Customer Support: +44 (0)203 327 3140

Login to i2i Subscription Intertek.com
  • There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Go to AMERICAS site
Dismiss alert
Please enter a keyword to search
Advanced search
Home
NSAI
I.S. EN 14636-2:2009

I.S. EN 14636-2:2009

Current

Current

The latest, up-to-date edition.

PLASTICS PIPING SYSTEMS FOR NON-PRESSURE DRAINAGE AND SEWERAGE - POLYESTER RESIN CONCRETE (PRC) - PART 2: MANHOLES AND INSPECTION CHAMBERS

Available format(s)

Hardcopy , PDF

Language(s)

English

Published date

01-01-2009

Publisher

National Standards Authority of Ireland

Preview

For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.

Only cited Standards give presumption of conformance to New Approach Directives/Regulations.

Foreword
1 Scope
2 Normative references
3 Terms, definitions, symbols and abbreviations
4 General requirements
5 Manholes and inspection chamber units
6 Dangerous substances
7 Manufacturer's installation recommendations
8 Evaluation of conformity
Annex A (normative) - Determination of a chamber ring's or
                      shaft ring's crushing strength and
                      ring bending tensile strength using
                      a ring test piece
Annex B (normative) - Test method for the determination of a
                      chamber ring's or shaft ring's crushing
                      strength or the ring bending tensile
                      strength using test pieces sawn from a
                      ring
Annex C (normative) - Test method for the determination of
                      the vertical crushing strength of slabs
                      or tapers
Annex D (normative) - Test method for the determination of the
                      compressive strength of polyester resin
Annex E (normative) - Test method for the determination of the
                      resistance of installed steps to vertical
                      and horizontal loading
Annex F (normative) - Method for the assessment of the leak-tightness
                      of a manhole or inspection chamber and its
                      joints under short term exposure to internal
                      water pressure and negative pressure
Annex G (normative) - Test method for the determination of the
                      long-term crushing strength (50 years
                      evaluation point) of a chamber ring or a
                      shaft ring, including the effects of media
                      attack
Bibliography

Describes units made from polyester resin concrete, and their joints, for the construction of inspection chambers with inverts not exceeding 2 m deep and for manholes, intended to be used within a drain or sewer system operating without pressure.

DocumentType
Standard
Pages
62
PublisherName
National Standards Authority of Ireland
Status
Current

Standards Relationship
EN 14636-2:2009 Identical

EN ISO 3126:2005 Plastics piping systems - Plastics components - Determination of dimensions (ISO 3126:2005)
EN 13121-1:2003 GRP TANKS AND VESSELS FOR USE ABOVE GROUND - PART 1: RAW MATERIALS - SPECIFICATION CONDITIONS AND ACCEPTANCE CONDITIONS
EN 14636-1:2009 Plastics piping systems for non-pressure drainage and sewerage - Polyester resin concrete (PRC) - Part 1: Pipes and fittings with flexible joints
EN 681-1:1996/A3:2005 ELASTOMERIC SEALS - MATERIALS REQUIREMENTS FOR PIPE JOINT SEALS USED IN WATER AND DRAINAGE APPLICATIONS - PART 1: VULCANIZED RUBBER
ISO 75-2:2013 Plastics — Determination of temperature of deflection under load — Part 2: Plastics and ebonite
EN ISO 75-2:2013 Plastics - Determination of temperature of deflection under load - Part 2: Plastics and ebonite (ISO 75-2:2013)
ISO 3126:2005 Plastics piping systems Plastics components Determination of dimensions
EN 637:1994/AC:1995 PLASTICS PIPING SYSTEMS - GLASS REINFORCED PLASTICS COMPONENTS - DETERMINATION OF THE AMOUNTS OF CONSTITUENTS USING THE GRAVIMETRIC METHOD
EN 476:2011 General requirements for components used in drains and sewers
EN ISO 9001:2015 Quality management systems - Requirements (ISO 9001:2015)
EN 13101:2002 Steps for underground man entry chambers - Requirements, marking, testing and evaluation of conformity
ISO 9001:2015 Quality management systems — Requirements
EN 705:1994/AC:1995 PLASTICS PIPING SYSTEMS - GLASS-REINFORCED THERMOSETTING PLASTICS (GRP) PIPES AND FITTINGS - METHODS FOR REGRESSION ANALYSES AND THEIR USE

View more information
£90.60
Excluding VAT
GBP
CAD
CHF
CNY
DKK
EUR
GBP
HKD
IDR
INR
JPY
KRW
MXN
NOK
NZD
SEK
SGD
USD
ZAR
Hardcopy - English
PDF - English
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Learn more on subscription solutions

or

Get in touch with us