DEFSTAN 02-38/1(2005) : 2005
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
REQUIREMENTS FOR THE PREPARATION, IDENTIFICATION AND MANAGEMENT OF DATUM PACK DRAWINGS AND PHOTOGRAPHS FOR S AND T NUCLEAR SUBMARINES
Hardcopy , PDF
14-01-2011
English
01-01-2005
1 Scope
2 Warning
3 Normative References
4 Definitions
5 Abbreviations
6 Completeness of Drawings
7 General Drawing Standards & Requirements
7.1 Categorisation of DP Drawings
7.2 Drawing Standards
7.3 Drawing and Document Lists
7.4 Drawing Presentation
7.5 Supply of Master Drawings
7.6 Magnetic Material
7.7 Drawing Requirements
8 Specific Drawing Definitions
8.1 Submarine Structural Drawings
8.2 Submiss/Subsunk Drawings
8.3 First Level Definition
8.4 Docking Plans
8.5 Computerised Drawings from Engineering Models (CODEM)
8.6 Reduced Size Drawings
8.7 Cabling & Pipework
8.8 Electrical Drawings
8.9 Panel Electronic Circuit (PEC) Drawings
8.10 Service Packaging Instruction Sheets (SPIS)
8.11 Service Interface Diagrams (SID)
8.12 Reactor Control & Instrumentation (RC&I) Drawings
8.13 Completion of Prepared Spaces
9 Limiting Requirements
10 Microfilming and Aperature Cards
10.1 Microfilm
10.2 Punch Code
11 Models and Mock-Ups
12 Photographs and Videos
13 Identification Requirements
13.1 Introduction
13.2 Responsible Authority Codes
13.3 Numbering of Drawings
13.4 BAe Systems (Ex VSEL) Drawing Numbers
13.5 Weapon Equipments
13.6 Data Strip - Additional Data
13.7 Drawing Cross-Reference in Other Documents
13.8 Security & Caveat Markings
14 Swiftsure Class - Updating Datum Pack Drawings
14.1 General
14.2 Drawing Sheets & Formats
14.3 Recording Changes On Change Record Sheets
(Preferred Method)
14.4 Recording Changes On Change Record Sheets
(Alternative Method)
14.5 Drawing Issue Updating Requirements
14.6 Drawing Issue Updating Procedures
14.7 Conversion Of Class Drawings to Submarine Specific
14.8 Amendment to Drawing Numbers and Issue States
14.9 System Component & Detail Drawing Amendment
14.10 Equipment Drawings
14.11 Equipment Component & Detail Drawing Amendment
14.12 Responsibility for Updating the Master Drawing
14.13 Additional & New Drawings
14.14 Metric & Imperial Measurements
14.15 Submiss/Subsunk Drawings
14.16 Reduced Size Drawings
14.17 Standard Drawings - Hull & Mechanical
14.18 Docking Plan
14.19 Reactor Control & Instrumentation (RC&I) Drawings
15 Swiftsure Class - Requirements for The Management
Control & Distribution of Datum Pack Drawings & Microfilms
15.1 General Requirements
15.2 Filing & Storing
15.3 Copying & Distribution
15.4 Drawing/Microfilm - Control & Issue
15.5 Comprehensive Drawing Indices
15.6 Drawing Supply - Timescales
15.7 Submiss/Subsunk, Escape, Rescue & Salvage Information
Drawings
15.8 First Level Area Diagrams & First Level Fittings List
15.9 All Other Drawings
15.10 Disposal of Drawings
16 Trafalgar Class - Updating Datum Pack Drawings
16.1 General
16.2 Drawing Sheets & Formats
16.3 Recording Changes on Change Record Sheets
(Preferred Method)
16.4 Recording Changes on Change Record Sheets
(Alternative Method)
16.5 Drawing Issue Updating Requirements
16.6 Drawing Issue Updating Procedures
16.7 Conversion Of Class Drawings to Submarine Specific
16.8 Amendment To Drawing Numbers and Issue States
16.9 System Arrangement & Detail Drawing Amendment
16.10 Equipment Drawings
16.11 Equipment Component & Detail Drawing Amendment
16.12 Responsibility for Updating the Master Drawing
16.13 Additional & New Drawings
16.14 Metric & Imperial Measurements
16.15 Submiss/Subsunk Drawings
16.16 Reduced Size Drawings
16.17 Standard Drawings - Hull & Mechanical
16.18 Docking Plan
16.19 ISOPAC Drawings
16.20 Reactor Control & Instrumentation (RC&I) Drawings
17 Trafalgar Class - Requirements for The Management
Control & Distribution of Datum Pack Drawings & Microfilms
17.1 General Requirements
17.2 Filing & Storing
17.3 Copying & Distribution
17.4 Drawing/Microfilm - Control & Issue
17.5 Comprehensive Drawing Indices
17.6 Drawing Supply - Timescales
17.7 Submiss/Subsunk, Escape, Rescue & Salvage
Information Drawings
17.8 First Level Area Diagrams & First Level Fittings List
17.9 All Other Drawings
17.10 Disposal Of Drawings
Important note : All end users must be registered with an Account prior to user licenses being assigned.Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.