DD CEN ISO/TS 24817:2011

Superseded

Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Add to Watchlist

View superseded by

This Standard has been added successfully to your Watchlist
Please visit My Watchlist to see all standards that you are watching.

Please log in or create an account to add this standard to your Watchlist.

We could not add this standard to your Watchlist.
Please retry or contact support for assistance.

You have already added this standard to your Watchlist.
Visit My Watchlist to view the full list.

Petroleum, petrochemical and natural gas industries. Composite repairs for pipework. Qualification and design, installation, testing and inspection

Available format(s): Hardcopy, PDF

Superseded date: 31-08-2015

Language(s): English

Published date: 30-06-2011

Publisher: British Standards Institution

Add to Watchlist

Table of Contents - (Show below) - (Hide below)

Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definition
4 Symbols and abbreviated terms
5 Applications
6 Qualification and design
7 Installation
8 Testing and inspection
9 System testing
10 Future modifications
11 Decommissioning
Annex A (normative) - Design data sheet
Annex B (normative) - Qualification data
Annex C (normative) - Short-term pipe spool survival test
Annex D (normative) - Measurement of [gamma]LCL for
through-wall defect calculation
Annex E (normative) - Measurement of performance test data
Annex F (normative) - Measurement of impact performance
Annex G (normative) - Measurement of the degradation factor
Annex H (informative) - Axial extent of repair look-up table
Annex I (normative) - Installer qualification
Annex J (normative) - Installation requirements and guidance
Bibliography

Abstract - (Show below) - (Hide below)

Provides requirements and recommendations for the qualification and design, installation, testing and inspection for the external application of composite repairs to corroded or damaged pipework used in the petroleum, petrochemical and natural gas industries.

Scope - (Show below) - (Hide below)

This Technical Specification gives requirements and recommendations for the qualification and design, installation, testing and inspection for the external application of composite repairs to corroded or damaged pipework used in the petroleum, petrochemical and natural gas industries.

General Product Information - (Show below) - (Hide below)

Committee	PSE/17
Development Note	Renumbers and supersedes DD ISO/TS 24817. 2011 Edition incorporates corrigendum to DD ISO/TS 24817. (06/2011)
Document Type	Standard
ISBN
Pages
Published
Publisher	British Standards Institution
Status	Superseded
Superseded By	BS EN ISO 24817:2015 BS EN ISO 24817:2017
Supersedes	DD ISO/TS 24817 : 2006

International Equivalents – Equivalent Standard(s) & Relationship - (Show below) - (Hide below)

Equivalent Standard(s)	Relationship
ISO/TS 24817:2006	Identical
CEN ISO/TS 24817:2011	Identical

Standards Referencing This Book - (Show below) - (Hide below)

ISO 15649:2001	Petroleum and natural gas industries Piping
ISO 527-4:1997	Plastics Determination of tensile properties Part 4: Test conditions for isotropic and orthotropic fibre-reinforced plastic composites
ASME B31.1 : 2016	POWER PIPING
ASME PV CODE 3 ND DIV 1 : 2017	BOILER AND PRESSURE VESSEL CODE - RULES FOR THE CONSTRUCTION OF NUCLEAR FACILITY COMPONENTS - CLASS 3 COMPONENTS
ASTM G 8 : 1996	Standard Test Methods for Cathodic Disbonding of Pipeline Coatings
EN 59:2016	Glass reinforced plastics - Determination of indentation hardness by means of a Barcol hardness tester
ANSI/AWWA C200 : 2017	STEEL WATER PIPE, 6 IN. (150 MM) AND LARGER
ASTM D 543 : 2014 : REDLINE	Standard Practices for Evaluating the Resistance of Plastics to Chemical Reagents
ASME B31.8 : 2016	Gas Transmission and Distribution Piping Systems
ISO 15310:1999	Fibre-reinforced plastic composites Determination of the in-plane shear modulus by the plate twist method
ASME PCC 2 : 2015	REPAIR OF PRESSURE EQUIPMENT AND PIPING
AWWA C151/A21.51 : 2017	DUCTILE-IRON PIPE, CENTRIFUGALLY CAST
ASME B31.3:2016	PROCESS PIPING
ASME B31.4 : 2016	PIPELINE TRANSPORTATION SYSTEMS FOR LIQUIDS AND SLURRIES
ISO 11359-2:1999	Plastics Thermomechanical analysis (TMA) Part 2: Determination of coefficient of linear thermal expansion and glass transition temperature
AWWA C150/A21.50 : 2014	THICKNESS DESIGN OF DUCTILE-IRON PIPE
ASTM D 5379/D5379M : 2012 : REDLINE	Standard Test Method for Shear Properties of Composite Materials by the V-Notched Beam Method
AWWA M11 : 2004	STEEL PIPE: A GUIDE FOR DESIGN AND INSTALLATION
ISO 11357-2:2013	Plastics Differential scanning calorimetry (DSC) Part 2: Determination of glass transition temperature and glass transition step height
ASTM C 581 : 2015 : REDLINE	Standard Practice for Determining Chemical Resistance of Thermosetting Resins Used in Glass-Fiber-Reinforced Structures Intended for Liquid Service
ASTM D 696 : 2016 : REDLINE	Standard Test Method for Coefficient of Linear Thermal Expansion of Plastics Between −30°C and 30°C with a Vitreous Silica Dilatometer
ASTM D 790 : 2017 : REDLINE	Standard Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials
ISO 10952:2014	Plastics piping systems Glass-reinforced thermosetting plastics (GRP) pipes and fittings Determination of the resistance to chemical attack for the inside of a section in a deflected condition
ISO 75-3:2004	Plastics — Determination of temperature of deflection under load — Part 3: High-strength thermosetting laminates and long-fibre-reinforced plastics
ASTM D 2992 : 2012	Standard Practice for Obtaining Hydrostatic or Pressure Design Basis for “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe and Fittings
ASTM D 638 : 2014 : REDLINE	Standard Test Method for Tensile Properties of Plastics
EN 1465:2009	Adhesives - Determination of tensile lap-shear strength of bonded assemblies
ISO 527-1:2012	Plastics Determination of tensile properties Part 1: General principles
ISO 13623:2017	Petroleum and natural gas industries — Pipeline transportation systems
ISO 868:2003	Plastics and ebonite Determination of indentation hardness by means of a durometer (Shore hardness)
ISO 14129:1997	Fibre-reinforced plastic composites — Determination of the in-plane shear stress/shear strain response, including the in-plane shear modulus and strength, by the plus or minus 45 degree tension test method

Categories associated with this Standard - (Show below) - (Hide below)

Sub-Categories associated with this Standard - (Show below) - (Hide below)

Add To Cart

Product Format

Quantity

Buy now

Add to cart

Create account