We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
  • AS/NZS 61347.2.1:2002

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    Add to Watchlist
    This Standard has been added successfully to your Watchlist
    Please visit My Watchlist to see all standards that you are watching.
    Please log in or to add this standard to your Watchlist.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    You have already added this standard to your Watchlist.
    Visit My Watchlist to view the full list.

    Lamp controlgear Particular requirements for starting devices (other than glow starters)

    Available format(s):  Hardcopy, PDF 1 User, PDF 3 Users, PDF 5 Users, PDF 9 Users

    Superseded date:  20-02-2019

    Language(s):  English

    Published date:  10-10-2002

    Publisher:  Standards Australia

    Add to Watchlist

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Introduction1 Scope2 Normative references3 Definitions4 General requirements5 General notes on tests 5.1 Starting devices for use with lamps having different electrical characteristics 5.2 Number of specimens6 Classification7 Marking 7.1 Mandatory markings 7.2 Information to be provided, if applicable8 Protection against accidental contact with live parts9 Terminals10 Provisions for earthing11 Moisture resistance and insulation12 Electric strength13 Thermal endurance test for windings14 Fault conditions15 Heating of independent starting devices 15.1 Normal operation 15.2 Abnormal operation16 Pulse voltage of ignitors17 Mechanical strength18 Construction19 Creepage distances and clearances20 Screws, current-carrying parts and connections21 Resistance to heat, fire and tracking22 Resistance to corrosionAnnex A (normative) - Test to establish whether a conductive part is a live part which may cause an electric shockAnnex B (normative) - Particular requirements for thermally protected lamp controlgearAnnex C (normative) - Particular requirements for electronic lamp controlgear with means of protection against overheatingAnnex D (normative) - Requirements for carrying out the heating tests of thermally protected lamp controlgearAnnex E (normative) - Use of constant S other than 4500 in t[w] testsAnnex F (normative) - Draught-proof enclosureAnnex G (informative) - Explanation of the derivation of the values of pulse voltagesAnnex H (normative) - TestsAnnex I (normative) - Mechanical strength testingAnnex J (normative) - Precautions to be observed when measuring with sphere-gapsBibliography

    Abstract - (Show below) - (Hide below)

    Specifies safety requirements for starting devices for fluorescent and other discharge lamps for use on a.c. supplies up to 1000 volt at 50/60 Hz in combination with lamps and ballasts. This Standard is identical to and reproduced from IEC 61347-2-1:2000.

    Scope - (Show below) - (Hide below)

    This part of IEC 61347 AS/NZS 61347 specifies particular safety requirements for starting devices (starters other than glow starters and ignitors) for fluorescent and other discharge lamps for use on a.c. supplies up to 1 000 V at 50 Hz or 60 Hz which produce starting pulses not greater than 100 kV and which are used in combination with lamps and ballasts covered in IEC 60081, IEC 60188, IEC 60192, IEC 60662, IEC 60901, IEC 61167, IEC 61195, IEC 61199, IEC 61347-2-8 and IEC 61347-2-9.It does not apply to glow starters or starting devices which are incorporated in discharge lamps or which are manually operated. Preheat transformers for fluorescent lamps are covered by IEC 61347.2.8NOTE - Glow starters are dealt with in IEC 60155.This standard refers only to starting devices for use with ballasts and lamps which are internationally the most in demand.Performance requirements are given in IEC 60927.

    General Product Information - (Show below) - (Hide below)

    Committee EL-041
    Document Type Standard
    Publisher Standards Australia
    Status Superseded
    Superseded By
    Supersedes
    Under Revision

    History - (Show below) - (Hide below)

    First published as AS/NZS 61347.2.1:2002.

    Standards Referenced By This Book - (Show below) - (Hide below)

    AS 2886-1986 Voltage measurement - Sphere-gap method (one sphere earthed)
    AS 3864-1997 Medical refrigeration equipment - For the storage of blood and blood products
    AS 4111-1993 Starters for fluorescent lamps - Performance requirements
    AS/NZS 61347.1:2002 Lamp controlgear General and safety requirements (IEC 61347-1:2000, MOD)

    Standards Referencing This Book - (Show below) - (Hide below)

    AS/NZS 1158.6:2010 Lighting for roads and public spaces Luminaires
    AS/NZS IEC 61347.2.13:2013 Lamp controlgear Particular requirements for d.c. or a.c. supplied electronic controlgear for LED modules (IEC 61347-2-13, Ed.1.0 (2006) MOD)
    AS/NZS 61347.2.9:2004 Lamp controlgear Particular requirements for ballasts for discharge lamps (excluding fluorescent lamps) (IEC 61347-2-9:2000 MOD)
    AS/NZS 60927:2005 Auxiliaries for lamps - Starting devices (other than glow starters) - Performance requirements (IEC 60927, Ed.2.2 (2004) MOD)
    AS/NZS 60079.15:2006 Electrical apparatus for explosive gas atmospheres Construction, test and marking of type of protection, n electrical apparatus
    AS/NZS 60079.15:2011 Explosive atmospheres Equipment protection by type of protection ‘n’
    AS/NZS 1158.6:2004 Lighting for roads and public spaces Luminaires
    AS/NZS 60598.1:2003 Luminaires General requirements and tests (IEC 60598-1:2003, MOD)
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective