Connections for hydraulic fluid power and general use. Hose fittings Hose fittings with ISO 6149 metric stud ends

Available format(s)

Hardcopy , PDF

Language(s)

English

Published date

08-31-2007

Publisher

British Standards Institution

Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Performance requirements
5 Designation of hose fittings
6 Design
7 Manufacture
8 Procurement information
9 Marking
10 Assembly
11 Identification statement (reference to this part of
   ISO 12151)
Annex A (informative) Instructions for assembling hose
                      fittings in ISO 6149-1 straight
                      thread O-ring port
Bibliography

Defines the general and dimensional requirements for the design and performance of ISO 6149 metric stud-end hose fittings made of carbon steel, for nominal hose inside diameters of 6,3 mm through 38 mm inclusive, in accordance with ISO 4397.

This part of ISO12151 specifies the general and dimensional requirements for the design and performance of ISO6149 metric stud-end hose fittings made of carbon steel, for nominal hose inside diameters of 6,3mm through 38mm inclusive, in accordance with ISO4397.

NOTE1 Other materials can be supplied as agreed between the manufacturer and user.

NOTE2 Method of attachment of fitting to hose is optional, for example, permanent, field-attachable, push-on, beaded, etc. Also included is a 90° elbow hose fitting suitable for hose connections made with or without hose clamps in relatively low-pressure applications.

NOTE3 See ISO4038 and ISO4039 for hose fittings used in hydraulic and pneumatic braking systems on road vehicles (as defined in the scope of ISO/TC22).

These hose fittings (see Figure1 for a typical example) are for use in hydraulic fluid power systems with hose that meets the requirements of the respective hose standards and in general applications with suitable hoses.

Committee	MCE/18/-/4
DocumentType	Standard
Pages	18
PublisherName	British Standards Institution
Status	Current

Standards	Relationship
ISO 12151-4:2007	Identical

ISO 4079-1:2001	Rubber hoses and hose assemblies Textile-reinforced hydraulic types Specification Part 1: Oil-based fluid applications
ISO 4039-1:1998	Road vehicles — Pneumatic braking systems — Part 1: Pipes, male fittings and tapped holes with facial sealing surface
ISO 3949:2009	Plastics hoses and hose assemblies Textile-reinforced types for hydraulic applications Specification
ISO 5598:2008	Fluid power systems and components Vocabulary
ISO 4759-1:2000	Tolerances for fasteners — Part 1: Bolts, screws, studs and nuts — Product grades A, B and C
ISO 6605:2017	Hydraulic fluid power — Test methods for hoses and hose assemblies
ISO 4397:2011	Fluid power connectors and associated components — Nominal outside diameters of tubes and nominal hose sizes
ISO 4039-2:1998	Road vehicles Pneumatic braking systems Part 2: Pipes, male fittings and holes with conical sealing surface
ISO 6149-3:2006	Connections for hydraulic fluid power and general use Ports and stud ends with ISO 261 metric threads and O-ring sealing Part 3: Dimensions, design, test methods and requirements for light-duty (L series) stud ends
ISO 4038:1996	Road vehicles — Hydraulic braking systems — Simple flare pipes, tapped holes, male fittings and hose end fittings
ISO 1436-1:2001	Rubber hoses and hose assemblies Wire-braid-reinforced hydraulic types Specification Part 1: Oil-based fluid applications
ISO 19879:2010	Metallic tube connections for fluid power and general use Test methods for hydraulic fluid power connections
ISO 6149-2:2006	Connections for hydraulic fluid power and general use Ports and stud ends with ISO 261 metric threads and O-ring sealing Part 2: Dimensions, design, test methods and requirements for heavy-duty (S series) stud ends
ISO 6149-1:2006	Connections for hydraulic fluid power and general use Ports and stud ends with ISO 261 metric threads and O-ring sealing Part 1: Ports with truncated housing for O-ring seal
ISO 9227:2017	Corrosion tests in artificial atmospheres — Salt spray tests
ISO 261:1998	ISO general purpose metric screw threads General plan
ISO 3862-1:2001	Rubber hoses and hose assemblies Rubber-covered spiral-wire-reinforced hydraulic types Specification Part 1: Oil-based fluid applications
ISO 11237-1:2004	Rubber hoses and hose assemblies Wire-braid-reinforced compact types for hydraulic applications Specification Part 1: Oil-based fluid applications

View more information

US$170.10

Excluding Tax where applicable

Product format

I agree to the DRM document license rules apply against the PDF selection made.

Please confirm that you agree to the document license rules for this document.

I agree to the document license rules .

Please confirm that you agree to the document license rules for this document.

Access your standards online with a subscription

Features

Simple online access to standards, technical information and regulations.
Critical updates of standards and customisable alerts and notifications.
Multi-user online standards collection: secure, flexible and cost effective.

Learn more on subscription solutions

Get in touch with us

BS ISO 12151-4:2007

Connections for hydraulic fluid power and general use. Hose fittings Hose fittings with ISO 6149 metric stud ends

Table of Contents

Abstract

Scope

General Product Information

International Equivalents

Standards Referencing This Book

Category

Subcategory