We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
  • ISO 75-2:2013

    Current The latest, up-to-date edition.
    Add to Watchlist
    This Standard has been added successfully to your Watchlist.
    Please visit My Watchlist to see all standards that you are watching.
    Please log in or to add this standard to your Watchlist.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    You need to be logged in to add this standard to your Watchlist.
    Please log in now or create an account to add.
    You already added this Product in the Watchlist.

    Plastics Determination of temperature of deflection under load Part 2: Plastics and ebonite

    Available format(s):  Hardcopy, PDF, PDF 3 Users, PDF 5 Users, PDF 9 Users

    Language(s):  French, English, Russian

    Published date:  09-04-2013

    Publisher:  International Organization for Standardization

    Add to Watchlist

    Add To Cart

    Abstract - (Show below) - (Hide below)

    ISO 75-2:2013 specifies three methods, using different values of constant flexural stress, which can be used for the determination of the temperature of deflection under load of plastics (including filled plastics and fibre-reinforced plastics in which the fibre length, prior to processing, is up to 7,5 mm) and ebonite:

    • method A, using a flexural stress of 1,80 MPa;
    • method B, using a flexural stress of 0,45 MPa;
    • method C, using a flexural stress of 8,00 MPa.

    General Product Information - (Show below) - (Hide below)

    Committee ISO/TC 61/SC 2
    Development Note Supersedes ISO 75 (04/2001) Supersedes ISO/DIS 75-2. (04/2013)
    Document Type Standard
    Publisher International Organization for Standardization
    Status Current
    Supersedes

    Standards Referenced By This Book - (Show below) - (Hide below)

    I.S. EN 13121-3:2016 GRP TANKS AND VESSELS FOR USE ABOVE GROUND - PART 3: DESIGN AND WORKMANSHIP
    I.S. EN ISO 10350-1:2017 PLASTICS - ACQUISITION AND PRESENTATION OF COMPARABLE SINGLE-POINT DATA - PART 1: MOULDING MATERIALS (ISO 10350-1:2017)
    BS EN ISO 16396-2:2017 Plastics. Polyamide (PA) moulding and extrusion materials Preparation of test specimens and determination of properties
    BS EN 16506 : 2014 SYSTEMS FOR RENOVATION OF DRAINS AND SEWERS - LINING WITH A RIGIDLY ANCHORED PLASTICS INNER LAYER (RAPL)
    SAE J 1639 : 1995(S2017) CLASSIFICATION SYSTEM FOR AUTOMOTIVE POLYAMIDE (PA) PLASTICS
    UNE-EN ISO 9988-2:2015 Plastics - Polyoxymethylene (POM) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 9988-2:2006)
    PREN ISO 7792-2 : DRAFT 2011 PLASTICS - THERMOPLASTIC POLYESTER (TP) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES
    I.S. EN ISO 7792-2:2012 PLASTICS - THERMOPLASTIC POLYESTER (TP) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 7792-2:2012)
    ISO 16611:2017 Plastics piping systems for drainage and sewerage without pressure — Non-circular pipes and joints made of glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resins (UP) — Dimensions, requirements and tests
    DIN EN 16506 E : 2014 SYSTEMS FOR RENOVATION OF DRAINS AND SEWERS - LINING WITH A RIGIDLY ANCHORED PLASTICS INNER LAYER (RAPL)