Generic Specification: Solid state all-or-nothing relays of assessed quality - Generic data and methods of test

Published date

15-10-1991

Publisher

European Committee for Standards - Electrical

Foreword
Preface
SECTION 1 SCOPE
SECTION 2 GENERAL
            2.1 Order of precedence
            2.2 Related documents
            2.3 Units, symbols and terminology
            2.4 Preferred values
            2.5 Marking
SECTION 3 TERMS AND DEFINITIONS
            3.1 Construction
            3.2 Type of relays
            3.3 General terms
            3.4 Prefixes for the values applicable to
                  relays
            3.5 Control signal values
            3.6 Output values
            3.7 Terms relating to times
SECTION 4 QUALITY ASSESSMENT PROCEDURES
            4.1 Primary stage of manufacture
            4.2 Structurally similar components
            4.3 Qualification approval procedures
            4.4 Quality conformance inspection
            4.5 Division into groups
            4.6 Resubmission of rejected lots
            4.7 Certified test records
            4.8 Delivery of relays subjected to tests
            4.9 Delayed delivery
            4.10 Supplementary procedures for deliveries
            4.11 Unchecked parameters
            4.12 Release for delivery before the completion
                  of Group B tests
SECTION 5 TEST AND MEASUREMENT PROCEDURE
            5.1 General
            5.2 Alternative methods
            5.3 Precision of measurement
            5.4 Requirements in detail specifications
            5.5 Standard conditions for testing
            5.6 Visual inspection and check of dimensions
            5.7 Mass
            5.8 Terminal identification
            5.9 "Must operate" and :"Must release" control
                  signal current and voltage ION, VON, VO
            5.10 Peak on-state voltage VTM
            5.11 Zero turn-on voltage VTO
            5.12 Surge (Non-repetitive) on-state current ITSM
            5.13 Surge (Non-repetitive) on-state current ITSM
                  (with rapid rate of rise of reverse voltage)
            5.14 Critical rate of rise of on-state current
                  dI/dt
            5.15 Critical rate of rise of commutating
                  voltage dV/dt
            5.16 Critical rate of rise of off-state voltage
                  dV/dt
            5.17 Off-state current ID
            5.18 Repetitive peak off-state voltage VDRM
            5.19 Non-repetitive peak off-state voltage VDSM
            5.20 Input circuit resistance
            5.21 Dielectric test
            5.22 Insulation resistance
            5.23 Climatic sequence
            5.24 Damp heat steady state
            5.25 Rapid change of temperature
            5.26 Accelerated thermal cycling
            5.27 Enclosure
            5.28 Corrosive atmosphere
            5.29 Mould growth
            5.30 Robustness of terminals
            5.31 Soldering
            5.32 Shock
            5.33 Bump
            5.34 Vibration
            5.35 Acceleration
            5.36 Electrical endurance
            5.37 Thermal endurance
            5.38 Voltage blocking
            5.39 Resistance to solvents
            5.40 Fire hazard
            5.41 Radio frequency interference
                  (under consideration)

Gives test and measuring methods for selection to be used in detail specifications for solid state relays of assessed quality. In addition, it defines the quality assurance procedures.

Committee	CLC/SR 94
DocumentType	Standard
PublisherName	European Committee for Standards - Electrical
Status	Current

Standards	Relationship
DIN EN 117000:1992-02	Identical
CECC 17000 : 1990	Identical
PN EN 117000 : DEC 2002	Identical
UNE-EN 117000:1991	Identical
BS EN 117000:1997	Identical
I.S. EN 117000:1994	Identical

IEC 60068-1:2013	Environmental testing - Part 1: General and guidance
IEC 60695-2-1:1991	Fire hazard testing - Part 2: Test methods - Section 1: Glow-wire test and guidance
IEC 60068-2-27:2008	Environmental testing - Part 2-27: Tests - Test Ea and guidance: Shock
IEC 60068-2-20:2008	Environmental testing - Part 2-20: Tests - Test T: Test methods for solderability and resistance to soldering heat of devices with leads
IEC 60068-2-21:2006	Environmental testing - Part 2-21: Tests - Test U: Robustness of terminations and integral mounting devices
IEC 60068-2-13:1983	Basic environmental testing procedures - Part 2-13: Tests - Test M: Low air pressure
IEC 60068-2-11:1981	Basic environmental testing procedures - Part 2-11: Tests - Test Ka: Salt mist
IEC 60410:1973	Sampling plans and procedures for inspection by attributes
IEC 60068-2-3:1969	Basic environmental testing procedures - Part 2-3: Tests - Test Ca: Damp heat, steady state
ISO 8601:2004	Data elements and interchange formats Information interchange Representation of dates and times
IEC 60068-2-17:1994	Basic environmental testing procedures - Part 2-17: Tests - Test Q: Sealing
IEC 60068-2-10:2005	Environmental testing - Part 2-10: Tests - Test J and guidance: Mould growth
IEC 60068-2-2:2007	Environmental testing - Part 2-2: Tests - Test B: Dry heat
IEC 60255-5:2000	Electrical Relays - Part 5: Insulation coordination for measuring relays and protection equipment - Requirements and tests
IEC 60255-1:1967	Electrical relays - Part 1: Instantaneous all-or-nothing relays
IEC 60068-2-29:1987	Environmental testing. Part 2: Tests. Test Eb and guidance: Bump
IEC 60443:1974	Stabilized supply apparatus for measurement
IEC 60068-2-1:2007	Environmental testing - Part 2-1: Tests - Test A: Cold
IEC 60144:1963	Degrees of protection of enclosures for low-voltage switchgear and controlgear
IEC 60068-2-14:2009	Environmental testing - Part 2-14: Tests - Test N: Change of temperature
CECC 00007 : 1978	BASIC SPECIFICATION: SAMPLING PLANS AND PROCEDURES FOR INSPECTION BY ATTRIBUTES
IEC 60068-2-30:2005	Environmental testing - Part 2-30: Tests - Test Db: Damp heat, cyclic (12 h + 12 h cycle)