Customer Support: +44 (0)203 327 3140

Login to i2i Subscription Intertek.com
  • There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Go to AMERICAS site
Dismiss alert
Please enter a keyword to search
Advanced search
Home
ASTM
ASTM D 6184 : 2017 : REDLINE

ASTM D 6184 : 2017 : REDLINE

Superseded

Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Test Method for Oil Separation from Lubricating Grease (Conical Sieve Method)

Available format(s)

PDF

Superseded date

27-12-2022

Language(s)

English

Published date

21-06-2017

Publisher

American Society for Testing and Materials

CONTAINED IN VOL. 05.03, 2017 Defines the determination of the tendency of lubricating grease to separate oil at an elevated temperature.

1.1This test method covers the determination of the tendency of lubricating grease to separate oil at an elevated temperature. This test method shall be conducted at 100 °C for 30 h unless other conditions are required by the grease specification.

1.2This test method can be used on any grease with a worked penetration (Test Methods D217) greater than 220 mm/10 (NLGI Consistency Number 3 or softer). However, no precision data exists for greases with a penetration greater than 340 mm/10 (softer than NLGI Consistency Number 1).

1.3The values stated in SI units are to be regarded as standard. The term 60 mesh is used to describe the wire mesh used. This unit was described in the withdrawn E437 standard and there is no exact metric equivalent.

1.4This standard does not purport to address all the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety practices and determine the applicability of regulatory limitations prior to use.

1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Committee
D 02
DocumentType
Redline
Pages
4
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy

SAE AMS 3052 : 2013 GREASE, AIRCRAFT, GENERAL PURPOSE, LOW TEMPERATURE RANGE, LITHIUM THICKENED
MIL-PRF-32014 Revision A:2006 GREASE, AIRCRAFT AND INSTRUMENT
MIL-DTL-21567 Revision B:2009 COMPOUND, SILICONE, SOFT FILM
ISO 13678:2010 Petroleum and natural gas industries Evaluation and testing of thread compounds for use with casing, tubing, line pipe and drill stem elements
MIL-PRF-27617 Revision G:2011 GREASE, AIRCRAFT AND INSTRUMENT, FUEL AND OXIDIZER RESISTANT
MIL-DTL-47113 Revision E:2012 COMPOUND, HEAT SINK, SILICONE AND/OR NON-SILICONE
MIL-PRF-83363 Revision E:2014 GREASE, TRANSMISSION, HELICOPTER (NATO G-396)
API 5A3 REDLINE : 2009 RECOMMENDED PRACTICE ON THREAD COMPOUNDS FOR CASING, TUBING, LINE PIPE, AND DRILL STEM ELEMENTS
ACI 423.7 : 2014 SPECIFICATION FOR UNBONDED SINGLE-STRAND TENDON MATERIALS
UNI EN ISO 13678 : 2012 PETROLEUM AND NATURAL GAS INDUSTRIES - EVALUATION AND TESTING OF THREAD COMPOUNDS FOR USE WITH CASING, TUBING, LINE PIPE AND DRILL STEM ELEMENTS
BS EN ISO 13678:2012 Petroleum and natural gas industries. Evaluation and testing of thread compounds for use with casing, tubing, line pipe and drill stem elements
MIL-PRF-10924 Revision H:2008 GREASE, AUTOMOTIVE AND ARTILLERY
SAE AMS 3058 : 2013 GREASE: WIDE TEMPERATURE RANGE LITHIUM OR LITHIUM COMPLEX THICKENED FOR AIRCRAFT WHEEL BEARINGS
I.S. EN ISO 13678:2012 PETROLEUM AND NATURAL GAS INDUSTRIES - EVALUATION AND TESTING OF THREAD COMPOUNDS FOR USE WITH CASING, TUBING, LINE PIPE AND DRILL STEM ELEMENTS (ISO 13678:2010)
EN ISO 13678:2012 Petroleum and natural gas industries - Evaluation and testing of thread compounds for use with casing, tubing, line pipe and drill stem elements (ISO 13678:2010)
API 5A3 : 2011 RECOMMENDED PRACTICE ON THREAD COMPOUNDS FOR CASING, TUBING, LINE PIPE, AND DRILL STEM ELEMENTS
API 5A3 RUSSIAN : 2015 RECOMMENDED PRACTICE ON THREAD COMPOUNDS FOR CASING, TUBING, LINE PIPE, AND DRILL STEM ELEMENTS
SAE J 2695 : 2005 HEAVY DUTY VEHICLE LUBRICATING GREASES

ASTM D 217 : 2017 : REDLINE TEST METHODS FOR CONE PENETRATION OF LUBRICATING GREASE

View more information
£55.10
Excluding VAT
GBP
CAD
CHF
CNY
DKK
EUR
GBP
HKD
IDR
INR
JPY
KRW
MXN
NOK
NZD
SEK
SGD
USD
ZAR
PDF - English
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Learn more on subscription solutions

or

Get in touch with us