties of Asphalt Binder Using a Dynamic Shear Rheometer |
| ASTM D 6521 : 2000 | Standard Practice for Accelerated Aging of Asphalt Binder Using a Pressurized Aging Vessel (PAV) |
| ASTM D 2872 : 1997 | Standard Test Method for Effect of Heat and Air on a Moving Film of Asphalt (Rolling Thin-Film Oven Test) |
| ASTM D 2872 : 2004 | Standard Test Method for Effect of Heat and Air on a Moving Film of Asphalt (Rolling Thin-Film Oven Test) |
| ASTM D 5546 : 2009 | Standard Test Method for Solubility of Asphalt Binders in Toluene by Centrifuge (Withdrawn 2017) |
| ASTM D 8 : 2020 : REV A | Standard Terminology Relating to Materials for Roads and Pavements |
| ASTM D 6648 : 2001 | Standard Test Method for Determining the Flexural Creep Stiffness of Asphalt Binder Using the Bending Beam Rheometer (BBR) |
| ASTM D 6373 : 2007 | Standard Specification for Performance Graded Asphalt Binder |
| ASTM D 6521 : 2019 | Standard Practice for Accelerated Aging of Asphalt Binder Using a Pressurized Aging Vessel (PAV) |
| ASTM D 6723 : 2002 | Standard Test Method for Determining the Fracture Properties of Asphalt Binder in Direct Tension (DT) (Withdrawn 2011) |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.