We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
  • BS EN 14154-1 : 2005

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    Add to Watchlist
    This Standard has been added successfully to your Watchlist
    Please visit My Watchlist to see all standards that you are watching.
    Please log in or to add this standard to your Watchlist.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    You have already added this standard to your Watchlist.
    Visit My Watchlist to view the full list.

    WATER METERS - PART 1: GENERAL REQUIREMENTS

    Available format(s):  Hardcopy, PDF

    Superseded date:  30-06-2014

    Language(s):  English

    Published date:  01-01-2005

    Publisher:  British Standards Institution

    Add to Watchlist

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Foreword
    1 Scope
    2 Normative references
    3 Terms and definitions
    4 Technical characteristics
    5 Meter classification
    6 Marking
    7 Metrological characteristics
    8 Meter performance requirements
    9 Metrological control
    Annex A (normative) - Checking facilities
    Annex B (normative) - In-line meter dimensions
            (including alternative lengths)
    Annex C (informative) - Table of rated operating,
            limiting and references conditions
    Annex D (informative) - Test program
    Annex ZA (informative) - Relationship between this
             European Standard and the Essential
             Requirements of EU Directive 22/2004/EC
             on Measuring Instruments
    Bibliography

    Abstract - (Show below) - (Hide below)

    Pertains to water meters intended for residential, commercial, light industrial and industrial use, and specifies the requirements and certification procedures for water meters, irrespective of the design technologies used to meter the actual volume of clean cold potable water or heated water, flowing through a fully charged, closed conduit.

    General Product Information - (Show below) - (Hide below)

    Committee CPI/30/7/1
    Development Note Supersedes BS 5728-7(1997), BS ISO 7858-1, BS 5728-2:SUPP1(1984) and 01/122224 DC. (06/2005) 2005 Edition Re-Issued in July 2011 & incorporates AMD 2 2011. (07/2011)
    Document Type Standard
    Publisher British Standards Institution
    Status Superseded
    Superseded By
    Supersedes

    Standards Referenced By This Book - (Show below) - (Hide below)

    17/30352105 DC : 0 BS 8614 - WATER METERS - ADDITIONAL REQUIREMENTS FOR METERS WITH POLYMER MAIN CASINGS

    Standards Referencing This Book - (Show below) - (Hide below)

    ISO 7005-2:1988 Metallic flanges Part 2: Cast iron flanges
    2004/22/EC : 2004 DIRECTIVE 2004/22/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL OF 31 MARCH 2004 ON MEASURING INSTRUMENTS
    ISO 7005-3:1988 Metallic flanges Part 3: Copper alloy and composite flanges
    ISO 3:1973 Preferred numbers Series of preferred numbers
    EN ISO 6708 : 1995 PIPEWORK COMPONENTS - DEFINITION AND SELECTION OF DN (NOMINAL SIZE)
    EN ISO 228-1 : 2003 PIPE THREADS WHERE PRESSURE-TIGHT JOINTS ARE NOT MADE ON THE THREADS - PART 1: DIMENSIONS, TOLERANCES AND DESIGNATION
    ISO/IEC Guide 99:2007 International vocabulary of metrology Basic and general concepts and associated terms (VIM)
    EN 14154-3:2005+A2:2011 WATER METERS - PART 3: TEST METHODS AND EQUIPMENT
    EN 14154-2:2005+A2:2011 WATER METERS - PART 2: INSTALLATION AND CONDITIONS OF USE
    EN 1333:2006 (edition 2) Flanges and their joints - Pipework components - Definition and selection of PN
    OIML R 49-1 : 2013 WATER METERS FOR COLD POTABLE WATER AND HOT WATER - PART 1: METROLOGICAL AND TECHNICAL REQUIREMENTS
    OIML R 49-2 : 2013 WATER METERS FOR COLD POTABLE WATER AND HOT WATER - PART 2: TEST METHODS
    ENV 13005 : DRAFT 1999 GUIDE TO THE EXPRESSION OF UNCERTAINTY IN MEASUREMENT
    ISO 7858-1:1998 Measurement of water flow in closed conduits Combination meters for cold potable water Part 1: Specifications
    ISO 6807:2003 Rubber hoses and hose assemblies for rotary drilling and vibration applications Specification
    ISO 228-1:2000 Pipe threads where pressure-tight joints are not made on the threads Part 1: Dimensions, tolerances and designation
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective