• There are no items in your cart

ASTM A 27/A27M : 2017 : REDLINE

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Specification for Steel Castings, Carbon, for General Application
Available format(s)

PDF

Superseded date

05-02-2020

Language(s)

English

Published date

05-01-2017

CONTAINED IN VOL. 01.02, 2017 Defines carbon steel castings for general applications that require up to 70 ksi (485 MPa) minimum tensile strength.

1.1This specification covers carbon steel castings for general applications that require up to 70 ksi (485 MPa) minimum tensile strength.

Note 1:The grades covered by this specification represent materials that are suitable for assembly with other steel castings or wrought steel parts by fusion welding. It is not intended to imply that all these grades possess the same degree of weldability or that the same welding techniques can be used on all castings. It is the responsibility of the purchaser to establish for himself a suitable welding technique.

1.2Several grades and two classes of steel castings are covered, as indicated below. The grade and class desired shall be specified by the purchaser.

1.2.1Grade N-1—Chemical analysis only.

1.2.2Grade N-2—Heat treated but not mechanically tested.

1.2.3Grade U-60-30 [415-205]Mechanically tested but not heat treated.

1.2.4Grades 60-30 [415-205], 65-35 [450-240], 70-36 [485-250], and 70-40 [485-275]—Heat treated and mechanically tested.

1.2.5Class 1 and Class 2 steel castings shall be specified in accordance with 9.2.

1.3The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.

1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Committee
A 01
DevelopmentNote
Supersedes ASTM A 27. (04/2002)
DocumentType
Redline
Pages
5
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy

AWWA C301 : 2014 PRESTRESSED CONCRETE PRESSURE PIPE, STEEL-CYLINDER TYPE
CSA S16S1 : 2005 SUPPLEMENT NO. 1 TO CAN/CSA-S16-01, LIMIT STATES DESIGN OF STEEL STRUCTURES
MIL-DTL-613 Revision D:2014 Grapnels, Marine, Trip Wire, and Crash Truck
AISC 350 : 99 ERRATA 2001 LOAD AND RESISTANCE FACTOR DESIGN SPECIFICATION FOR STRUCTURAL STEEL BUILDINGS
ASTM F 2798 : 2009 Standard Specification for Sealless Lube Oil Pump with Oil Through Motor for Marine Applications
S6-14 Canadian Highway Bridge Design Code
ASTM F 2935 : 2012 Standard Specification for Chocks, Panama, Mooring Cast Steel
ASTM F 2798 : 2009 : R2018 Standard Specification for Sealless Lube Oil Pump with Oil Through Motor for Marine Applications
MIL-DTL-12632 Revision E:2016 LOUDSPEAKERS, PERMANENT MAGNET (ENCASED, 2-WATT, FUNGUS-, GUNBLAST-, AND IMMERSION-RESISTANT), GENERAL SPECIFICATION FOR
AASHTO LRFDLTS 1 : 1900 LRFD SPECIFICATIONS FOR STRUCTURAL SUPPORTS FOR HIGHWAY SIGNS, LUMINAIRES, AND TRAFFIC SIGNALS
ASTM F 765 : 1993 : R2017 Standard Specification for Wildcats, Ship Anchor Chain
MIL L 12632 : D LOUDSPEAKER, PERMANENT MAGNET (ENCASED, 2 WATT, FUNGUS, GUNBLAST, AND IMMERSION RESISTANT), GENERAL SPECIFICATION FOR
CSA S37 : 2013 ANTENNAS, TOWERS, AND ANTENNA-SUPPORTING STRUCTURES
ASTM F 2798 : 2009 : R2014 : EDT 1 Standard Specification for Sealless Lube Oil Pump with Oil Through Motor for Marine Applications
ASTM F 1510 : 2007 : R2013 Standard Specification for Rotary Positive Displacement Pumps, Ships Use
ASTM F 1106 : 1987 : R2012 Standard Specification for Warping Heads, Rope Handling (Gypsy Head, Capstan Head)
ASME A17.7 : 2007 : R2012 PERFORMANCE-BASED SAFETY CODE FOR ELEVATORS AND ESCALATORS
ASME A17.7 : 2007 PERFORMANCE-BASED SAFETY CODE FOR ELEVATORS AND ESCALATORS
ASTM C 361M : 2016 : REDLINE SPECIFICATION FOR REINFORCED CONCRETE LOW-HEAD PRESSURE PIPE [METRIC]
ASTM F 765 : 1993 : R1998 Standard Specification for Wildcats, Ship Anchor Chain
AWWA C507 : 2015 BALL VALVES, 6 IN. THROUGH 60 IN. (150 MM THROUGH 1,500 MM)
MIL-DTL-2 Revision G:2006 VALVES, CYLINDER, GAS (FOR COMPRESSED OR LIQUEFIED GASES), GENERAL SPECIFICATION FOR
ASTM F 765 : 1993 : R2006 Standard Specification for Wildcats, Ship Anchor Chain
ASTM F 937 : 1985 : R1991 Specification for Chocks, Ship Mooring Cast Steel (Withdrawn 1997)
ASTM F 1106 : 1987 : R1998 Standard Specification for Warping Heads, Rope Handling (Gypsy Head, Capstan Head)
ASTM A 781/A781M : 2018-02 SPECIFICATION FOR CASTINGS, STEEL AND ALLOY, COMMON REQUIREMENTS, FOR GENERAL INDUSTRIAL USE
API 650 : 2013 WELDED TANKS FOR OIL STORAGE
CSA B44.7 : 2007 : R2012 PERFORMANCE-BASED SAFETY CODE FOR ELEVATORS AND ESCALATORS
ASME A17.7-2007/CSA B44.7-07 (R2017) Performance-Based Safety Code for Elevators and Escalators (Bi-National standard, with ASME A17.7)
CSA B44.7 : 2007 PERFORMANCE-BASED SAFETY CODE FOR ELEVATORS AND ESCALATORS
ASTM F 765 : 1993 : R2012 : EDT 1 Standard Specification for Wildcats, Ship Anchor Chain
ASTM F 915 : 1985 Specification for Bitts, Ship Mooring, Cast Steel (Double Barrel) (Withdrawn 1995)
ASTM F 2936 : 2012 Standard Specification for Chocks, Ship Mooring, Cast Steel
AWWA E103 : 2015 HORIZONTAL AND VERTICAL LINE-SHAFT PUMPS
AWWA C509 : 2015 RESILIENT-SEATED GATE VALVES FOR WATER SUPPLY SERVICE
NFPA 22 : 2018 WATER TANKS FOR PRIVATE FIRE PROTECTION
ASTM F 1106 : 1987 : R2006 Standard Specification for Warping Heads, Rope Handling (Gypsy Head, Capstan Head)
ASTM F 1510 : 2007 Standard Specification for Rotary Positive Displacement Pumps, Ships Use
ASTM F 936 : 1985 : R1991 Specification for Chocks, Panama, Mooring Cast Steel (Withdrawn 1997)
CSA S16 : 2014 DESIGN OF STEEL STRUCTURES
API 650 : 2013+ADD 3 : 2018 WELDED TANKS FOR OIL STORAGE
API 650 CHINESE : 2013 WELDED TANKS FOR OIL STORAGE
AISC 335 : 89 SUPP 1 1999 SPECIFICATION FOR STRUCTURAL STEEL BUILDINGS - ALLOWABLE STRESS DESIGN, PLASTIC DESIGN
CSA S16.1 : 0 LIMIT STATES DESIGN OF STEEL STRUCTURES
WW-T-696 Revision E:1984 TRAPS, STEAM
ANSI/AWWA C300 : 2016 REINFORCED CONCRETE PRESSURE PIPE, STEEL - CYLINDER TYPE
AWWA C515 : 2015 REDUCED-WALL, RESILIENT-SEATED GATE VALVES FOR WATER SUPPLY SERVICE
AWWA C302 : 2016 REINFORCED CONCRETE PRESSURE PIPE, NONCYLINDER TYPE
AWS D5.2 : 1984 WELDED STEEL ELEVATED TANKS, STANDPIPES, AND RESERVOIRS FOR WATER STORAGE, STANDARD FOR,
ASTM C 361 : 2019 : REDLINE SPECIFICATION FOR REINFORCED CONCRETE LOW-HEAD PRESSURE PIPE

View more information
US$66.00
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.