• There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

EN 1870-14:2007+A2:2012

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Safety of woodworking machines - Circular sawing machines - Part 14: Vertical panel sawing machines
Superseded date

23-03-2022

Published date

28-03-2012

Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 List of significant hazards
5 Safety requirements and/or measures
6 Information for use
Annex A (normative) - Impact test method for guards
Annex B (normative) - Saw spindle dimensional tolerances
Annex C (normative) - Riving knife mounting strength test
Annex D (normative) - Riving knife testing - Lateral
        stability
Annex E (normative) - Braking tests
Annex ZA (informative) - Relationship between this European
       Standard and the Essential Requirements of EU
       Directive 2006/42/EC
Bibliography

This European Standard specifies all significant hazards, hazardous situations and events as listed in Clause 4 which are relevant to manually loaded and unloaded vertical panel sawing (with or without integrated feed) machines fitted with:-the facility for scoring;-an angle cutting device;-a middle support device;-a programmable stop for parallel vertical cuts;-the facility for grooving with a width of at most 20 mm in one pass by using a milling tools,hereinafter referred to as "machines" when they are used as intended and under the conditions foreseen by the manufacturer including reasonably foreseeable misuse.The machines are designed for cutting panels of the following materials:a)wood based materials such as chipboard, fibreboard, plywood and also these materials where they are covered with plastic / light alloy laminates;b)solid wood;c)hardened rubber and hardened plastic material;d)non ferrous materials e.g. light alloy;e)compound materials with core consisting of polyurethane or mineral material laminated with light alloy.This European Standard does not apply to vertical panel saws with pressure beam and saw unit mounted behind the workpiece support.This European Standard does not deal with hazards relating to the combination of a single machine being used with any other machine (as part of a line).This European Standard is not applicable to vertical panel saws which are manufactured before the date of its publication as EN.NOTEMachines covered by this standard are listed under A.1.4 of Annex IV of the Machinery Directive.

Committee
CEN/TC 142
DevelopmentNote
Together with EN 1870-13 supersedes EN 1870-2. (03/2008) 2007 Edition Re-Issued in March 2012 & incorporates AMD 2 2012. (04/2012)
DocumentType
Standard
PublisherName
Comite Europeen de Normalisation
Status
Superseded
SupersededBy
Supersedes

11/30248450 DC : 0 BS EN 847-3 - TOOLS FOR WOODWORKING - SAFETY REQUIREMENTS - PART 3: CLAMPING DEVICES
PREN 847-3 : DRAFT 2011 TOOLS FOR WOODWORKING - SAFETY REQUIREMENTS - PART 3: CLAMPING DEVICES
I.S. EN 847-3:2013 TOOLS FOR WOODWORKING - SAFETY REQUIREMENTS - PART 3: CLAMPING DEVICES
UNE-EN 847-3:2014 Tools for woodworking - Safety requirements - Part 3: Clamping devices
BS EN 847-3:2013 Tools for woodworking. Safety requirements Clamping devices
EN 847-3:2013 Tools for woodworking - Safety requirements - Part 3: Clamping devices
DIN EN 847-3:2013-12 TOOLS FOR WOODWORKING - SAFETY REQUIREMENTS - PART 3: CLAMPING DEVICES

EN 1005-4:2005+A1:2008 Safety of machinery - Human physical performance - Part 4: Evaluation of working postures and movements in relation to machinery
ISO 11202:2010 Acoustics Noise emitted by machinery and equipment Determination of emission sound pressure levels at a work station and at other specified positions applying approximate environmental corrections
EN ISO 11204:2010 Acoustics - Noise emitted by machinery and equipment - Determination of emission sound pressure levels at a work station and at other specified positions applying accurate environmental corrections (ISO 11204:2010)
EN 894-3:2000+A1:2008 Safety of machinery - Ergonomics requirements for the design of displays and control actuators - Part 3: Control actuators
ISO 4871:1996 Acoustics — Declaration and verification of noise emission values of machinery and equipment
EN 1037:1995+A1:2008 Safety of machinery - Prevention of unexpected start-up
ISO 3744:2010 Acoustics Determination of sound power levels and sound energy levels of noise sources using sound pressure Engineering methods for an essentially free field over a reflecting plane
EN 61800-5-2:2017 Adjustable speed electrical power drive systems - Part 5-2: Safety requirements - Functional
EN 1088:1995+A2:2008 Safety of machinery - Interlocking devices associated with guards - Principles for design and selection
EN ISO 3743-2:2009 Acoustics - Determination of sound power levels of noise sources using sound pressure - Engineering methods for small, movable sources in reverberant fields - Part 2: Methods for special reverberation test rooms (ISO 3743-2:1994)
ISO/TR 11688-1:1995 Acoustics Recommended practice for the design of low-noise machinery and equipment Part 1: Planning
EN 894-2:1997+A1:2008 Safety of machinery - Ergonomics requirements for the design of displays and control actuators - Part 2: Displays
ISO 3743-2:1994 Acoustics Determination of sound power levels of noise sources using sound pressure Engineering methods for small, movable sources in reverberant fields Part 2: Methods for special reverberation test rooms
ISO 7960:1995 Airborne noise emitted by machine tools Operating conditions for woodworking machines
EN 1093-9:1998+A1:2008 Safety of machinery - Evaluation of the emission of airborne hazardous substances - Part 9: Pollutant concentration parameter, room method
ISO 9614-1:1993 Acoustics — Determination of sound power levels of noise sources using sound intensity — Part 1: Measurement at discrete points
EN 614-2:2000+A1:2008 Safety of machinery - Ergonomic design principles - Part 2: Interactions between the design of machinery and work tasks
EN 50370-2:2003 Electromagnetic compatibility (EMC) - Product family standard for machine tools - Part 2: Immunity
IEC 60204-1:2016 Safety of machinery - Electrical equipment of machines - Part 1: General requirements
EN ISO 13850:2015 Safety of machinery - Emergency stop function - Principles for design (ISO 13850:2015)
EN 1005-1:2001+A1:2008 Safety of machinery - Human physical performance - Part 1: Terms and definitions
EN 1005-2:2003+A1:2008 Safety of machinery - Human physical performance - Part 2: Manual handling of machinery and component parts of machinery
EN 12779:2015 Safety of woodworking machines - Chip and dust extraction systems with fixed installation - Safety requirements
EN 1050 : 1996 SAFETY OF MACHINERY - PRINCIPLES FOR RISK ASSESSMENT
EN ISO 3745:2012/A1:2017 ACOUSTICS - DETERMINATION OF SOUND POWER LEVELS AND SOUND ENERGY LEVELS OF NOISE SOURCES USING SOUND PRESSURE - PRECISION METHODS FOR ANECHOIC ROOMS AND HEMI-ANECHOIC ROOMS (ISO 3745:2012/AMD 1:2017)
EN 614-1:2006+A1:2009 Safety of machinery - Ergonomic design principles - Part 1: Terminology and general principles
EN ISO 13857:2008 Safety of machinery - Safety distances to prevent hazard zones being reached by upper and lower limbs (ISO 13857:2008)
EN ISO 11688-2 : 2000 ACOUSTICS - RECOMMENDED PRACTICE FOR THE DESIGN OF LOW-NOISE MACHINERY AND EQUIPMENT - PART 2: INTRODUCTION TO THE PHYSICS OF LOW-NOISE DESIGN
EN 50178:1997 Electronic equipment for use in power installations
HD 22-1 : 200S4 CABLES OF RATED VOLTAGES UP TO AND INCLUDING 450/750 V AND HAVING THERMOSETTING INSULATION - GENERAL REQUIREMENTS
HD 21.1 : 200S4 CABLES OF RATED VOLTAGES UP TO AND INCLUDING 450/750 V AND HAVING THERMOPLASTIC INSULATION - GENERAL REQUIREMENTS
ISO 3746:2010 Acoustics Determination of sound power levels and sound energy levels of noise sources using sound pressure Survey method using an enveloping measurement surface over a reflecting plane
EN ISO 3746:2010 Acoustics - Determination of sound power levels and sound energy levels of noise sources using sound pressure - Survey method using an enveloping measurement surface over a reflecting plane (ISO 3746:2010)
EN 61496-1:2013/AC:2015 SAFETY OF MACHINERY - ELECTRO-SENSITIVE PROTECTIVE EQUIPMENT - PART 1: GENERAL REQUIREMENTS AND TESTS (IEC 61496-1:2012)
EN 60947-4-1 : 2010 AMD 1 2012 LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 4-1: CONTACTORS AND MOTOR-STARTERS - ELECTROMECHANICAL CONTACTORS AND MOTOR-STARTERS (IEC 60947-4-1:2009/A1:2012)
IEC 60529:1989+AMD1:1999+AMD2:2013 CSV Degrees of protection provided by enclosures (IP Code)
EN ISO 3744:2010 Acoustics - Determination of sound power levels and sound energy levels of noise sources using sound pressure - Engineering methods for an essentially free field over a reflecting plane (ISO 3744:2010)
EN ISO 4414:2010 Pneumatic fluid power - General rules and safety requirements for systems and their components (ISO 4414:2010)
IEC 60439-1:1999+AMD1:2004 CSV Low-voltage switchgear and controlgear assemblies - Part 1: Type-tested and partially type-tested assemblies
ISO 13849-2:2012 Safety of machinery — Safety-related parts of control systems — Part 2: Validation
ISO 13857:2008 Safety of machinery Safety distances to prevent hazard zones being reached by upper and lower limbs
IEC 61496-1:2012 Safety of machinery - Electro-sensitive protective equipment - Part 1: General requirements and tests
EN 60439-1:1999/A1:2004 LOW VOLTAGE SWITCHGEAR AND CONTROLGEAR ASSEMBLIES - PART 1 - TYPE TESTED AND PARTIALLY TYPE TESTED ASSEMBLIES
EN ISO 12100:2010 Safety of machinery - General principles for design - Risk assessment and risk reduction (ISO 12100:2010)
EN 847-1:2017 Tools for woodworking - Safety requirements - Part 1: Milling tools, circular saw blades
EN ISO 13849-2:2012 Safety of machinery - Safety-related parts of control systems - Part 2: Validation (ISO 13849-2:2012)
EN ISO 3743-1:2010 Acoustics - Determination of sound power levels and sound energy levels of noise sources using sound pressure - Engineering methods for small movable sources in reverberant fields - Part 1: Comparison method for a hard-walled test room (ISO 3743-1:2010)
EN ISO 13849-1:2015 Safety of machinery - Safety-related parts of control systems - Part 1: General principles for design (ISO 13849-1:2015)
ISO 4414:2010 Pneumatic fluid power General rules and safety requirements for systems and their components
ISO 13850:2015 Safety of machinery Emergency stop function Principles for design
EN ISO 4871:2009 Acoustics - Declaration and verification of noise emission values of machinery and equipment (ISO 4871:1996)
IEC 61310-1:2007 Safety of machinery - Indication, marking and actuation - Part 1: Requirements for visual, acoustic and tactile signals
EN 1005-3:2002+A1:2008 Safety of machinery - Human physical performance - Part 3: Recommended force limits for machinery operation
EN 60529:1991/AC:2016-12 DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) (IEC 60529 EDITION 2.2 CORRIGENDUM 2:2015)
ISO 3745:2012 Acoustics — Determination of sound power levels and sound energy levels of noise sources using sound pressure — Precision methods for anechoic rooms and hemi-anechoic rooms
1998/37/EC : 1998 DIRECTIVE 98/37/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL OF 22 JUNE 1998 ON THE APPROXIMATION OF THE LAWS OF THE MEMBER STATES RELATING TO MACHINERY
EN 50370-1 : 2005 Electromagnetic compatibility (EMC) - Product family standard for machine tools - Part 1: Emission
EN ISO 11688-1:2009 Acoustics - Recommended practice for the design of low-noise machinery and equipment - Part 1: Planning (ISO/TR 11688-1:1995)
ISO 13849-1:2015 Safety of machinery — Safety-related parts of control systems — Part 1: General principles for design
ISO/TR 11688-2:1998 Acoustics Recommended practice for the design of low-noise machinery and equipment Part 2: Introduction to the physics of low-noise design
EN 61310-1:2008 Safety of machinery - Indication, marking and actuation - Part 1: Requirements for visual, acoustic and tactile signals
EN ISO 9614-1:2009 Acoustics - Determination of sound power levels of noise sources using sound intensity - Part 1: Measurement at discrete points (ISO 9614-1:1993)
EN ISO 11202:2010 Acoustics - Noise emitted by machinery and equipment - Determination of emission sound pressure levels at a work station and at other specified positions applying approximate environmental corrections (ISO 11202:2010)
ISO 11204:2010 Acoustics Noise emitted by machinery and equipment Determination of emission sound pressure levels at a work station and at other specified positions applying accurate environmental corrections
EN 1093-11:2001+A1:2008 Safety of machinery - Evaluation of the emission of airborne hazardous substances - Part 11: Decontamination index
IEC 61800-5-2:2016 Adjustable speed electrical power drive systems - Part 5-2: Safety requirements - Functional
ISO 3743-1:2010 Acoustics Determination of sound power levels and sound energy levels of noise sources using sound pressure Engineering methods for small movable sources in reverberant fields Part 1: Comparison method for a hard-walled test room
EN 60204-1 : 2006 COR 2010 SAFETY OF MACHINERY - ELECTRICAL EQUIPMENT OF MACHINES - PART 1: GENERAL REQUIREMENTS
EN 894-1:1997+A1:2008 Safety of machinery - Ergonomics requirements for the design of displays and control actuators - Part 1: General principles for human interactions with displays and control actuators

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.