We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
  • ASTM E 1237 : 1993 : R2014

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    Add to Watchlist
    This Standard has been added successfully to your Watchlist.
    Please visit My Watchlist to see all standards that you are watching.
    Please log in or to add this standard to your Watchlist.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    You need to be logged in to add this standard to your Watchlist.
    Please log in now or create an account to add.
    You already added this Product in the Watchlist.

    Standard Guide for Installing Bonded Resistance Strain Gages

    Available format(s):  Hardcopy, PDF

    Superseded date:  10-09-2020

    Language(s):  English

    Published date:  15-04-2014

    Publisher:  American Society for Testing and Materials

    Add to Watchlist

    Add To Cart

    Abstract - (Show below) - (Hide below)

    CONTAINED IN VOL. 03.01, 2015 Gives guidelines for installing bonded resistance strain gages.

    Scope - (Show below) - (Hide below)

    1.1This guide provides guidelines for installing bonded resistance strain gages. It is not intended to be used for bulk or diffused semiconductor gages. This document pertains only to adhesively bonded strain gages.

    1.2The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

    1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

    General Product Information - (Show below) - (Hide below)

    Committee E 28
    Document Type Guide
    Product Note Reconfirmed 2014
    Publisher American Society for Testing and Materials
    Status Superseded
    Superseded By
    Supersedes

    Standards Referenced By This Book - (Show below) - (Hide below)

    ASTM D 5448/D5448M : 2016 Standard Test Method for Inplane Shear Properties of Hoop Wound Polymer Matrix Composite Cylinders
    ASTM E 251 : 1992 : R2014 Standard Test Methods for Performance Characteristics of Metallic Bonded Resistance Strain Gages
    ASTM D 6856/D6856M : 2003 : R2016 Standard Guide for Testing Fabric-Reinforced “Textile” Composite Materials
    ASTM E 1426 : 2014 Standard Test Method for Determining the X-Ray Elastic Constants for Use in the Measurement of Residual Stress Using X-Ray Diffraction Techniques
    ASTM D 5687/D5687M : 1995 : R2015 Standard Guide for Preparation of Flat Composite Panels with Processing Guidelines for Specimen Preparation
    ASTM D 3410/D3410M : 2016 Standard Test Method for Compressive Properties of Polymer Matrix Composite Materials with Unsupported Gage Section by Shear Loading
    ASTM D 5449/D5449M : 2016 Standard Test Method for Transverse Compressive Properties of Hoop Wound Polymer Matrix Composite Cylinders
    ASTM D 6416/D6416M : 2016 Standard Test Method for Two-Dimensional Flexural Properties of Simply Supported Sandwich Composite Plates Subjected to a Distributed Load
    ASTM D 7248/D7248M : 2012 : R2017 Standard Test Method for Bearing/Bypass Interaction Response of Polymer Matrix Composite Laminates Using 2-Fastener Specimens
    ASTM D 5379/D5379M : 2012 Standard Test Method for Shear Properties of Composite Materials by the V-Notched Beam Method
    ASTM D 4255/D4255M : 2015 : REV A Standard Test Method for In-Plane Shear Properties of Polymer Matrix Composite Materials by the Rail Shear Method
    ASTM D 7078/D7078M : 2012 Standard Test Method for Shear Properties of Composite Materials by V-Notched Rail Shear Method
    ASTM D 5450/D5450M : 2016 Standard Test Method for Transverse Tensile Properties of Hoop Wound Polymer Matrix Composite Cylinders
    ASTM D 5467/D5467M : 1997 : R2017 Standard Test Method for Compressive Properties of Unidirectional Polymer Matrix Composite Materials Using a Sandwich Beam
    ASTM D 3039/D3039M : 2017 Standard Test Method for Tensile Properties of Polymer Matrix Composite Materials
    ASTM E 1949 : 2003 : R2014 : EDT 1 Standard Test Method for Ambient Temperature Fatigue Life of Metallic Bonded Resistance Strain Gages
    ASTM E 1012 : 2014 : EDT 1 Standard Practice for Verification of Testing Frame and Specimen Alignment Under Tensile and Compressive Axial Force Application
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective