We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
  • ASTM C 547 : 2017 : REDLINE

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    Add to Watchlist
    This Standard has been added successfully to your Watchlist.
    Please visit My Watchlist to see all standards that you are watching.
    Please log in or to add this standard to your Watchlist.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    You need to be logged in to add this standard to your Watchlist.
    Please log in now or create an account to add.
    You already added this Product in the Watchlist.

    Standard Specification for Mineral Fiber Pipe Insulation

    Available format(s):  PDF

    Superseded date:  23-04-2020

    Language(s):  English

    Published date:  01-09-2017

    Publisher:  American Society for Testing and Materials

    Add to Watchlist

    Add To Cart

    Abstract - (Show below) - (Hide below)

    CONTAINED IN VOL. 04.06, 2017 Defines mineral fiber insulation produced to form hollow cylinders for standard pipe and tubing sizes.

    Scope - (Show below) - (Hide below)

    1.1This specification covers mineral fiber insulation produced to form hollow cylinders for standard pipe and tubing sizes. Use mineral fiber pipe insulation that has been either molded or precision v-grooved, with one or more walls split longitudinally for use on pipe temperatures up to 1400°F (760°C).

    1.2For satisfactory performance, use properly installed protective vapor retarders or barriers on sub-ambient temperature applications to reduce movement of moisture through or around the insulation to the colder surface. Failure to use a vapor barrier can lead to insulation and system damage. Refer to Practice C921 to aid material selection.

    1.3Flexible mineral fiber wrap products such as perpendicular-oriented fiber insulation rolls, non-precision or manually scored block or board, or flexible boards or blankets used as pipe insulation, are not covered by this specification.

    1.4The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

    1.5For Naval Sea Systems Command (NAVSEA) acceptance, materials must also comply with Supplemental Requirements. See Annex A1 of this standard.

    1.6The following safety hazards caveat applies to the test methods portion, Section 11, only: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

    1.7This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

    General Product Information - (Show below) - (Hide below)

    Committee C 16
    Development Note Supersedes ASTM C 281 and ASTM C 300 (01/2002) Supersedes HH I 558. (04/2004)
    Document Type Redline
    Publisher American Society for Testing and Materials
    Status Superseded
    Superseded By
    Supersedes

    Standards Referenced By This Book - (Show below) - (Hide below)

    ASTM C 1094 : 2001 Standard Guide for Flexible Removable Insulation Covers
    ASTM C 1094 : 2001 : R2006 Standard Guide for Flexible Removable Insulation Covers (Withdrawn 2010)
    ASTM F 683 : 2014 : REDLINE Standard Practice for Selection and Application of Thermal Insulation for Piping and Machinery
    ICC 2012 INTERNATIONAL BUILDING CODE : 2012 INTERNATIONAL BUILDING CODE
    ASTM C 1696 : 2016 : REDLINE Standard Guide for Industrial Thermal Insulation Systems
    ICC IBC INTERNATIONAL BUILDING CODE : 2015 INTERNATIONAL BUILDING CODE
    IEEE 515.1-2012 TESTING, DESIGN, INSTALLATION, AND MAINTENANCE OF ELECTRICAL RESISTANCE TRACE HEATING FOR COMMERCIAL APPLICATIONS

    Standards Referencing This Book - (Show below) - (Hide below)

    ASTM C 680 : 2014 : REDLINE Standard Practice for Estimate of the Heat Gain or Loss and the Surface Temperatures of Insulated Flat, Cylindrical, and Spherical Systems by Use of Computer Programs
    ULC S102 : 7ED 2010 STANDARD METHOD OF TEST FOR SURFACE BURNING CHARACTERISTICS OF BUILDING MATERIALS AND ASSEMBLIES
    UL 723 : 2010 TEST FOR SURFACE BURNING CHARACTERISTICS OF BUILDING MATERIALS
    ASTM C 356 : 2017 : REDLINE Standard Test Method for Linear Shrinkage of Preformed High-Temperature Thermal Insulation Subjected to Soaking Heat
    ASTM C 447 : 2015 : REDLINE Standard Practice for Estimating the Maximum Use Temperature of Thermal Insulations
    ASTM C 795 : 2008 Standard Specification for Thermal Insulation for Use in Contact with Austenitic Stainless Steel
    ASTM C 335/C335M : 2017 : REDLINE Standard Test Method for Steady-State Heat Transfer Properties of Pipe Insulation
    ASTM C 168 : 2017-06 TERMINOLOGY RELATING TO THERMAL INSULATION
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective