Skip to content
Please enter a keyword to search

  • SAE AMS 1424 : 2017

    View superseded by
    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    Add to Watchlist
    View superseded by
    This Standard has been added successfully to your Watchlist.
    Please visit My Watchlist to see all standards that you are watching.
    Please log in or to add this standard to your Watchlist.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    You have already added this standard to your Watchlist.
    Visit My Watchlist to view the full list.

    FLUID, AIRCRAFT DEICING/ANTI-ICING, SAE TYPE 1

    Available format(s):  Hardcopy, PDF

    Superseded date:  10-06-2018

    Language(s):  English

    Published date:  01-01-2017

    Publisher:  SAE International

    Add to Watchlist

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    1. SCOPE
    2. APPLICABLE DOCUMENTS
    3. TECHNICAL REQUIREMENTS
    4. QUALITY ASSURANCE PROVISIONS
    5. PREPARATION FOR DELIVERY
    6. ACKNOWLEDGMENT
    7. REJECTIONS
    8. NOTES
    APPENDIX A - ENVIRONMENTAL REQUIREMENTS AND TEST METHODS

    Abstract - (Show below) - (Hide below)

    Describes a deicing/anti-icing material in the form of a fluid.

    General Product Information - (Show below) - (Hide below)

    Committee G-12ADF
    Development Note Supersedes MIL A 8243. (06/2004) Supersedes SAE AS 8243. (04/2010) Supersedes SAE AMS 1425. (06/2010) Supersedes SAE AMS 1427. (07/2010)
    Document Type Standard
    Publisher SAE International
    Status Superseded
    Superseded By
    Supersedes

    Standards Referencing This Book - (Show below) - (Hide below)

    ANSI Z400.1/Z129.1 : 2010 HAZARDOUS WORKPLACE CHEMICALS - HAZARD EVALUATION AND SAFETY DATA SHEET AND PRECAUTIONARY LABELING PREPARATION
    SAE AMS 4049 : 2016 ALUMINUM ALLOY, SHEET AND PLATE, ALCLAD 5.6ZN - 2.5MG - 1.6CU - 0.23CR (ALCLAD 7075; -T6 SHEET - T651 PLATE) SOLUTION AND PRECIPITATION HEAT TREATED
    SAE AMS 2475H : 2009 PROTECTIVE TREATMENTS, MAGNESIUM ALLOYS
    ASTM D 1177 : 2017 : REDLINE Standard Test Method for Freezing Point of Aqueous Engine Coolants
    SAE AMS 5886 : 2014 ALLOY, CORROSION AND HEAT-RESISTANT, BARS, FORGINGS, AND RINGS 50NI - 20CR - 20CO - 5.8MO - 2.2TI - 0.45AL CONSUMABLE ELECTRODE OR VACUUM INDUCTION MELTED 2100 DEGREES F (1149 DEGREES C) SOLUTION HEAT TREATED
    SAE AMS 4911 : 2014 TITANIUM ALLOY, SHEET, STRIP, AND PLATE, 6AL - 4 V, ANNEALED
    SAE AMS 4376 : 2011(R2018) PLATE, MAGNESIUM ALLOY - 3.0AL - 1.0ZN - 0.20MN (AZ31B-H26) COLD ROLLED AND PARTIALLY ANNEALED
    SAE AMS 4037 : 2014 ALUMINUM ALLOY, SHEET AND PLATE, 4.4CU - 1.5MG - 0.60MN (2024; -T3 FLAT SHEET, -T351 PLATE) SOLUTION HEAT TREATED
    SAE AIR 5567A : 2015 TEST METHOD FOR CATALYTIC CARBON BRAKE DISK OXIDATION
    CFR 40(PTS790-999) : JUL 2017 PROTECTION OF ENVIRONMENT - ENVIRONMENTAL PROTECTION AGENCY
    MIL STD 870 : C CADMIUM PLATING, LOW EMBRITTLEMENT, ELECTRODEPOSITION
    ASTM D 1331 : 2014 : REDLINE Standard Test Methods for Surface and Interfacial Tension of Solutions of Paints, Solvents, Solutions of Surface-Active Agents, and Related Materials
    SAE AMS P 83310 : 2016 PLASTIC SHEET, POLYCARBONATE, TRANSPARENT
    SAE AS 5900 : 2016 STANDARD TEST METHOD FOR AERODYNAMIC ACCEPTANCE OF AMS1424 AND AMS1428 AIRCRAFT DEICING/ANTI-ICING FLUIDS
    SAE ARP 1917 : 2002 CLARIFICATION OF TERMS USED IN AEROSPACE METALS SPECIFICATIONS
    SAE AS 6285 : 2016 AIRCRAFT GROUND DEICING/ANTI-ICING PROCESSES
    SAE AMS 1424/1 : 2016 DEICING/ANTI-ICING FLUID, AIRCRAFT SAE TYPE 1 GLYCOL (CONVENTIONAL AND NON-CONVENTIONAL) BASED
    ASTM D 93 : 2016-07 TEST METHODS FOR FLASH POINT BY PENSKY-MARTENS CLOSED CUP TESTER
    MIL PRF 25690 : B PLASTIC, SHEET AND FORMED PARTS, MODIFIED ACRYLIC BASE, MONOLITHIC, CRACK PROPAGATION RESISTANT
    SAE AMS 4916 : 2014 TITANIUM ALLOY SHEET, STRIP, AND PLATE 8AL - 1MO - 1V DUPLEX ANNEALED
    CFR 40(PTS136-149) : JUL 2017 PROTECTION OF ENVIRONMENT - ENVIRONMENTAL PROTECTION AGENCY
    SAE AS 5901 : 2014 WATER SPRAY AND HIGH HUMIDITY ENDURANCE TEST METHODS FOR SAE AMS1424 AND SAE AMS1428 AIRCRAFT DEICING/ANTI-ICING FLUIDS
    SAE AMS 2470 : 2013 ANODIC TREATMENT OF ALUMINUM ALLOYS, CHROMIC ACID PROCESS
    SAE AMS 1424/2 : 2016 DEICING/ANTI-ICING FLUID, AIRCRAFT SAE TYPE 1 NON-GLYCOL BASED
    SAE AMS 5045 : 2015 STEEL, SHEET AND STRIP, 0.25 CARBON, MAXIMUM HARD TEMPER
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective