DEFSTAN 02-329/3(2010) : 2010
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
REQUIREMENTS FOR HEAT EXCHANGERS FOR HM SURFACE SHIPS AND SUBMARINES
Hardcopy , PDF
07-08-2015
English
01-01-2010
Foreword
1 Scope
2 Warning
3 Normative References
4 Definitions
5 Abbreviations
6 Performance Specification
7 National/International Regulations
8 Requirements
9 Design Requirements/Guidance
10 Corporate Experience & Knowledge
Describes the general requirements for heat exchangers installed in HM Surface Ships and Submarines.
DevelopmentNote |
Supersedes DEFSTAN 02-329/2(2005). (04/2010)
|
DocumentType |
Standard
|
Pages |
28
|
PublisherName |
UK Ministry of Defence Standards
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
DEFSTAN 02-878/1(2011) : 2011 | NON-FERROUS TUBES AND PIPES FOR USE IN HM SUBMARINES AND SURFACE SHIPS NOT IN CLASS |
DEFSTAN 02-728/3(2010) : 2010 | REQUIREMENTS FOR DOMESTIC HOT AND COLD FRESH WATER SYSTEMS |
DEFSTAN 02-303/3(2015) : 2015 | LUBRICATING OIL SYSTEMS FOR PROPULSION AND GENERATION IN HM SURFACE SHIPS & SUBMARINES |
BS EN 1653:1998 | Copper and copper alloys. Plate, sheet and circles for boilers, pressure vessels and hot water storage units |
DEFSTAN 02-830(PT1)/2(2002) : 2002 AMD 1 2003 | REQUIREMENTS FOR GUNMETAL INGOTS AND CASTINGS - PART 1: GUNMETAL INGOTS AND CLASS 3 GUNMETAL SAND CASTINGS |
DEFSTAN 02-747(PT2)/2(2004) : 2004 | REQUIREMENTS FOR NICKEL ALUMINIUM BRONZE CASTINGS AND INGOTS - PART 2: NICKEL ALUMINIUM BRONZE NAVAL ALLOY INGOTS AND SAND CASTINGS WITH WELDING PERMITTED TO THE WETTED SURFACE |
DEFSTAN 02-780(PT2)/2(2009) : 2009 | REQUIREMENTS FOR 70/30 COPPER NICKEL ALLOY MATERIAL - PART 2: FORGINGS, FORGE STOCK RODS AND SECTIONS |
DEFSTAN 02-374/2(2009) : 2009 | RUBBER FLEXIBLE PIPES AND BELLOWS FOR USE IN SUBMARINES |
BS EN 10222-4:2017 | Steel forgings for pressure purposes Weldable fine grain steels with high proof strength |
BS EN 10028-5:2017 | Flat products made of steels for pressure purposes Weldable fine grain steels, thermomechanically rolled |
BS EN 10217-4:2002 | Welded steel tubes for pressure purposes. Technical delivery conditions Electric welded non-alloy steel tubes with specified low temperature properties |
BS EN 10028-7:2007 | Flat products made of steels for pressure purposes Stainless steels |
BS EN 1676:2010 | Aluminium and aluminium alloys. Alloyed ingots for remelting. Specifications |
BS EN 10222-1:2017 | Steel forgings for pressure purposes General requirements for open die forgings |
ASTM B 338 : 2017 : REDLINE | Standard Specification for Seamless and Welded Titanium and Titanium Alloy Tubes for Condensers and Heat Exchangers |
BS MA 18:1973 | Specification for salt water piping systems in ships |
ASTM B 265 : 2015 : REDLINE | Standard Specification for Titanium and Titanium Alloy Strip, Sheet, and Plate |
DEFSTAN 08-123/1(2000) : 2000 | REQUIREMENTS FOR THE DESIGN AND TESTING OF EQUIPMENTS TO MEET ENVIRONMENTAL CONDITIONS - CATEGORY 2 |
BS EN 10048:1997 | Hot rolled narrow steel strip. Tolerances on dimensions and shape |
DEFSTAN 02-833(PT1)/2(2007) : 2007 | REQUIREMENTS FOR NICKEL ALUMINIUM BRONZE - PART 1: SHEET, STRIP AND PLATE |
DEFSTAN 02-747(PT1)/2(2007) : 2007 | REQUIREMENTS FOR NICKEL ALUMINIUM BRONZE CASTINGS AND INGOTS - PART 1: NICKEL ALUMINIUM BRONZE NAVAL ALLOY CENTRIFUGALLY CAST |
DEFSTAN 02-341(PT1)/1(2000) : 2000 | REQUIREMENTS FOR CLEANING OF ITEMS, COMPONENTS AND EQUIPMENT FOR FLUID SYSTEMS - PART 1: CLEANING CATEGORY 2 |
DEFSTAN 02-862(PT2)/2(2007) : 2007 | FASTENERS - PART 2: FERROUS |
BS EN 10222-5:2017 | Steel forgings for pressure purposes Martensitic, austenitic and austenitic-ferritic stainless steels |
BS EN 10085:2001 | Nitriding steel. Technical delivery conditions |
BS EN 10028-6:2017 | Flat products made of steels for pressure purposes Weldable fine grain steels, quenched and tempered |
DEFSTAN 02-723/1(2000) : 2000 | REQUIREMENTS FOR MARKER PLATES |
BS EN 10217-2 : 2002 | WELDED STEEL TUBES FOR PRESSURE PURPOSES - TECHNICAL DELIVERY CONDITIONS - PART 2: ELECTRIC WELDED NON-ALLOY AND ALLOY STEEL TUBES WITH SPECIFIED ELEVATED TEMPERATURE PROPERTIES |
DEFSTAN 08-120/1(2000) : 2000 | REQUIREMENTS FOR DETERMINING THE SHOCK STRENGTH OF EQUIPMENT - CATEGORY 2 |
BS EN 10095:1999 | Heat resisting steels and nickel alloys |
DEFSTAN 02-747(PT3)/1(2000) : 2000 | REQUIREMENTS FOR NICKEL ALUMINIUM BRONZE CASTINGS AND INGOTS - PART 3: NICKEL ALUMINIUM BRONZE COMMERCIAL ALLOY INGOTS AND SAND CASTINGS |
DEFSTAN 08-118(PT1)/1(2000) : 2000 | DESIGN GUIDE ON THE REDUCTION OF ACOUSTIC NOISE IN SURFACE SHIPS - CATEGORY 3 - PART 1: REDUCTION OF NOISE RADIATED UNDERWATER |
BS EN 1057 : 2006 | COPPER AND COPPER ALLOYS - SEAMLESS, ROUND COPPER TUBES FOR WATER AND GAS IN SANITARY AND HEATING APPLICATIONS |
BS EN ISO 9445:2006 | Continuously cold-rolled stainless steel narrow strip, wide strip, plate/sheet and cut lengths. Tolerances on dimensions and form |
BS EN 10250-4:2000 | Open steel die forgings for general engineering purposes Stainless steels |
BS EN 10051:2010 | Continuously hot-rolled strip and plate/sheet cut from wide strip of non-alloy and alloy steels. Tolerances on dimensions and shape |
BS EN 10217-6:2002 | Welded steel tubes for pressure purposes. Technical delivery conditions Submerged arc welded non-alloy steel tubes with specified low temperature properties |
DEFSTAN 02-745/1(2006) : 2006 | CLASSIFICATION, INSPECTION REQUIREMENTS AND ACCEPTANCE STANDARDS FOR STEEL CASTINGS |
BS EN 10028-1:2017 | Flat products made of steels for pressure purposes General requirements |
DEFSTAN 02-863/1(2000) : 2000 | REQUIREMENTS FOR THE CLASSIFICATION, DIMENSIONS, TOLERANCES AND GENERAL STANDARDS OF ACCEPTANCE FOR COPPER AND NICKEL ALLOY CASTINGS |
