We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
  • I.S. EN 60706-2:2006

    Current The latest, up-to-date edition.
    Add to Watchlist
    This Standard has been added successfully to your Watchlist
    Please visit My Watchlist to see all standards that you are watching.
    Please log in or to add this standard to your Watchlist.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    You have already added this standard to your Watchlist.
    Visit My Watchlist to view the full list.

    MAINTAINABILITY OF EQUIPMENT - PART 2: MAINTAINABILITY REQUIREMENTS AND STUDIES DURING THE DESIGN AND DEVELOPMENT PHASE

    Available format(s):  Hardcopy, PDF

    Language(s):  English

    Published date:  01-01-2006

    Publisher:  National Standards Authority of Ireland

    Add to Watchlist

    For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
    Only cited Standards give presumption of conformance to New Approach Directives/Regulations.

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    FOREWORD
    INTRODUCTION
    1 Scope
    2 Normative references
    3 Terms, definitions and acronyms
      3.1 Terms and definitions
      3.2 Acronyms
    4 General approach
    5 Principle of maintainability
    6 Maintainability activities in the life cycle
      6.1 General
      6.2 Concept and definition phase
      6.3 Design and development phase
      6.4 Manufacture and installation phase
      6.5 Operation and maintenance phases
      6.6 Disposal phase
    7 Specification of maintainability requirements
      7.1 Statement of maintainability requirements
      7.2 Maintainability characteristics
      7.3 Constraints
      7.4 Maintainability programme requirements
      7.5 Verification
    8 Maintainability studies in the design and development phase
      8.1 General
      8.2 Objectives
      8.3 Maintainability studies in the design process
      8.4 Analysis tools and procedures
    9 Design support
      9.1 Liaison
      9.2 Design criteria and check-lists
      9.3 Design reviews
    Annex A (informative) Maintainability allocation
    Annex B (informative) Example of a maintainability allocation
    Annex C (informative) Example of allocation of reliability
            values and maintenance strategy selection for a system
            with non-constant failure rate
    Annex ZA (normative) Normative references to international
             publications with their corresponding European
             publications
    Bibliography

    Abstract - (Show below) - (Hide below)

    Covers the maintainability requirements and related design and use parameter, and discusses some activities necessary to achieve the required maintainability characteristics and their relationship to planning of maintenance. It describes the general approach in reaching these objectives and shows how maintainability characteristics should be specified in a requirements document or contract.

    General Product Information - (Show below) - (Hide below)

    Development Note For CENELEC adoptions of IEC publications, please check www.iec.ch to be sure that you have any corrigenda that may apply. (01/2017)
    Document Type Standard
    Publisher National Standards Authority of Ireland
    Status Current

    Standards Referencing This Book - (Show below) - (Hide below)

    IEC 61025:2006 Fault tree analysis (FTA)
    EN 60812 : 2006 ANALYSIS TECHNIQUES FOR SYSTEM RELIABILITY - PROCEDURE FOR FAILURE MODE AND EFFECTS ANALYSIS (FMEA)
    IEC 60812:2006 Analysis techniques for system reliability - Procedure for failure mode and effects analysis (FMEA)
    IEC 60300-3-3:2017 Dependability management - Part 3-3: Application guide - Life cycle costing
    IEC 61649:2008 Weibull analysis
    IEC 60300-3-12:2011 Dependability management - Part 3-12: Application guide - Integrated logistic support
    IEC 60300-3-14:2004 Dependability management - Part 3-14: Application guide - Maintenance and maintenance support
    IEC 60706-3:2006 Maintainability of equipment - Part 3: Verification and collection, analysis and presentation of data
    IEC 61160:2005 Design review
    EN 60300-3-1 : 2004 DEPENDABILITY MANAGEMENT - PART 3-1: APPLICATION GUIDE - ANALYSIS TECHNIQUES FOR DEPENDABILITY - GUIDE ON METHODOLOGY
    EN 60300-3-12:2011 DEPENDABILITY MANAGEMENT - PART 3-12: APPLICATION GUIDE - INTEGRATED LOGISTIC SUPPORT
    EN 60300-3-14 : 2004 DEPENDABILITY MANAGEMENT - PART 3-14: APPLICATION GUIDE - MAINTENANCE AND MAINTENANCE SUPPORT
    EN 60300-3-3:2017 Dependability management - Part 3-3: Application guide - Life cycle costing
    IEC 60300-3-1:2003 Dependability management - Part 3-1: Application guide - Analysis techniques for dependability - Guide on methodology
    IEC 60300-1:2014 Dependability management - Part 1: Guidance for management and application
    HD 617 : 200S1 FAULT TREE ANALYSIS (FTA)
    IEC 60300-3-11:2009 Dependability management - Part 3-11: Application guide - Reliability centred maintenance
    IEC 60300-2:2004 Dependability management - Part 2: Guidelines for dependability management
    IEC 60300-3-10:2001 Dependability management - Part 3-10: Application guide - Maintainability
    IEC 60706-5:2007 Maintainability of equipment - Part 5: Testability and diagnostic testing
    EN 61160 : 2005 DESIGN REVIEW
    IEC 61710:2013 Power law model - Goodness-of-fit tests and estimation methods
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective