• There are no items in your cart

ASTM D 4762 : 2018

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Guide for Testing Polymer Matrix Composite Materials
Available format(s)

Hardcopy , PDF

Superseded date

11-09-2023

Language(s)

English

Published date

08-07-2018

1.1This guide summarizes the application of ASTM standard test methods (and other supporting standards) to continuous-fiber reinforced polymer matrix composite materials. The most commonly used or most applicable ASTM standards are included, emphasizing use of standards of Committee D30 on Composite Materials.

1.2This guide does not cover all possible standards that could apply to polymer matrix composites and restricts discussion to the documented scope. Commonly used but non-standard industry extensions of test method scopes, such as application of static test methods to fatigue testing, are not discussed. A more complete summary of general composite testing standards, including non-ASTM test methods, is included in the Composite Materials Handbook (CMH-17).2 Additional specific recommendations for testing textile (fabric, braided) composites are contained in Guide D6856.

1.3This guide does not specify a system of measurement; the systems specified within each of the referenced standards shall apply as appropriate. Note that the referenced standards of ASTM Committee D30 are either SI-only or combined-unit standards with SI units listed first.

1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Committee
D 30
DocumentType
Guide
Pages
25
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

ASTM E 2533 : 2021 Standard Guide for Nondestructive Examination of Polymer Matrix Composites Used in Aerospace Applications
ASTM D 8509/D8509M : 2023 Standard Guide for Test Method Selection and Test Specimen Design for Bolted Joint Related Properties
ASTM D 8069 : 2017 : REV A Standard Test Method for Determining Flexural Modulus of Full Section Pultruded Fiber Reinforced Polymer (FRP) Composite Members with Doubly Symmetric Cross Sections under Bending
ASTM E 2533 : 2017 : EDT 1 Standard Guide for Nondestructive Testing of Polymer Matrix Composites Used in Aerospace Applications

ASTM D 5766/D5766M : 2023 Standard Test Method for Open-Hole Tensile Strength of Polymer Matrix Composite Laminates
ASTM D 6115 : 1997 Standard Test Method for Mode I Fatigue Delamination Growth Onset of Unidirectional Fiber-Reinforced Polymer Matrix Composites
ASTM D 256 : 2010 : R2018 Standard Test Methods for Determining the Izod Pendulum Impact Resistance of Plastics
ASTM E 1269 : 2001 Standard Test Method for Determining Specific Heat Capacity by Differential Scanning Calorimetry
ASTM D 3171 : 1999 Standard Test Methods for Constituent Content of Composite Materials
ASTM C 271/C271M : 2016 : R2022 : EDT 1 Standard Test Method for Density of Sandwich Core Materials
ASTM D 8132/D8132M : 2023 Standard Test Method for Determination of Prepreg Impregnation by Permeability Measurement
ASTM D 2471 : 1999 Standard Test Method for Gel Time and Peak Exothermic Temperature of Reacting Thermosetting Resins (Withdrawn 2008)
ASTM D 5449/D5449M : 2016 Standard Test Method for Transverse Compressive Properties of Hoop Wound Polymer Matrix Composite Cylinders
ASTM D 7249/D7249M : 2018 Standard Test Method for Facesheet Properties of Sandwich Constructions by Long Beam Flexure
ASTM D 6790/D6790M : 2016 Standard Test Method for Determining Poisson's Ratio of Honeycomb Cores
ASTM D 7248/D7248M : 2023 Standard Test Method for High Bearing - Low Bypass Interaction Response of Polymer Matrix Composite Laminates Using 2-Fastener Specimens
ASTM F 1645/F1645M : 2016 Standard Test Method for Water Migration in Honeycomb Core Materials
ASTM D 3418 : 2012 : EDT 1 Standard Test Method for Transition Temperatures and Enthalpies of Fusion and Crystallization of Polymers by Differential Scanning Calorimetry
ASTM D 7957/D7957M : 2017 Standard Specification for Solid Round Glass Fiber Reinforced Polymer Bars for Concrete Reinforcement
ASTM D 2583 : 2013 : REV A Standard Test Method for Indentation Hardness of Rigid Plastics by Means of a Barcol Impressor (Withdrawn 2022)
ASTM D 4065 : 2006 Standard Practice for Plastics: Dynamic Mechanical Properties: Determination and Report of Procedures
ASTM D 5449/D5449M : 2022 Standard Test Method for Transverse Compressive Properties of Hoop Wound Polymer Matrix Composite Cylinders
ASTM D 3418 : 1982 : R1988 : EDT 1 Standard Test Method for Transition Temperatures of Polymers By Thermal Analysis
ASTM D 6856 : 2003 Standard Guide for Testing Fabric-Reinforced "Textile" Composite Materials
ASTM D 8131/D8131M : 2017 : EDT 1 Standard Practice for Tensile Properties of Tapered and Stepped Joints of Polymer Matrix Composite Laminates
ASTM D 6742/D6742M : 2017 Standard Practice for Filled-Hole Tension and Compression Testing of Polymer Matrix Composite Laminates
ASTM D 6272 : 2010 Standard Test Method for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials by Four-Point Bending
ASTM D 8066/D8066M : 2023 Standard Practice Unnotched Compression Testing of Polymer Matrix Composite Laminates
ASTM D 2584 : 2002 Standard Test Method for Ignition Loss of Cured Reinforced Resins
ASTM D 5083 : 2010 Standard Test Method for Tensile Properties of Reinforced Thermosetting Plastics Using Straight-Sided Specimens
ASTM D 3800 : 1999 : R2004 Standard Test Method for Density of High-Modulus Fibers
ASTM D 3418 : 1999 Standard Test Method for Transition Temperatures of Polymers By Differential Scanning Calorimetry
ASTM D 4102 : 1982 : R1999 : EDT 1 Standard Test Method for Thermal Oxidative Resistance of Carbon Fibers
ASTM D 3846 : 2002 Standard Test Method for In-Plane Shear Strength of Reinforced Plastics
ASTM D 3878 : 2002 : REV A Standard Terminology for Composite Materials
ASTM D 6507 : 2019 Standard Practice for Fiber Reinforcement Orientation Codes for Composite Materials
ASTM D 5450/D5450M : 2022 Standard Test Method for Transverse Tensile Properties of Hoop Wound Polymer Matrix Composite Cylinders
ASTM E 228 : 2017 Standard Test Method for Linear Thermal Expansion of Solid Materials With a Push-Rod Dilatometer
ASTM D 3418 : 2021 Standard Test Method for Transition Temperatures and Enthalpies of Fusion and Crystallization of Polymers by Differential Scanning Calorimetry
ASTM E 1461 : 2011 Standard Test Method for Thermal Diffusivity by the Flash Method
ASTM E 1922 : 2004 : R2015 Standard Test Method for Translaminar Fracture Toughness of Laminated and Pultruded Polymer Matrix Composite Materials
ASTM D 5083 : 2002 Standard Test Method for Tensile Properties of Reinforced Thermosetting Plastics Using Straight-Sided Specimens
ASTM E 1461 : 2007 Standard Test Method for Thermal Diffusivity by the Flash Method
ASTM D 7332/D7332M : 2023 Standard Test Method for Measuring the Fastener Pull-Through Resistance of a <brk/>Fiber-Reinforced Polymer Matrix Composite
ASTM D 6772/D6772M : 2016 Standard Test Method for Dimensional Stability of Sandwich Core Materials
ASTM D 3878 : 2023 Standard Terminology for Composite Materials
ASTM E 1269 : 2005 Standard Test Method for Determining Specific Heat Capacity by Differential Scanning Calorimetry
ASTM D 5961/D5961M : 2023 Standard Test Method for Bearing Response of Polymer Matrix Composite Laminates
ASTM D 4018 : 2011 Standard Test Methods for Properties of Continuous Filament Carbon and Graphite Fiber Tows
ASTM D 5083 : 2010 : EDT 1 Standard Test Method for Tensile Properties of Reinforced Thermosetting Plastics Using Straight-Sided Specimens
ASTM D 8066/D8066M : 2017 Standard Practice Unnotched Compression Testing of Polymer Matrix Composite Laminates
ASTM D 5528 : 2001 Standard Test Method for Mode I Interlaminar Fracture Toughness of Unidirectional Fiber-Reinforced Polymer Matrix Composites
ASTM D 3878 : 2015 Standard Terminology for Composite Materials
ASTM D 3529 : 2016 : R2021 Standard Test Methods for Constituent Content of Composite Prepreg
ASTM D 2584 : 2008 Standard Test Method for Ignition Loss of Cured Reinforced Resins
ASTM C 273/C273M : 2006 Standard Test Method for Shear Properties of Sandwich Core Materials
ASTM D 7248/D7248M : 2012 : R2017 Standard Test Method for Bearing/Bypass Interaction Response of Polymer Matrix Composite Laminates Using 2-Fastener Specimens
ASTM D 3878 : 2019 Standard Terminology for Composite Materials
ASTM D 256 : 2023 : EDT 1 Standard Test Methods for Determining the Izod Pendulum Impact Resistance of Plastics
ASTM D 7750 : 2012 Standard Test Method for Cure Behavior of Thermosetting Resins by Dynamic Mechanical Procedures using an Encapsulated Specimen Rheometer
ASTM D 3878 : 2000 Standard Terminology Composite Materials
ASTM D 7332/D7332M : 2022 Standard Test Method for Measuring the Fastener Pull-Through Resistance of a <brk/>Fiber-Reinforced Polymer Matrix Composite
ASTM D 7028 : 2007 Standard Test Method for Glass Transition Temperature (DMA Tg) of Polymer Matrix Composites by Dynamic Mechanical Analysis (DMA)
ASTM D 7766/D7766M : 2016 Standard Practice for Damage Resistance Testing of Sandwich Constructions
ASTM D 6115 : 1997 : R2019 Standard Test Method for Mode I Fatigue Delamination Growth Onset of Unidirectional Fiber-Reinforced Polymer Matrix Composites
ASTM D 5528 : 1994 : REV A Standard Test Method for Mode I Interlaminar Fracture Toughness of Unidirectional Fiber-Reinforced Polymer Matrix Composites
ASTM D 7750 : 2023 Standard Test Method for Cure Behavior of Thermosetting Resins by Dynamic Mechanical Procedures using an Encapsulated Specimen Rheometer
ASTM D 4473 : 2003 Standard Test Method for Plastics: Dynamic Mechanical Properties: Cure Behavior
ASTM D 8131/D8131M : 2023 Standard Practice for Tensile Properties of Tapered and Stepped Joints of Polymer Matrix Composite Laminates
ASTM D 2584 : 1994 Standard Test Method for Ignition Loss of Cured Reinforced Resins
ASTM D 6742/D6742M : 2023 Standard Practice for Filled-Hole Tension and Compression Testing of Polymer Matrix Composite Laminates
ASTM D 5528 : 2001 : R2007 : EDT 3 Standard Test Method for Mode I Interlaminar Fracture Toughness of Unidirectional Fiber-Reinforced Polymer Matrix Composites
ASTM D 6264/D6264M : 2017 Standard Test Method for Measuring the Damage Resistance of a Fiber-Reinforced Polymer-Matrix Composite to a Concentrated Quasi-Static Indentation Force
ASTM D 2583 : 2006 Standard Test Method for Indentation Hardness of Rigid Plastics by Means of a Barcol Impressor
ASTM D 3171 : 2011 Standard Test Methods for Constituent Content of Composite Materials
ASTM D 3529 : 2016 Standard Test Methods for Constituent Content of Composite Prepreg
ASTM D 2344/D2344M : 2016 Standard Test Method for Short-Beam Strength of Polymer Matrix Composite Materials and Their Laminates
ASTM D 7291/D7291M : 2022 Standard Test Method for Through-Thickness “Flatwise” Tensile Strength and Elastic Modulus of a Fiber-Reinforced Polymer Matrix Composite Material
ASTM D 6790/D6790M : 2022 Standard Test Method for Determining Poisson&apos;s Ratio of Honeycomb Cores
ASTM F 1645/F1645M : 2022 Standard Test Method for Water Migration in Honeycomb Core Materials
ASTM D 8132/D8132M : 2017 Standard Test Method for Determination of Prepreg Impregnation by Permeability Measurement
ASTM D 6115 : 1997 : R2011 Standard Test Method for Mode I Fatigue Delamination Growth Onset of Unidirectional Fiber-Reinforced Polymer Matrix Composites
ASTM D 6484/D6484M : 2023 Standard Test Method for Open-Hole Compressive Strength of Polymer Matrix Composite Laminates
ASTM D 2734 : 2016 Standard Test Methods for Void Content of Reinforced Plastics
ASTM D 3846 : 1994 Standard Test Method for In-Plane Shear Strength of Reinforced Plastics
ASTM D 7264/D7264M : 2021 Standard Test Method for Flexural Properties of Polymer Matrix Composite Materials
ASTM D 543 : 2021 Standard Practices for Evaluating the Resistance of Plastics to Chemical Reagents
ASTM D 1505 : 2003 Standard Test Method for Density of Plastics by the Density-Gradient Technique
ASTM D 7205/D7205M : 2021 Standard Test Method for Tensile Properties of Fiber Reinforced Polymer Matrix Composite Bars
ASTM D 5448/D5448M : 2022 Standard Test Method for Inplane Shear Properties of Hoop Wound Polymer Matrix Composite Cylinders
ASTM D 2990 : 2017 Standard Test Methods for Tensile, Compressive, and Flexural Creep and Creep-Rupture of Plastics
ASTM D 3846 : 2008 Standard Test Method for In-Plane Shear Strength of Reinforced Plastics
ASTM E 1269 : 1999 Standard Test Method for Determining Specific Heat Capacity by Differential Scanning Calorimetry
ASTM D 3800 : 1999 : R2010 Standard Test Method for Density of High-Modulus Fibers
ASTM D 3418 : 2012 Standard Test Method for Transition Temperatures and Enthalpies of Fusion and Crystallization of Polymers by Differential Scanning Calorimetry
ASTM D 5379/D5379M : 2019 : EDT 1 Standard Test Method for Shear Properties of Composite Materials by the V-Notched Beam Method
ASTM D 4018 : 2017 Standard Test Methods for Properties of Continuous Filament Carbon and Graphite Fiber Tows
ASTM D 6272 : 2017 : EDT 1 Standard Test Method for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials by Four-Point Bending
ASTM D 3418 : 2003 Standard Test Method for Transition Temperatures and Enthalpies of Fusion and Crystallization of Polymers by Differential Scanning Calorimetry
ASTM D 4473 : 2008 : R2016 Standard Test Method for Plastics: Dynamic Mechanical Properties: Cure Behavior
ASTM D 5083 : 1996 Standard Test Method for Tensile Properties of Reinforced Thermosetting Plastics Using Straight-Sided Specimens
ASTM D 2583 : 2013 Standard Test Method for Indentation Hardness of Rigid Plastics by Means of a Barcol Impressor
ASTM D 3878 : 2003 : REV A Standard Terminology for Composite Materials
ASTM D 7616/D7616M : 2011 : R2023 Standard Test Method for Determining Apparent Overlap Splice Shear Strength Properties of Wet Lay-Up Fiber-Reinforced Polymer Matrix Composites Used for Strengthening Civil Structures
ASTM D 2584 : 2011 Standard Test Method for Ignition Loss of Cured Reinforced Resins
ASTM D 4255/D4255M : 2020 : EDT 1 Standard Test Method for In-Plane Shear Properties of Polymer Matrix Composite Materials by the Rail Shear Method
ASTM D 3418 : 2015 Standard Test Method for Transition Temperatures and Enthalpies of Fusion and Crystallization of Polymers by Differential Scanning Calorimetry
ASTM D 3878 : 2016 Standard Terminology for Composite Materials
ASTM D 4473 : 2008 : R2021 Standard Test Method for Plastics: Dynamic Mechanical Properties: Cure Behavior
ASTM D 2344/D2344M : 2022 Standard Test Method for Short-Beam Strength of Polymer Matrix Composite Materials and Their Laminates
ASTM D 3530 : 1997 : R2015 Standard Test Method for Volatiles Content of Composite Material Prepreg
ASTM D 2990 : 2001 Standard Test Methods for Tensile, Compressive, and Flexural Creep and Creep-Rupture of Plastics
ASTM D 3518/D3518M : 1994 : EDT 1 Standard Test Method for In-Plane Shear Response of Polymer Matrix Composite Materials by Tensile Test of a &#177 45<sup>o</sup> Laminate
ASTM D 3410/D3410M : 2016 Standard Test Method for Compressive Properties of Polymer Matrix Composite Materials with Unsupported Gage Section by Shear Loading
ASTM D 3878 : 2019 : REV A Standard Terminology for Composite Materials
ASTM D 4018 : 1999 Standard Test Methods for Properties of Continuous Filament Carbon and Graphite Fiber Tows
ASTM D 3878 : 2020 : REV A Standard Terminology for Composite Materials
ASTM D 3878 : 1998 Standard Terminology Composite Materials
ASTM C 271/C271M : 2016 Standard Test Method for Density of Sandwich Core Materials
ASTM D 4065 : 2012 Standard Practice for Plastics: Dynamic Mechanical Properties: Determination and Report of Procedures
ASTM D 256 : 2023 Standard Test Methods for Determining the Izod Pendulum Impact Resistance of Plastics
ASTM D 3171 : 2022 Standard Test Methods for Constituent Content of Composite Materials
ASTM D 5528 : 2001 : R2007 Standard Test Method for Mode I Interlaminar Fracture Toughness of Unidirectional Fiber-Reinforced Polymer Matrix Composites
ASTM D 6416/D6416M : 2016 : EDT 1 Standard Test Method for Two-Dimensional Flexural Properties of Simply Supported Sandwich Composite Plates Subjected to a Distributed Load
ASTM D 3410/D3410M : 2016 : EDT 1 Standard Test Method for Compressive Properties of Polymer Matrix Composite Materials with Unsupported Gage Section by Shear Loading
ASTM D 7615/D7615M : 2019 Standard Practice for Open-Hole Fatigue Response of Polymer Matrix Composite Laminates
ASTM D 3878 : 2018 Standard Terminology for Composite Materials
ASTM D 7078/D7078M : 2020 : EDT 1 Standard Test Method for Shear Properties of Composite Materials by V-Notched Rail Shear Method
ASTM D 6507 : 2011 Standard Practice for Fiber Reinforcement Orientation Codes for Composite Materials
ASTM D 6641/D6641M : 2016 : EDT 2 Standard Test Method for Compressive Properties of Polymer Matrix Composite Materials Using a Combined Loading Compression (CLC) Test Fixture
ASTM D 5379/D5379M : 2019 Standard Test Method for Shear Properties of Composite Materials by the V-Notched Beam Method
ASTM D 7914/D7914M : 2014 Standard Test Method for Strength of Fiber Reinforced Polymer (FRP) Bent Bars in Bend Locations
ASTM D 6671/D6671M : 2019 Standard Test Method for Mixed Mode I-Mode II Interlaminar Fracture Toughness of Unidirectional Fiber Reinforced Polymer Matrix Composites
ASTM D 1822 : 2013 Standard Test Method for Tensile-Impact Energy to Break Plastics and Electrical Insulating Materials
ASTM D 3171 : 2009 Standard Test Methods for Constituent Content of Composite Materials
ASTM D 3800 : 2022 Standard Test Method for Density of High-Modulus Fibers
ASTM D 1822 : 2006 Standard Test Method for Tensile-Impact Energy to Break Plastics and Electrical Insulating Materials
ASTM D 6873/D6873M : 2019 Standard Practice for Bearing Fatigue Response of Polymer Matrix Composite Laminates
ASTM D 4018 : 2023 Standard Test Methods for Properties of Continuous Filament Carbon and Graphite Fiber Tows
ASTM D 7137/D7137M : 2017 Standard Test Method for Compressive Residual Strength Properties of Damaged Polymer Matrix Composite Plates
ASTM E 1461 : 1992 Standard Test Method for Thermal Diffusivity of Solids by the Flash Method
ASTM D 3878 : 2002 Standard Terminology for Composite Materials
ASTM D 638 : 2014 Standard Test Method for Tensile Properties of Plastics
ASTM D 2990 : 2009 Standard Test Methods for Tensile, Compressive, and Flexural Creep and Creep-Rupture of Plastics
ASTM D 7615/D7615M : 2023 Standard Practice for Open-Hole Fatigue Response of Polymer Matrix Composite Laminates
ASTM D 4255/D4255M : 2020 Standard Test Method for In-Plane Shear Properties of Polymer Matrix Composite Materials by the Rail Shear Method
ASTM D 7205/D7205M : 2006 : R2016 Standard Test Method for Tensile Properties of Fiber Reinforced Polymer Matrix Composite Bars
ASTM D 5766/D5766M : 2011 : R2018 Standard Test Method for Open-Hole Tensile Strength of Polymer Matrix Composite Laminates
ASTM D 6272 : 2017 Standard Test Method for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials by Four-Point Bending
ASTM D 5528 : 2013 Standard Test Method for Mode I Interlaminar Fracture Toughness of Unidirectional Fiber-Reinforced Polymer Matrix Composites
ASTM D 6484/D6484M : 2020 Standard Test Method for Open-Hole Compressive Strength of Polymer Matrix Composite Laminates
ASTM D 6507 : 2016 Standard Practice for Fiber Reinforcement Orientation Codes for Composite Materials
ASTM D 1822 : 1999 Standard Test Method for Tensile-Impact Energy to Break Plastics and Electrical Insulating Materials
ASTM D 3479/D3479M : 2019 : R2023 Standard Test Method for Tension-Tension Fatigue of Polymer Matrix Composite Materials
ASTM D 2990 : 1995 Standard Test Methods for Tensile, Compressive, and Flexural Creep and Creep-Rupture of Plastics
ASTM D 6115 : 1997 : R2004 Standard Test Method for Mode I Fatigue Delamination Growth Onset of Unidirectional Fiber-Reinforced Polymer Matrix Composites
ASTM D 3878 : 2020 : REV B Standard Terminology for Composite Materials
ASTM D 1505 : 1968 : R1979 Standard Test Method for Density Of Plastics By The Density-Gradient Technique
ASTM D 7332/D7332M : 2016 Standard Test Method for Measuring the Fastener Pull-Through Resistance of a <brk/>Fiber-Reinforced Polymer Matrix Composite
ASTM D 4473 : 1995 : REV A Standard Test Method for Plastics: Dynamic Mechanical Properties: Cure Behavior
ASTM D 7137/D7137M : 2023 Standard Test Method for Compressive Residual Strength Properties of Damaged Polymer Matrix Composite Plates
ASTM D 2584 : 1968 Standard Method Of Test For Ignition Loss Of Cured Reinforced Resins
ASTM D 7248/D7248M : 2021 Standard Test Method for High Bearing - Low Bypass Interaction Response of Polymer Matrix Composite Laminates Using 2-Fastener Specimens
ASTM D 6272 : 2002 Standard Test Method for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials by Four-Point Bending
ASTM D 6272 : 2002 : R2008 : EDT 1 Standard Test Method for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials by Four-Point Bending
ASTM D 5083 : 2017 Standard Test Method for Tensile Properties of Reinforced Thermosetting Plastics Using Straight-Sided Specimens
ASTM D 543 : 2020 Standard Practices for Evaluating the Resistance of Plastics to Chemical Reagents
ASTM D 7750 : 2012 : R2017 Standard Test Method for Cure Behavior of Thermosetting Resins by Dynamic Mechanical Procedures using an Encapsulated Specimen Rheometer
ASTM D 3878 : 2004 Standard Terminology for Composite Materials
ASTM D 7078/D7078M : 2020 Standard Test Method for Shear Properties of Composite Materials by V-Notched Rail Shear Method
ASTM D 3800 : 1999 Standard Test Method for Density of High-Modulus Fibers
ASTM D 618 : 2013 Standard Practice for Conditioning Plastics for Testing
ASTM D 5083 : 2008 Standard Test Method for Tensile Properties of Reinforced Thermosetting Plastics Using Straight-Sided Specimens
ASTM D 4018 : 1999 : R2004 Standard Test Methods for Properties of Continuous Filament Carbon and Graphite Fiber Tows
ASTM D 7291/D7291M : 2015 Standard Test Method for Through-Thickness “Flatwise” Tensile Strength and Elastic Modulus of a Fiber-Reinforced Polymer Matrix Composite Material
ASTM E 1269 : 2004 Standard Test Method for Determining Specific Heat Capacity by Differential Scanning Calorimetry
ASTM D 5961/D5961M : 2017 Standard Test Method for Bearing Response of Polymer Matrix Composite Laminates
ASTM D 2734 : 1994 Standard Test Methods for Void Content of Reinforced Plastics
ASTM D 4102 : 1982 : R2008 Standard Test Method for Thermal Oxidative Resistance of Carbon Fibers
ASTM D 3418 : 2008 Standard Test Method for Transition Temperatures and Enthalpies of Fusion and Crystallization of Polymers by Differential Scanning Calorimetry
ASTM D 6873/D6873M : 2023 Standard Practice for Bearing Fatigue Response of Polymer Matrix Composite Laminates
ASTM D 7264/D7264M : 2015 Standard Test Method for Flexural Properties of Polymer Matrix Composite Materials
ASTM E 1922 : 1997 Standard Test Method for Translaminar Fracture Toughness of Laminated Polymer Matrix Composite Materials
ASTM D 7336/D7336M : 2022 Standard Test Method for Static Energy Absorption Properties of Honeycomb Sandwich Core Materials
ASTM D 1822 : 2021 Standard Test Method for Determining the Tensile-Impact Resistance of Plastics
ASTM D 3878 : 2007 : R2013 Standard Terminology for Composite Materials
ASTM D 6856 : 2003 : R2008 Standard Guide for Testing Fabric-Reinforced "Textile" Composite Materials
ASTM C 365/C365M : 2016 Standard Test Method for Flatwise Compressive Properties of Sandwich Cores
ASTM D 1505 : 2010 Standard Test Method for Density of Plastics by the Density-Gradient Technique
ASTM D 6416/D6416M : 2016 Standard Test Method for Two-Dimensional Flexural Properties of Simply Supported Sandwich Composite Plates Subjected to a Distributed Load
ASTM D 3878 : 2020 : REDLINE Standard Terminology for Composite Materials
ASTM D 1505 : 2018 Standard Test Method for Density of Plastics by the Density-Gradient Technique
ASTM D 695 : 2015 Standard Test Method for Compressive Properties of Rigid Plastics
ASTM E 1269 : 2011 Standard Test Method for Determining Specific Heat Capacity by Differential Scanning Calorimetry
ASTM D 3878 : 2020 Standard Terminology for Composite Materials
ASTM D 2584 : 2018 Standard Test Method for Ignition Loss of Cured Reinforced Resins
ASTM D 3878 : 2003 Standard Terminology for Composite Materials
ASTM D 7522/D7522M : 2021 Standard Test Method for Pull-Off Strength for FRP Laminate Systems Bonded to Concrete or Masonry Substrates
ASTM D 6415/D6415M : 2006 : REV A : R2013 Standard Test Method for Measuring the Curved Beam Strength of a Fiber-Reinforced Polymer-Matrix Composite
ASTM D 7336/D7336M : 2016 Standard Test Method for Static Energy Absorption Properties of Honeycomb Sandwich Core Materials
ASTM D 6641/D6641M : 2016 : EDT 1 Standard Test Method for Compressive Properties of Polymer Matrix Composite Materials Using a Combined Loading Compression (CLC) Test Fixture
ASTM D 1505 : 1998 : EDT 1 Standard Test Method for Density of Plastics by the Density-Gradient Technique
ASTM E 1461 : 2013 : R2022 Standard Test Method for Thermal Diffusivity by the Flash Method
ASTM D 6772/D6772M : 2022 Standard Test Method for Dimensional Stability of Sandwich Core Materials
ASTM E 1461 : 2013 Standard Test Method for Thermal Diffusivity by the Flash Method
ASTM D 570 : 2022 Standard Test Method for Water Absorption of Plastics
ASTM E 1922 : 2004 : R2010 : EDT 1 Standard Test Method for Translaminar Fracture Toughness of Laminated and Pultruded Polymer Matrix Composite Materials
ASTM C 366/C366M : 2016 : R2022 : EDT 1 Standard Test Methods for Measurement of Thickness of Sandwich Cores
ASTM D 4065 : 1995 Standard Practice for Plastics: Dynamic Mechanical Properties: Determination and Report of Procedures
ASTM D 3479/D3479M : 2019 Standard Test Method for Tension-Tension Fatigue of Polymer Matrix Composite Materials
ASTM D 3878 : 2007 Standard Terminology for Composite Materials
ASTM D 6264/D6264M : 2023 Standard Test Method for Measuring the Damage Resistance of a Fiber-Reinforced Polymer-Matrix Composite to a Concentrated Quasi-Static Indentation Force
ASTM E 1461 : 2001 Standard Test Method for Thermal Diffusivity of Solids by the Flash Method
ASTM D 6507 : 2000 : R2005 Standard Practice for Fiber Reinforcement Orientation Codes for Composite Materials
ASTM D 5450/D5450M : 2016 Standard Test Method for Transverse Tensile Properties of Hoop Wound Polymer Matrix Composite Cylinders
ASTM D 3800 : 2016 Standard Test Method for Density of High-Modulus Fibers
ASTM D 4102 : 1982 : R1999 Standard Test Method for Thermal Oxidative Resistance of Carbon Fibers
ASTM C 365/C365M : 2022 Standard Test Method for Flatwise Compressive Properties of Sandwich Cores
ASTM D 2734 : 2009 Standard Test Methods for Void Content of Reinforced Plastics
ASTM D 6507 : 2000 Standard Practice for Fiber Reinforcement Orientation Codes for Composite Materials
ASTM D 4102 : 1982 : R2015 Standard Test Method for Thermal Oxidative Resistance of Carbon Fibers
ASTM D 7028 : 2007 : EDT 1 Standard Test Method for Glass Transition Temperature (DMA Tg) of Polymer Matrix Composites by Dynamic Mechanical Analysis (DMA)
ASTM D 3171 : 1999 : R2004 Standard Test Methods for Constituent Content of Composite Materials
ASTM D 4473 : 2001 Standard Test Method for Plastics: Dynamic Mechanical Properties: Cure Behavior
ASTM D 7914/D7914M : 2021 Standard Test Method for Strength of Fiber Reinforced Polymer (FRP) Bent Bars in Bend Locations
ASTM D 7766/D7766M : 2023 Standard Practice for Damage Resistance Testing of Sandwich Constructions
ASTM D 695 : 2023 Standard Test Method for Compressive Properties of Rigid Plastics
ASTM E 1269 : 2011 : R2018 Standard Test Method for Determining Specific Heat Capacity by Differential Scanning Calorimetry
ASTM D 570 : 1998 : R2018 Standard Test Method for Water Absorption of Plastics
ASTM D 3171 : 2015 Standard Test Methods for Constituent Content of Composite Materials
ASTM D 4473 : 2008 Standard Test Method for Plastics: Dynamic Mechanical Properties: Cure Behavior
ASTM D 5448/D5448M : 2016 Standard Test Method for Inplane Shear Properties of Hoop Wound Polymer Matrix Composite Cylinders
ASTM D 6415/D6415M : 2022 Standard Test Method for Measuring the Curved Beam Strength of a Fiber-Reinforced Polymer-Matrix Composite
ASTM D 6272 : 2000 Standard Test Method for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials by Four-Point Bending
ASTM D 3878 : 2004 : REV A Standard Terminology for Composite Materials
ASTM D 6671/D6671M : 2022 Standard Test Method for Mixed Mode I-Mode II Interlaminar Fracture Toughness of Unidirectional Fiber Reinforced Polymer Matrix Composites
ASTM D 3171 : 2006 Standard Test Methods for Constituent Content of Composite Materials
ASTM D 5528 : 2001 : R2007 : EDT 2 Standard Test Method for Mode I Interlaminar Fracture Toughness of Unidirectional Fiber-Reinforced Polymer Matrix Composites
ASTM D 4018 : 1999 : R2008 Standard Test Methods for Properties of Continuous Filament Carbon and Graphite Fiber Tows
ASTM D 7616/D7616M : 2011 : R2017 Standard Test Method for Determining Apparent Overlap Splice Shear Strength Properties of Wet Lay-Up Fiber-Reinforced Polymer Matrix Composites Used for Strengthening Civil Structures
ASTM D 2583 : 2007 Standard Test Method for Indentation Hardness of Rigid Plastics by Means of a Barcol Impressor
ASTM D 4102 : 1982 : R2004 Standard Test Method for Thermal Oxidative Resistance of Carbon Fibers
ASTM D 7028 : 2007 : R2015 Standard Test Method for Glass Transition Temperature (DMA Tg) of Polymer Matrix Composites by Dynamic Mechanical Analysis (DMA)
ASTM E 228 : 2022 Standard Test Method for Linear Thermal Expansion of Solid Materials With a Push-Rod Dilatometer
ASTM D 618 : 2021 Standard Practice for Conditioning Plastics for Testing
ASTM D 2583 : 1995 Standard Test Method for Indentation Hardness of Rigid Plastics by Means of a Barcol Impressor
ASTM D 7522/D7522M : 2015 Standard Test Method for Pull-Off Strength for FRP Laminate Systems Bonded to Concrete Substrate
ASTM D 3878 : 2001 Standard Terminology Composite Materials
ASTM D 3846 : 2008 : R2015 Standard Test Method for In-Plane Shear Strength of Reinforced Plastics (Withdrawn 2024)
ASTM C 366/C366M : 2016 Standard Test Methods for Measurement of Thickness of Sandwich Cores
ASTM D 638 : 2022 Standard Test Method for Tensile Properties of Plastics
ASTM D 7957/D7957M : 2022 Standard Specification for Solid Round Glass Fiber Reinforced Polymer Bars for Concrete Reinforcement
ASTM E 1922 : 2004 Standard Test Method for Translaminar Fracture Toughness of Laminated and Pultruded Polymer Matrix Composite Materials
ASTM D 4065 : 2001 Standard Practice for Plastics: Dynamic Mechanical Properties: Determination and Report of Procedures

View more information
US$108.00
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.