DEFSTAN 02-387/2(2001) : 2001 | REQUIREMENTS FOR CHEMICAL CLEANING OF CHILLED WATER SYSTEMS FOR HM SURFACE SHIPS, SUBMARINES AND ROYAL FLEET AUXILIARY VESSELS |
BS EN 10028-3:2017 | Flat products made of steels for pressure purposes Weldable fine grain steels, normalized |
DEFSTAN 05-10(PT2)/5(2006) : 2006 | PRODUCT DEFINITION INFORMATION - PART 2: DIGITAL PRODUCT DEFINITION INFORMATION |
DEFSTAN 02-779(PT3)/1(2000) : 2000 | REQUIREMENTS FOR 90/10 COPPER NICKEL ALLOY MATERIAL - PART 3: TUBES CATEGORY 2 |
DEFSTAN 05-10(PT1)/5(2006) : 2006 | PRODUCT DEFINITION INFORMATION - PART 1: HARDCOPY/MICROFORM PRODUCT DEFINITION INFORMATION |
DEFSTAN 02-833(PT2)/2(2007) : 2007 | REQUIREMENTS FOR NICKEL ALUMINIUM BRONZE - PART 2: FORGINGS, FORGING STOCK, RODS AND SECTIONS |
BS EN 1654:1998 | Copper and copper alloys. Strip for springs and connectors |
BS EN 10216-3:2013 | Seamless steel tubes for pressure purposes. Technical delivery conditions Alloy fine grain steel tubes |
BS EN 1652:1998 | Copper and copper alloys. Plate, sheet, strip and circles for general purposes |
BS EN 10087:1999 | Free cutting steels. Technical delivery conditions for semi-finished products, hot rolled bars and rods |
BS EN 1559-4:2015 | Founding. Technical conditions of delivery Additional requirements for aluminium alloy castings |
BS EN 10084:2008 | Case hardening steels. Technical delivery conditions |
DEFSTAN 02-862(PT1)/2(2007) : 2007 | FASTENERS - PART 1: GENERAL |
DEFSTAN 02-837/2(2005) : 2005 | REQUIREMENTS FOR COPPER TUBES |
DEFSTAN 05-10(PT0)/5(2006) : 2006 | PRODUCT DEFINITION INFORMATION - PART 0: GENERAL INTRODUCTION TO PRODUCT DEFINITION INFORMATION |
DEFSTAN 02-703/1(2000) : 2000 | THERMAL AND ACOUSTIC INSULATION OF HULL AND MACHINERY |
DEFSTAN 02-330/2(2007) : 2007 | REQUIREMENTS FOR MAIN PROPULSION PLANT CONDENSERS IN NUCLEAR POWERED SUBMARINES |
BS EN 10028-2:2017 | Flat products made of steels for pressure purposes Non-alloy and alloy steels with specified elevated temperature properties |
BS EN 10029:2010 | Hot-rolled steel plates 3 mm thick or above. Tolerances on dimensions and shape |
BS EN 10217-5:2002 | Welded steel tubes for pressure purposes. Technical delivery conditions Submerged arc welded non-alloy and alloy steel tubes with specified elevated temperature properties |
BS EN 10028-4:2017 | Flat products made of steels for pressure purposes Nickel alloy steels with specified low temperature properties |
DEFSTAN 02-345/1(2000) : 2000 AMD 1 2002 | REQUIREMENTS FOR FLEXIBLE RUBBER PIPE ASSEMBLIES AND BELLOWS FOR USE IN SYSTEMS FROM VACUUM TO 10 BAR |
BS EN 12449:2016 | Copper and copper alloys. Seamless, round tubes for general purposes |
DEFSTAN 02-830(PT2)/2(2002) : 2002 | REQUIREMENTS FOR GUNMETAL INGOTS AND CASTINGS - PART 2: CONTINUOUSLY CAST |
