|
EN ISO 3126:2005
|
Plastics piping systems - Plastics components - Determination of dimensions (ISO 3126:2005)
|
|
ISO/TR 10358:1993
|
Plastics pipes and fittings Combined chemical-resistance classification table
|
|
EN 681-1:1996/A3:2005
|
ELASTOMERIC SEALS - MATERIALS REQUIREMENTS FOR PIPE JOINT SEALS USED IN WATER AND DRAINAGE APPLICATIONS - PART 1: VULCANIZED RUBBER
|
|
ISO 13953:2001
|
Polyethylene (PE) pipes and fittings — Determination of the tensile strength and failure mode of test pieces from a butt-fused joint
|
|
EN 12201-4:2012
|
Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 4: Valves
|
|
ISO 13956:2010
|
Plastics pipes and fittings Decohesion test of polyethylene (PE) saddle fusion joints Evaluation of ductility of fusion joint interface by tear test
|
|
89/106/EEC : 1988
|
COUNCIL DIRECTIVE OF 21 DECEMBER 1988 ON THE APPROXIMATION OF LAWS, REGULATIONS AND ADMINISTRATIVE PROVISIONS OF THE MEMBER STATES RELATING TO CONSTRUCTION PRODUCTS
|
|
EN ISO 1167-1:2006
|
Thermoplastics pipes, fittings and assemblies for the conveyance of fluids - Determination of the resistance to internal pressure - Part 1: General method (ISO 1167-1:2006)
|
|
ISO 1167-4:2007
|
Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 4: Preparation of assemblies
|
|
ISO 12176-1:2017
|
Plastics pipes and fittings — Equipment for fusion jointing polyethylene systems — Part 1: Butt fusion
|
|
ISO 4433-1:1997
|
Thermoplastics pipes — Resistance to liquid chemicals — Classification — Part 1: Immersion test method
|
|
IEC 60364-1:2005
|
Low-voltage electrical installations - Part 1: Fundamental principles, assessment of general characteristics, definitions
|
|
EN 1716:1997
|
Plastics piping systems - Polyethylene (PE) tapping tees - Test method for impact resistance of an assembled tapping tee
|
|
CEN/TR 15438:2007
|
Plastics piping systems - Guidance for coding of products and their intended uses
|
|
ISO 3126:2005
|
Plastics piping systems Plastics components Determination of dimensions
|
|
ISO 11922-1:1997
|
Thermoplastics pipes for the conveyance of fluids — Dimensions and tolerances — Part 1: Metric series
|
|
EN ISO 1167-4:2007
|
Thermoplastics pipes, fittings and assemblies for the conveyance of fluids - Determination of the resistance to internal pressure - Part 4: Preparation of assemblies (ISO 1167-4:2007)
|
|
ISO 14236:2000
|
Plastics pipes and fittings Mechanical-joint compression fittings for use with polyethylene pressure pipes in water supply systems
|
|
IEC 60529:1989+AMD1:1999+AMD2:2013 CSV
|
Degrees of protection provided by enclosures (IP Code)
|
|
EN 12201-5:2011
|
Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 5: Fitness for purpose of the system
|
|
ISO 4433-2:1997
|
Thermoplastics pipes — Resistance to liquid chemicals — Classification — Part 2: Polyolefin pipes
|
|
ISO 1167-3:2007
|
Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 3: Preparation of components
|
|
ISO 13954:1997
|
Plastics pipes and fittings Peel decohesion test for polyethylene (PE) electrofusion assemblies of nominal outside diameter greater than or equal to 90 mm
|
|
ISO 13955:1997
|
Plastics pipes and fittings Crushing decohesion test for polyethylene (PE) electrofusion assemblies
|
|
EN 12201-2:2011+A1:2013
|
Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 2: Pipes
|
|
ISO 11357-6:2008
|
Plastics Differential scanning calorimetry (DSC) Part 6: Determination of oxidation induction time (isothermal OIT) and oxidation induction temperature (dynamic OIT)
|
|
EN 60335-1:2012/A13:2017
|
HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - SAFETY - PART 1: GENERAL REQUIREMENTS (IEC 60335-1:2010, MODIFIED)
|
|
ISO 9624:1997
|
Thermoplastics pipes for fluids under pressure Mating dimensions of flange adapters and loose backing flanges
|
|
EN 60529:1991/AC:2016-12
|
DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) (IEC 60529 EDITION 2.2 CORRIGENDUM 2:2015)
|
|
EN ISO 1133:2005
|
PLASTICS - DETERMINATION OF THE MELT MASS-FLOW RATE (MFR) AND THE MELT VOLUME-FLOW RATE (MVR) OF THE THERMOPLASTICS
|
|
ISO 4059:1978
|
Polyethylene (PE) pipes — Pressure drop in mechanical pipe-jointing systems — Method of test and requirements
|
|
ISO 13950:2007
|
Plastics pipes and fittings Automatic recognition systems for electrofusion joints
|
|
EN 12201-1:2011
|
Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 1: General
|
|
ISO 1133:2005
|
Plastics Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics
|
|
ISO 13951:2015
|
Plastics piping systems Test method for the resistance of plastic pipe/pipe or pipe/fitting assemblies to tensile loading
|
|
CEN/TS 12201-7:2014
|
Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 7: Guidance for the assessment of conformity
|
|
EN ISO 1167-3:2007
|
Thermoplastics pipes, fittings and assemblies for the conveyance of fluids - Determination of the resistance to internal pressure - Part 3: Preparation of components (ISO 1167-3:2007)
|
|
ISO 1167-1:2006
|
Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 1: General method
|
Important note : All end users must be registered with an Account prior to user licenses being assigned.