I.S. EN 15167-2:2007

Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Tasks for the manufacturer
  4.1 Factory production control
      4.1.1 Concept
      4.1.2 Works' quality manual
      4.1.3 Management systems
      4.1.4 System of documentation
  4.2 Internal quality control
      4.2.1 Process control
      4.2.2 Measuring and testing
      4.2.3 Handling, storage, packaging and delivery
  4.3 Autocontrol testing of samples
      4.3.1 Sampling and testing
      4.3.2 Corrective action
      4.3.3 Measuring and test equipment for autocontrol
            testing
      4.3.4 Quality records
5 Tasks for the certification body
  5.1 General
  5.2 Surveillance, assessment and acceptance of the
      production control
      5.2.1 Inspection tasks
      5.2.2 Frequency of inspections
      5.2.3 Reports
  5.3 Evaluation of the results of autocontrol testing
      of samples
      5.3.1 Evaluation tasks
      5.3.2 Number and timing of evaluations
      5.3.3 Control period
      5.3.4 Evaluation of test results
      5.3.5 Reports
  5.4 Audit testing of samples taken at the factory/depot
      and initial type testing
      5.4.1 Sampling
      5.4.2 Number of samples
      5.4.3 Properties and test methods
      5.4.4 Testing
      5.4.5 Evaluation of test results
      5.4.6 Reports
      5.4.7 Proficiency testing
  5.5 Initial inspection of the factory and the production
      control
      5.5.1 Inspection of a new factory
      5.5.2 Inspection of an existing factory
      5.5.3 Criteria for the assessment of the production
            equipment
      5.5.4 Criteria for the assessment of laboratories
      5.5.5 Reports
  5.6 Evaluation of test results during the initial period
      5.6.1 Initial period
      5.6.2 Evaluation of test results
      5.6.3 Reports
6 Actions in the event of non-conformity
  6.1 Actions to be taken by the manufacturer
  6.2 Actions to be taken by the certification body
      6.2.1 Following surveillance, assessment and acceptance
            of the production control and evaluation of the
            results of autocontrol testing
      6.2.2 Following evaluation of the results of the audit
            testing of samples taken at the factory/depot
7 Procedure for third party certification of conformity
8 Certificates of conformity and conformity mark
9 Requirements for dispatching centres
  9.1 General requirements
  9.2 Tasks for the intermediary
      9.2.1 Measures to maintain the ground granulated
            blastfurnace slag quality
      9.2.2 Confirmation autocontrol testing of samples
            taken at the dispatching centre
  9.3 Tasks for the third party
      9.3.1 Surveillance, assessment and acceptance of the
            measures to maintain the ground granulated
            blastfurnace slag quality and of the confirmation
            autocontrol
      9.3.2 Audit testing of samples taken at the dispatching
            centre
      9.3.3 Decisions to be taken
Annex A (normative) - Evaluation of the representativeness and
                      the accuracy of the 28 day activity index
                      test results
        A.1 General
        A.2 Sets of results considered
        A.3 Evaluation procedure
            A.3.1 Introduction
            A.3.2 Symbols
            A.3.3 Evaluation of whether set A and set B belong
                  to the same population (sampling error check)
            A.3.4 Comparison between set B and set C in order to
                  check the accuracy of the autocontrol testing
                  (testing error check)
Bibliography