BS EN 10217-3:2002 | Welded steel tubes for pressure purposes. Technical delivery conditions Alloy fine grain steel tubes |
DEFSTAN 05-10(PT3)/5(2006) : 2006 | PRODUCT DEFINITION INFORMATION - PART 3: PRODUCT DEFINITION INFORMATION GUIDANCE |
BS EN 1706:2010 | Aluminium and aluminium alloys. Castings. Chemical composition and mechanical properties |
DEFSTAN 02-780(PT3)/1(2000) : 2000 | REQUIREMENTS FOR 70/30 COPPER NICKEL ALLOY MATERIAL - PART 3: TUBES CATEGORY 2 |
BS EN 12451:2012 | Copper and copper alloys. Seamless, round tubes for heat exchangers |
BS EN 10216-1:2013 | Seamless steel tubes for pressure purposes. Technical delivery conditions Non-alloy steel tubes with specified room temperature properties |
DEFSTAN 08-162/1(2003) : 2003 | LUBRICATING OIL SYSTEMS FOR PROPULSION AND GENERATION IN HM SURFACE SHIPS AND SUBMARINES - CATEGORY 2 |
BS EN 10269:2013 | Steels and nickel alloys for fasteners with specified elevated and/or low temperature properties |
BS EN 10222-2:2017 | Steel forgings for pressure purposes Ferritic and martensitic steels with specified elevated temperatures properties |
BS EN 10217-1:2002 | Welded steel tubes for pressure purposes. Technical delivery conditions Non-alloy steel tubes with specified room temperature properties |
DEFSTAN 01-5/16(2009) : 2009 | FUELS, LUBRICANTS AND ASSOCIATED PRODUCTS |
BS 3076:1989 | Specification for nickel and nickel alloys: bar |
BS EN 10216-4:2013 | Seamless steel tubes for pressure purposes. Technical delivery conditions Non-alloy and alloy steel tubes with specified low temperature properties |
DEFSTAN 02-743(PT1)/1(2000) : 2000 | PIPE MANIPULATION - PART 1: BENDING OF PIPES CATEGORY 2 |
BS EN 10216-2:2013 | Seamless steel tubes for pressure purposes. Technical delivery conditions Non-alloy and alloy steel tubes with specified elevated temperature properties |
BS EN 10083-1:2006 | Steels for quenching and tempering General technical delivery conditions |
DEFSTAN 02-360/2(2001) : 2001 | GUIDANCE TO THE SELECTION OF LOW PRESSURE METRIC STANDARD VALVES |
DEFSTAN 02-102(PT1)/3(2005) : 2005 | REQUIREMENTS FOR AIR-CONDITIONING AND VENTILATION - PART 1: HM SURFACE SHIPS AND ROYAL FLEET AUXILIARIES |
BS EN 1559-1:2011 | Founding. Technical conditions of delivery General |
DEFSTAN 02-375/1(2000) : 2000 | VALVE DESIGN AND MANUFACTURE CATEGORY 2 |
DEFSTAN 07-253(PT1)/1(2000) : 2000 | REQUIREMENTS FOR 70/30 COPPER NICKEL ALLOY - CATEGORY 2 - PART 1: SHEET, STRIP, PLATE |
BS EN 10222-3:2017 | Steel forgings for pressure purposes Nickel steels with specified low temperature properties |
DEFSTAN 02-747(PT4)/2(2005) : 2005 | REQUIREMENTS FOR NICKEL ALUMINIUM BRONZE CASTINGS AND INGOTS - PART 4: NICKEL ALUMINIUM BRONZE NAVAL ALLOY SAND CASTINGS WITH WELDING RESTRICTED TO THE NON-WETTED SURFACE (CLASS 1 AND 2 CASTINGS ONLY) |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.