• There are no items in your cart

ASTM D 7891 : 2015

Current
Current

The latest, up-to-date edition.

Standard Test Method for Shear Testing of Powders Using the Freeman Technology FT4 Powder Rheometer Shear Cell
Available format(s)

Hardcopy , PDF

Language(s)

English

Published date

03-01-2015

CONTAINED IN VOL. 04.09, 2015 Defines the apparatus and procedures for measuring the incipient failure properties of a powder as a function of the normal stress for a given level of consolidation.

1.1This method covers the apparatus and procedures for measuring the incipient failure properties of a powder as a function of the normal stress for a given level of consolidation. The method also allows the further determination of the unconfined yield strength, internal friction angles, cohesion, flow function, major principal stress and wall friction angle (with the appropriate wall coupon fitted to the correct accessory).

1.2These parameters are most commonly used for the design of storage hoppers and bins using industry standard calculations and procedures. They can also provide relative classification or comparison of the flow behavior of different powders or different batches of the same powder if similar stress and shear regimes are encountered within the processing equipment.

1.3The apparatus is suitable for measuring the properties of powders with a maximum particle size of 1 mm. It is possible to test powders which have a small proportion of particles of 1 mm or greater, but they should be present in the bulk sample as no more than 5 % of the total mass in samples with a normal (Gaussian) size distribution.

1.4All observed and calculated values shall conform to the guidelines for significant digits and rounding established in Practice D6026.

1.4.1The procedures used to specify how data are collected/recorded or calculated, in this standard are regarded as the industry standard. In addition, they are representative of the significant digits that generally should be retained. The procedures used do not consider material variation, purpose for obtaining the data, special purpose studies, or any considerations for the user’s objectives; and it is common practice to increase or reduce significant digits of reported data to be commensurate with these considerations. It is beyond the scope of this standard to consider significant digits used in analysis methods for engineering design.

1.5Units—The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

1.6This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Committee
D 18
DocumentType
Test Method
Pages
11
PublisherName
American Society for Testing and Materials
Status
Current

ASTM D 8081 : 2017 Standard Guide for Theory and Principles for Obtaining Reliable and Accurate Bulk Solids Flow Data Using a Direct Shear Cell

ASTM D 2216 : 2005 Standard Test Methods for Laboratory Determination of Water (Moisture) Content of Soil and Rock by Mass
ASTM D 6128 : 1997 Standard Test Method for Shear Testing of Bulk Solids Using the Jenike Shear Cell
ASTM D 6128 : 2022 Standard Test Method for Shear Testing of Bulk Solids Using the Jenike Shear Tester
ASTM D 653 : 2007 Standard Terminology Relating to Soil, Rock, and Contained Fluids
ASTM D 2216 : 2010 Standard Test Methods for Laboratory Determination of Water (Moisture) Content of Soil and Rock by Mass
ASTM D 3740 : 2012 Standard Practice for Minimum Requirements for Agencies Engaged in Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction
ASTM D 6773 : 2016 : REDLINE Standard Test Method for Bulk Solids Using Schulze Ring Shear Tester
ASTM D 3740 : 2023 Standard Practice for Minimum Requirements for Agencies Engaged in Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction
ASTM D 6128 : 2006 Standard Test Method for Shear Testing of Bulk Solids Using the Jenike Shear Cell
ASTM D 3740 : 2019 Standard Practice for Minimum Requirements for Agencies Engaged in Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction
ASTM D 3740 : 2004 : REV A : EDT 1 Standard Practice for Minimum Requirements for Agencies Engaged in the Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction
ASTM D 6128 : 2014 Standard Test Method for Shear Testing of Bulk Solids Using the Jenike Shear Cell
ASTM D 6773 : 2002 Standard Shear Test Method for Bulk Solids Using the Schulze Ring Shear Tester
ASTM D 3740 : 2008 Standard Practice for Minimum Requirements for Agencies Engaged in Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction
ASTM D 6026 : 2013 Standard Practice for Using Significant Digits in Geotechnical Data
ASTM D 6682 : 2001 Standard Test Method for Measuring the Shear Stresses of Powders Using the Peschl Rotational Split Level Shear Tester
ASTM D 3740 : 2012-06 PRACTICE FOR MINIMUM REQUIREMENTS FOR AGENCIES ENGAGED IN TESTING AND/OR INSPECTION OF SOIL AND ROCK AS USED IN ENGINEERING DESIGN AND CONSTRUCTION
ASTM D 6026 : 2006 Standard Practice for Using Significant Digits in Geotechnical Data
ASTM D 3740 : 1999 : REV C Standard Practice for Minimum Requirements for Agencies Engaged in the Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction
ASTM D 6128 : 2016 : REDLINE Standard Test Method for Shear Testing of Bulk Solids Using the Jenike Shear Tester
ASTM D 653 : 2022 Standard Terminology Relating to Soil, Rock, and Contained Fluids
ASTM D 6128 : 2000 Standard Test Method for Shear Testing of Bulk Solids Using the Jenike Shear Cell
ASTM D 6773 : 2008 Standard Shear Test Method for Bulk Solids Using the Schulze Ring Shear Tester
ASTM D 653 : 2020 : EDT 1 Standard Terminology Relating to Soil, Rock, and Contained Fluids
ASTM D 6026 : 1999 Standard Practice for Using Significant Digits in Geotechnical Data
ASTM D 3740 : 2011 Standard Practice for Minimum Requirements for Agencies Engaged in Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction
ASTM D 6773 : 2016 Standard Test Method for Bulk Solids Using Schulze Ring Shear Tester
ASTM D 6026 : 2001 : EDT 1 Standard Practice for Using Significant Digits in Geotechnical Data
ASTM D 3740 : 2010 Standard Practice for Minimum Requirements for Agencies Engaged in Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction
ASTM D 653 : 2021 : REV A Standard Terminology Relating to Soil, Rock, and Contained Fluids
ASTM D 2216 : 2019 Standard Test Methods for Laboratory Determination of Water (Moisture) Content of Soil and Rock by Mass
ASTM D 6026 : 1996 Standard Practice for Using Significant Digits in Geotechnical Data
ASTM D 3740 : 2004 : REV A Standard Practice for Minimum Requirements for Agencies Engaged in the Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction
ASTM D 3740 : 2001 Standard Practice for Minimum Requirements for Agencies Engaged in the Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction
ASTM D 653 : 2021 Standard Terminology Relating to Soil, Rock, and Contained Fluids
ASTM D 653 : 2021 : REV B Standard Terminology Relating to Soil, Rock, and Contained Fluids
ASTM D 6682 : 2008 Standard Test Method for Measuring Shear Stresses of Powders Using Peschl Rotational Split Level Shear Tester (Withdrawn 2017)
ASTM D 6773 : 2022 Standard Test Method for Bulk Solids Using Schulze Ring Shear Tester
ASTM D 6682 : 2001 : R2006 Standard Test Method for Measuring Shear Stresses of Powders Using Peschl Rotational Split Level Shear Tester
ASTM D 6026 : 1996 : EDT 1 Standard Practice for Using Significant Digits in Geotechnical Data
ASTM D 3740 : 2012 : REV A Standard Practice for Minimum Requirements for Agencies Engaged in Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction
ASTM D 3740 : 2003 Standard Practice for Minimum Requirements for Agencies Engaged in the Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction
ASTM D 2216 : 1998 Standard Test Method for Laboratory Determination of Water (Moisture) Content of Soil and Rock by Mass
ASTM D 6026 : 2021 Standard Practice for Using Significant Digits and Data Records in Geotechnical Data
ASTM D 2216 : 1971 Standard Method of Laboratory Determination Of Moisture Content Of Soil
ASTM D 6026 : 2001 Standard Practice for Using Significant Digits in Geotechnical Data
ASTM D 6128 : 2016 Standard Test Method for Shear Testing of Bulk Solids Using the Jenike Shear Tester
ASTM D 6026 : 2013 : REDLINE Standard Practice for Using Significant Digits in Geotechnical Data
ASTM D 3740 : 2004 Standard Practice for Minimum Requirements for Agencies Engaged in the Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction
ASTM D 653 : 2014 : REDLINE Standard Terminology Relating to Soil, Rock, and Contained Fluids

View more information
US$69.00
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.