EN 14628:2005
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Ductile iron pipes, fittings and accessories - External polyethylene coating for pipes - Requirements and test methods
12-03-2022
12-10-2005
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Ordering information
5 Technical Requirements
6 Performance requirements
7 Test Methods
Annex A (informative) Quality assurance
Annex B (informative) Application process
Annex C (informative) Coating material
Bibliography
This European Standard defines the requirements and test methods applicable to factory applied extruded polyethylene coatings for the external corrosion protection of ductile iron pipes conforming to EN 545, EN 598 and EN 969 for use at operating temperatures up to 50 °C.This European Standard does not cover ductile iron pipes protected with thin PE sleeve. Special works at site like drilling, tapping etc. may influence the corrosion protection properties. Those job steps shall be included in the instructions of pipe saddle and accessory manufacturers and all other essential installation instructions. These instructions are not part of this European Standard.
| Committee |
CEN/TC 203
|
| DocumentType |
Standard
|
| PublisherName |
Comite Europeen de Normalisation
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| NS EN 14628 : 1ED 2005 | Identical |
| SN EN 14628 : 2005 | Identical |
| DIN EN 14628 E : 2006 | Identical |
| PN EN 14628 : 2006 | Identical |
| UNE-EN 14628:2006 | Identical |
| NEN EN 14628 : 2005 | Identical |
| NF EN 14628 : 2006 | Identical |
| I.S. EN 14628:2005 | Identical |
| UNI EN 14628 : 2006 | Identical |
| BS EN 14628:2005 | Identical |
| NBN EN 14628 : 2006 | Identical |
| DIN EN 14628:2006-01 | Identical |
| BS ISO 13470:2012 | Trenchless applications of ductile iron pipes systems. Product design and installation |
| EN 545:2010 | Ductile iron pipes, fittings, accessories and their joints for water pipelines - Requirements and test methods |
| ISO 13470:2012 | Trenchless applications of ductile iron pipes systems — Product design and installation |
| DIN EN 598:2009-10 | Ductile iron pipes, fittings, accessories and their joints for sewerage applications - Requirements and test methods (includes Amendment A1:2009) |
| BS EN 598 : 2007 | DUCTILE IRON PIPES, FITTINGS, ACCESSORIES AND THEIR JOINTS FOR SEWERAGE APPLICATIONS - REQUIREMENTS AND TEST METHODS |
| UNE-EN 545:2011 | Ductile iron pipes, fittings, accessories and their joints for water pipelines - Requirements and test methods |
| I.S. EN 598:2007 | DUCTILE IRON PIPES, FITTINGS, ACCESSORIES AND THEIR JOINTS FOR SEWERAGE APPLICATIONS - REQUIREMENTS AND TEST METHODS |
| I.S. EN 545:2010 | DUCTILE IRON PIPES, FITTINGS, ACCESSORIES AND THEIR JOINTS FOR WATER PIPELINES - REQUIREMENTS AND TEST METHODS |
| BS EN 545:2010 | Ductile iron pipes, fittings, accessories and their joints for water pipelines. Requirements and test methods |
| UNI EN 545 : 2010 | DUCTILE IRON PIPES, FITTINGS, ACCESSORIES AND THEIR JOINTS FOR WATER PIPELINES - REQUIREMENTS AND TEST METHODS |
| UNI EN 598 : 2009 | DUCTILE IRON PIPES, FITTINGS, ACCESSORIES AND THEIR JOINTS FOR SEWERAGE APPLICATIONS - REQUIREMENTS AND TEST METHODS |
| EN 598:2007+A1:2009 | Ductile iron pipes, fittings, accessories and their joints for sewerage applications - Requirements and test methods |
| DIN EN 545:2011-09 | Ductile iron pipes, fittings, accessories and their joints for water pipelines - Requirements and test methods |
| ISO/IEC Guide 62:1996 | General requirements for bodies operating assessment and certification/registration of quality systems |
| ISO 3219:1993 | Plastics — Polymers/resins in the liquid state or as emulsions or dispersions — Determination of viscosity using a rotational viscometer with defined shear rate |
| EN 598:2007+A1:2009 | Ductile iron pipes, fittings, accessories and their joints for sewerage applications - Requirements and test methods |
| EN ISO 527-2:2012 | Plastics - Determination of tensile properties - Part 2: Test conditions for moulding and extrusion plastics (ISO 527-2:2012) |
| ISO 3681:1996 | Binders for paints and varnishes — Determination of saponification value — Titrimetric method |
| EN ISO 527-1:2012 | Plastics - Determination of tensile properties - Part 1: General principles (ISO 527-1:2012) |
| EN 969:2009 | Ductile iron pipes, fittings, accessories and their joints for gas pipelines - Requirements and test methods |
| ISO 6708:1995 | Pipework components Definition and selection of DN (nominal size) |
| ISO 527-2:2012 | Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and extrusion plastics |
| EN ISO 6708:1995 | Pipework components - Definition and selection of DN (nominal size) (ISO 6708:1995) |
| EN ISO 9001:2015 | Quality management systems - Requirements (ISO 9001:2015) |
| EN 1238:2011 | Adhesives - Determination of the softening point of thermoplastic adhesives (ring and ball) |
| EN ISO 3219:1994 | Plastics - Polymers/resins in the liquid state or as emulsions or dispersions - Determination of viscosity using a rotational viscometer with defined shear rate (ISO 3219:1993) |
| ISO 9001:2015 | Quality management systems — Requirements |
| ISO 4892-2:2013 | Plastics — Methods of exposure to laboratory light sources — Part 2: Xenon-arc lamps |
| EN ISO 3681:1998 | Binders for paints and varnishes - Determination of saponification value - Titrimetric method (ISO 3681:1996) |
| EN ISO 1133:2005 | PLASTICS - DETERMINATION OF THE MELT MASS-FLOW RATE (MFR) AND THE MELT VOLUME-FLOW RATE (MVR) OF THE THERMOPLASTICS |
| EN 545:2010 | Ductile iron pipes, fittings, accessories and their joints for water pipelines - Requirements and test methods |
| EN 45012 : 1998 | GENERAL REQUIREMENTS FOR BODIES OPERATING ASSESSMENT AND CERTIFICATION/REGISTRATION OF QUALITY SYSTEMS |
| EN ISO 4892-2:2013 | Plastics - Methods of exposure to laboratory light sources - Part 2: Xenon-arc lamps (ISO 4892-2:2013) |
| ISO 1133:2005 | Plastics Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics |
| ISO 527-1:2012 | Plastics Determination of tensile properties Part 1: General principles |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.