EN 12629-1:2000+A1:2010
Current
Current
The latest, up-to-date edition.
Machines for the manufacture of constructional products from concrete and calcium-silicate - Safety - Part 1: Common requirements
Published date
01-09-2010
Publisher
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 List of significant hazards
5 Safety requirements and/or protective measures
6 Verification of safety measures and/or provisions
7 Information for use
8 Marking
Annex A (informative) - Examples of machines for the
manufacture of constructional products from
concrete and calcium silicate
Annex B (informative) - Guarding examples
Annex ZA (informative) - Relationship between this
European Standard and the Essential Requirements
of EU Directive 2006/42/EC
Bibliography
This European Standard applies to machines for the manufacture of constructional products from concrete and/or calcium silicate examples of which are listed in annex A of this part. It gives concepts and general and common requirements for the design, operation and maintenance of such machines.1.2This European Standard deals with hazards listed in Clause 4 which can arise during the operation and maintenance, including the interfaces, of the machines for the manufacture of constructional products from concrete and calcium silicate, when carried out as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer.Part 2 to 8 of this standard give additional specific requirements and therefore have to be applied together with this part.1.3The preparation of concrete and/or calcium-silicate mixture and the transport from the mixer to the manufacturing plant are not part of this European Standard (see EN 12151:2007). The equipment for the transport and handling of formed products, other than the integrated transport system, is not covered by this stand1.4At the time of drafting, machine specific noise test codes for EN 12629-2 to -8 are not available to fulfill the requirements of 5.7.2 and 7.4.2. When they are available, they will be incorporated in these standards.1.5This document is not applicable to machines for the manufacture of constructional products from concrete and/or calcium silicate, which are manufactured before the date of publication of this document by CEN.
| Committee |
CEN/TC 151
|
| DevelopmentNote |
2000 Edition Re-Issued in September 2010 & incorporates AMD 1 2010. (09/2010)
|
| DocumentType |
Standard
|
| PublisherName |
Comite Europeen de Normalisation
|
| Status |
Current
|
| Standards | Relationship |
| PN EN 12629-1 : 2002 + A1 2010 | Identical |
| NBN EN 12629-1 : 2000 + A1 2010 | Identical |
| UNE-EN 12629-1:2001 | Identical |
| I.S. EN 12629-1:2000 | Identical |
| NS EN 12629-1 : 2000 + A1 2010 | Identical |
| BS EN 12629-1 : 2001 | Identical |
| SN EN 12629-1 : 2000 + A1 2010 | Identical |
| NEN EN 12629-1 : 2000 + A1 2010 | Identical |
| NF EN 12629-1 : 2000 + A1 2010 | Identical |
| DIN EN 12629-1:2011-01 | Identical |
| BS EN 12629-1 : 2000 | Identical |
| UNI EN 12629-1 : 2010 | Identical |
| UNE-EN 12629-1:2001+A1:2013 | Identical |
| BS EN 12629-1:2000+A1:2010 | Identical |
| UNE-EN 12629-1:2000+A1:2010 | Identical |
| BS EN 12629-3 : 2002 | MACHINES FOR THE MANUFACTURE OF CONSTRUCTIONAL PRODUCTS FROM CONCRETE AND CALCIUM-SILICATE - SAFETY - PART 3: SLIDE AND TURNTABLE MACHINES |
| BS EN 12629-7 : 2004 | MACHINES FOR THE MANUFACTURE OF CONSTRUCTIONAL PRODUCTS FROM CONCRETE AND CALCIUM-SILICATE - SAFETY - PART 7: STATIONARY AND MOBILE EQUIPMENT FOR LONG LINE MANUFACTURE OF PRESTRESSED PRODUCTS |
| I.S. EN 12629-4:2001 | MACHINES FOR THE MANUFACTURE OF CONSTRUCTIONAL PRODUCTS FROM CONCRETE AND CALCIUM-SILICATE - SAFETY - PART 4: CONCRETE ROOF TILE MAKING MACHINES |
| I.S. EN 12629-5-3:2004 | MACHINES FOR THE MANUFACTURE OF CONSTRUCTIONAL PRODUCTS FROM CONCRETE AND CALCIUM-SILICATE - SAFETY - PART 5-3: PIPE PRESTRESSING MACHINES |
| I.S. EN 12629-8:2003 | MACHINES FOR THE MANUFACTURE OF CONSTRUCTIONAL PRODUCTS FROM CONCRETE AND CALCIUM-SILICATE - SAFETY - PART 8: MACHINES AND EQUIPMENT FOR THE MANUFACTURE OF CONSTRUCTIONAL PRODUCTS FROM CALCIUM-SILICATE (AND CONCRETE) |
| EN 12629-8:2002+A1:2010 | Machines for the manufacture of constructional products from concrete and calcium-silicate - Safety - Part 8: Machines and equipment for the manufacture of constructional products from calcium-silicate (and concrete) |
| EN 12629-5-3:2003+A1:2010 | Machines for the manufacture of constructional products from concrete and calcium-silicate - Safety - Part 5-3: Pipe prestressing machines |
| EN 12629-5-4:2003+A1:2010 | Machines for the manufacture of constructional products from concrete and calcium-silicate - Safety - Part 5-4: Concrete pipe coating machines |
| EN 12629-5-1:2003+A1:2010 | Machines for the manufacture of constructional products from concrete and calcium-silicate - Safety - Part 5-1: Pipe making machines manufacturing in the vertical axis |
| EN 12629-3:2002+A1:2010 | Machines for the manufacture of constructional products from concrete and calcium-silicate - Safety - Part 3: Slide and turntable machines |
| BS EN 12629-6 : 2004 | MACHINES FOR THE MANUFACTURE OF CONSTRUCTIONAL PRODUCTS FROM CONCRETE AND CALCIUM-SILICATE - SAFETY - PART 6: STATIONARY AND MOBILE EQUIPMENT FOR THE MANUFACTURE OF PRECAST REINFORCED PRODUCTS |
| I.S. EN 12629-6:2004 | MACHINES FOR THE MANUFACTURE OF CONSTRUCTIONAL PRODUCTS FROM CONCRETE AND CALCIUM-SILICATE - SAFETY - PART 6: STATIONARY AND MOBILE EQUIPMENT FOR THE MANUFACTURE OF PRECAST REINFORCED PRODUCTS |
| I.S. EN 12629-2:2003 | MACHINES FOR THE MANUFACTURE OF CONSTRUCTIONAL PRODUCTS FROM CONCRETE AND CALCIUM-SILICATE - SAFETY - PART 2: BLOCK MAKING MACHINES |
| I.S. EN 12629-5-1:2004 | MACHINES FOR THE MANUFACTURE OF CONSTRUCTIONAL PRODUCTS FROM CONCRETE AND CALCIUM-SILICATE - SAFETY - PART 5-1: PIPE MAKING MACHINES MANUFACTURING IN THE VERTICAL AXIS |
| I.S. EN 12629-3:2002 | MACHINES FOR THE MANUFACTURE OF CONSTRUCTIONAL PRODUCTS FROM CONCRETE AND CALCIUM-SILICATE - SAFETY - PART 3: SLIDE AND TURNTABLE MACHINES |
| I.S. EN 12629-5-2:2004 | MACHINES FOR THE MANUFACTURE OF CONSTRUCTIONAL PRODUCTS FROM CONCRETE AND CALCIUM-SILICATE - SAFETY - PART 5-2: PIPE MAKING MACHINES MANUFACTURING IN THE HORIZONTAL AXIS |
| I.S. EN 12629-5-4:2004 | MACHINES FOR THE MANUFACTURE OF CONSTRUCTIONAL PRODUCTS FROM CONCRETE AND CALCIUM-SILICATE - SAFETY - PART 5-4: CONCRETE PIPE COATING MACHINES |
| I.S. EN 12629-7:2004 | MACHINES FOR THE MANUFACTURE OF CONSTRUCTIONAL PRODUCTS FROM CONCRETE AND CALCIUM-SILICATE - SAFETY - PART 7: STATIONARY AND MOBILE EQUIPMENT FOR LONG LINE MANUFACTURE OF PRESTRESSED PRODUCTS |
| DIN EN 12629-6:2011-02 | Machines for the manufacture of constructional products from concrete and calcium-silicate - Safety - Part 6: Stationary and mobile equipment for the manufacture of precast reinforced products (includes Amendment A1:2010) |
| BS EN 12629-5-4 : 2003 | MACHINES FOR THE MANUFACTURE OF CONSTRUCTIONAL PRODUCTS FROM CONCRETE AND CALCIUM-SILICATE - SAFETY - PART 5-4: CONCRETE PIPE COATING MACHINES |
| EN 12629-4:2001+A1:2010 | Machines for the manufacture of constructional products from concrete and calcium-silicate - Safety - Part 4:Concrete roof tile making machines |
| EN 12629-7:2004+A1:2010 | Machines for the manufacture of constructional products from concrete and calcium-silicate - Safety - Part 7: Stationary and mobile equipment for long line manufacture of prestressed products |
| UNI EN 12629-3 : 2010 | MACHINES FOR THE MANUFACTURE OF CONSTRUCTIONAL PRODUCTS FROM CONCRETE AND CALCIUM-SILICATE - SAFETY - PART 3: SLIDE AND TURNTABLE MACHINES |
| UNI EN 12629-5-4 : 2010 | MACHINES FOR THE MANUFACTURE OF CONSTRUCTIONAL PRODUCTS FROM CONCRETE AND CALCIUM-SILICATE - SAFETY - PART 5-4: CONCRETE PIPE COATING MACHINES |
| UNI EN 12629-5-3 : 2010 | MACHINES FOR THE MANUFACTURE OF CONSTRUCTIONAL PRODUCTS FROM CONCRETE AND CALCIUM-SILICATE - SAFETY - PART 5-3: PIPE PRESTRESSING MACHINES |
| UNI EN 12629-6 : 2010 | MACHINES FOR THE MANUFACTURE OF CONSTRUCTIONAL PRODUCTS FROM CONCRETE AND CALCIUM-SILICATE - SAFETY - PART 6: STATIONARY AND MOBILE EQUIPMENT FOR THE MANUFACTURE OF PRECAST REINFORCED PRODUCTS |
| UNI EN 12629-2 : 2010 | MACHINES FOR THE MANUFACTURE OF CONSTRUCTIONAL PRODUCTS FROM CONCRETE AND CALCIUM-SILICATE - SAFETY - PART 2: BLOCK MAKING MACHINES |
| UNI EN 12629-4 : 2010 | MACHINES FOR THE MANUFACTURE OF CONSTRUCTIONAL PRODUCTS FROM CONCRETE AND CALCIUM-SILICATE - SAFETY - PART 4: CONCRETE ROOF TILE MAKING MACHINES |
| UNI EN 12629-7 : 2010 | MACHINES FOR THE MANUFACTURE OF CONSTRUCTIONAL PRODUCTS FROM CONCRETE AND CALCIUM-SILICATE - SAFETY - PART 7: STATIONARY AND MOBILE EQUIPMENT FOR LONG LINE MANUFACTURE OF PRESTRESSED PRODUCTS |
| UNI EN 12629-5-2 : 2010 | MACHINES FOR THE MANUFACTURE OF CONSTRUCTIONAL PRODUCTS FROM CONCRETE AND CALCIUM-SILICATE - SAFETY - PART 5-2: PIPE MAKING MACHINES MANUFACTURING IN THE HORIZONTAL AXIS |
| UNI EN 12629-5-1 : 2010 | MACHINES FOR THE MANUFACTURE OF CONSTRUCTIONAL PRODUCTS FROM CONCRETE AND CALCIUM-SILICATE - SAFETY - PART 5-1: PIPE MAKING MACHINES MANUFACTURING IN THE VERTICAL AXIS |
| UNI EN 12629-8 : 2010 | MACHINES FOR THE MANUFACTURE OF CONSTRUCTIONAL PRODUCTS FROM CONCRETE AND CALCIUM-SILICATE - SAFETY - PART 8: MACHINES AND EQUIPMENT FOR THE MANUFACTURE OF CONSTRUCTIONAL PRODUCTS FROM CALCIUM-SILICATE (AND CONCRETE) |
| DIN EN 12629-5-2:2011-02 | Machines for the manufacture of constructional products from concrete and calcium-silicate - Safety - Part 5-2: Pipe making machines manufacturing in the horizontal axis (includes Amendment 2:2010) |
| DIN EN 12629-5-1:2011-02 | Machines for the manufacture of constructional products from concrete and calcium-silicate - Safety - Part 5-1: Pipe making machines manufacturing in the vertical axis (includes Amendment 1:2010) |
| DIN EN 12629-2:2011-01 | Machines for the manufacture of constructional products from concrete and calcium-silicate - Safety - Part 2: Block making machines (includes Amendment A1:2010) |
| DIN EN 12629-5-4:2011-02 | Machines for the manufacture of constructional products from concrete and calcium-silicate - Safety - Part 5-4: Concrete pipe coating machines (includes Amendment 4:2010) |
| DIN EN 12629-3:2011-02 | Machines for the manufacture of constructional products from concrete and calcium-silicate - Safety - Part 3: Slide and turntable machines (includes Amendment A1:2010) |
| DIN EN 12629-7:2011-03 | Machines for the manufacture of constructional products from concrete and calcium-silicate - Safety - Part 7: Stationary and mobile equipment for long line manufacture of prestressed products (includes Amendment A1:2010) |
| BS EN 12629-2 : 2002 | MACHINES FOR THE MANUFACTURE OF CONSTRUCTIONAL PRODUCTS FROM CONCRETE AND CALCIUM-SILICATE - SAFETY - PART 2: BLOCK MAKING MACHINES |
| BS EN 12629-5-1 : 2003 | MACHINES FOR THE MANUFACTURE OF CONSTRUCTIONAL PRODUCTS FROM CONCRETE AND CALCIUM-SILICATE - SAFETY - PART 5-1: PIPE MAKING MACHINES MANUFACTURING IN THE VERTICAL AXIS |
| EN 12629-5-2:2003+A1:2010 | Machines for the manufacture of constructional products from concrete and calcium-silicate - Safety - Part 5-2: Pipe making machines manufacturing in the horizontal axis |
| DIN EN 12629-5-3:2011-02 | Machines for the manufacture of constructional products from concrete and calcium-silicate - Safety - Part 5-3: Pipe prestressing machines (includes Amendment 3:2010) |
| BS EN 12629-5-2 : 2003 | MACHINES FOR THE MANUFACTURE OF CONSTRUCTIONAL PRODUCTS FROM CONCRETE AND CALCIUM-SILICATE - SAFETY - PART 5-2: PIPE MAKING MACHINES MANUFACTURING IN THE HORIZONTAL AXIS |
| BS EN 12629-8 : 2002 | MACHINES FOR THE MANUFACTURE OF CONSTRUCTIONAL PRODUCTS FROM CONCRETE AND CALCIUM-SILICATE - SAFETY - PART 8: MACHINES AND EQUIPMENT FOR THE MANUFACTURE OF CONSTRUCTIONAL PRODUCTS FROM CALCIUM-SILICATE (AND CONCRETE) |
| BS EN 12629-5-3 : 2003 | MACHINES FOR THE MANUFACTURE OF CONSTRUCTIONAL PRODUCTS FROM CONCRETE AND CALCIUM-SILICATE - SAFETY - PART 5-3: PIPE PRESTRESSING MACHINES |
| BS EN 12629-4 : 2001 | MACHINES FOR THE MANUFACTURE OF CONSTRUCTIONAL PRODUCTS FROM CONCRETE AND CALCIUM-SILICATE - SAFETY - PART 4: CONCRETE ROOF TILE MAKING MACHINES |
| EN 12629-6:2004+A1:2010 | Machines for the manufacture of constructional products from concrete and calcium-silicate - Safety - Part 6: Stationary and mobile equipment for the manufacture of precast reinforced products |
| EN 12629-2:2002+A1:2010 | Machines for the manufacture of constructional products from concrete and calcium-silicate - Safety - Part 2: Block making machines |
| UNE-EN 12629-6:2005 | Machines for the manufacture of constructional products from concrete and calcium-silicate - Safety - Part 6: Stationary and mobile equipment for the manufacture of precast reinforced products |
| UNE-EN 12629-7:2005 | Machines for the manufacture of constructional products from concrete and calcium-silicate - Safety - Part 7: Stationary and mobile equipment for long line manufacture of prestressed products |
| EN ISO 11204:2010 | Acoustics - Noise emitted by machinery and equipment - Determination of emission sound pressure levels at a work station and at other specified positions applying accurate environmental corrections (ISO 11204:2010) |
| EN 1339:2003/AC:2006 | CONCRETE PAVING FLAGS - REQUIREMENTS AND TEST METHODS |
| EN 894-3:2000+A1:2008 | Safety of machinery - Ergonomics requirements for the design of displays and control actuators - Part 3: Control actuators |
| EN 982:1996+A1:2008 | Safety of machinery - Safety requirements for fluid power systems and their components - Hydraulics |
| EN 1037:1995+A1:2008 | Safety of machinery - Prevention of unexpected start-up |
| ISO 14122-3:2016 | Safety of machinery — Permanent means of access to machinery — Part 3: Stairs, stepladders and guard-rails |
| EN 547-2:1996+A1:2008 | Safety of machinery - Human body measurements - Part 2: Principles for determining the dimensions required for access openings |
| ISO 14122-1:2016 | Safety of machinery — Permanent means of access to machinery — Part 1: Choice of fixed means and general requirements of access |
| EN 1088:1995+A2:2008 | Safety of machinery - Interlocking devices associated with guards - Principles for design and selection |
| IEC 61310-2:2007 | Safety of machinery - Indication, marking and actuation - Part 2: Requirements for marking |
| EN 981:1996+A1:2008 | Safety of machinery - System of auditory and visual danger and information signals |
| ISO/TR 11688-1:1995 | Acoustics Recommended practice for the design of low-noise machinery and equipment Part 1: Planning |
| EN 894-2:1997+A1:2008 | Safety of machinery - Ergonomics requirements for the design of displays and control actuators - Part 2: Displays |
| EN 61310-2:2008 | Safety of machinery - Indication, marking and actuation - Part 2: Requirements for marking |
| EN 999:1998+A1:2008 | Safety of machinery - The positioning of protective equipment in respect of approach speeds of parts of the human body |
| EN 349:1993+A1:2008 | Safety of machinery - Minimum gaps to avoid crushing of parts of the human body |
| IEC 60204-1:2016 | Safety of machinery - Electrical equipment of machines - Part 1: General requirements |
| EN 547-1:1996+A1:2008 | Safety of machinery - Human body measurements - Part 1: Principles for determining the dimensions required for openings for whole body access into machinery |
| EN ISO 13850:2015 | Safety of machinery - Emergency stop function - Principles for design (ISO 13850:2015) |
| EN 1340:2003/AC:2006 | CONCRETE KERB UNITS - REQUIREMENTS AND TEST METHODS |
| EN 614-1:2006+A1:2009 | Safety of machinery - Ergonomic design principles - Part 1: Terminology and general principles |
| EN ISO 13857:2008 | Safety of machinery - Safety distances to prevent hazard zones being reached by upper and lower limbs (ISO 13857:2008) |
| ISO 14122-4:2016 | Safety of machinery — Permanent means of access to machinery — Part 4: Fixed ladders |
| EN 574:1996+A1:2008 | Safety of machinery - Two-hand control devices - Functional aspects - Principles for design |
| EN 12151:2007 | Machinery and plants for the preparation of concrete and mortar - Safety requirements |
| ISO 3746:2010 | Acoustics Determination of sound power levels and sound energy levels of noise sources using sound pressure Survey method using an enveloping measurement surface over a reflecting plane |
| EN ISO 12100-1:2003/A1:2009 | SAFETY OF MACHINERY - BASIC CONCEPTS, GENERAL PRINCIPLES FOR DESIGN - PART 1: BASIC TERMINOLOGY, METHODOLOGY |
| EN ISO 14122-3:2016 | Safety of machinery - Permanent means of access to machinery - Part 3: Stairs, stepladders and guard-rails (ISO 14122-3:2016) |
| EN ISO 3746:2010 | Acoustics - Determination of sound power levels and sound energy levels of noise sources using sound pressure - Survey method using an enveloping measurement surface over a reflecting plane (ISO 3746:2010) |
| EN 61496-1:2013/AC:2015 | SAFETY OF MACHINERY - ELECTRO-SENSITIVE PROTECTIVE EQUIPMENT - PART 1: GENERAL REQUIREMENTS AND TESTS (IEC 61496-1:2012) |
| EN 953:1997+A1:2009 | Safety of machinery - Guards - General requirements for the design and construction of fixed and movable guards |
| EN 547-3:1996+A1:2008 | Safety of machinery - Human body measurements - Part 3: Anthropometric data |
| EN ISO 14122-4:2016 | Safety of machinery - Permanent means of access to machinery - Part 4: Fixed ladders (ISO 14122-4:2016) |
| EN ISO 14122-2:2016 | Safety of machinery - Permanent means of access to machinery - Part 2: Working platforms and walkways (ISO 14122-2:2016) |
| ISO 12100-2:2003 | Safety of machinery Basic concepts, general principles for design Part 2: Technical principles |
| ISO 13857:2008 | Safety of machinery Safety distances to prevent hazard zones being reached by upper and lower limbs |
| EN ISO 12100-2:2003/A1:2009 | SAFETY OF MACHINERY - BASIC CONCEPTS, GENERAL PRINCIPLES FOR DESIGN - PART 2: TECHNICAL PRINCIPLES |
| IEC 61496-1:2012 | Safety of machinery - Electro-sensitive protective equipment - Part 1: General requirements and tests |
| EN 983:1996+A1:2008 | Safety of machinery - Safety requirements for fluid power systems and their components - Pneumatics |
| EN 954-1 : 1996 | SAFETY OF MACHINERY - SAFETY-RELATED PARTS OF CONTROL SYSTEMS - PART 1: GENERAL PRINCIPLES FOR DESIGN |
| ISO 12100-1:2003 | Safety of machinery Basic concepts, general principles for design Part 1: Basic terminology, methodology |
| ISO 13850:2015 | Safety of machinery Emergency stop function Principles for design |
| IEC 61310-1:2007 | Safety of machinery - Indication, marking and actuation - Part 1: Requirements for visual, acoustic and tactile signals |
| EN 626-1:1994+A1:2008 | Safety of machinery - Reduction of risks to health from hazardous substances emitted by machinery - Part 1: Principles and specifications for machinery manufacturers |
| EN 457 : 1992 | SAFETY OF MACHINERY - AUDITORY DANGER SIGNALS - GENERAL REQUIREMENTS, DESIGN AND TESTING |
| ISO 14122-2:2016 | Safety of machinery — Permanent means of access to machinery — Part 2: Working platforms and walkways |
| EN ISO 11688-1:2009 | Acoustics - Recommended practice for the design of low-noise machinery and equipment - Part 1: Planning (ISO/TR 11688-1:1995) |
| EN ISO 14122-1:2016 | Safety of machinery - Permanent means of access to machinery - Part 1: Choice of fixed means and general requirements of access (ISO 14122-1:2016) |
| EN 61310-1:2008 | Safety of machinery - Indication, marking and actuation - Part 1: Requirements for visual, acoustic and tactile signals |
| ISO 11204:2010 | Acoustics Noise emitted by machinery and equipment Determination of emission sound pressure levels at a work station and at other specified positions applying accurate environmental corrections |
| EN 60204-1 : 2006 COR 2010 | SAFETY OF MACHINERY - ELECTRICAL EQUIPMENT OF MACHINES - PART 1: GENERAL REQUIREMENTS |
| EN 894-1:1997+A1:2008 | Safety of machinery - Ergonomics requirements for the design of displays and control actuators - Part 1: General principles for human interactions with displays and control actuators |
Sorry this product is not available in your region.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.