EN 13369:2018
Withdrawn
A Withdrawn Standard is one, which is removed from sale, and its unique number can no longer be used. The Standard can be withdrawn and not replaced, or it can be withdrawn and replaced by a Standard with a different number.
Common rules for precast concrete products
30-04-2021
11-04-2018
European foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Requirements
5 Test methods
6 Assessment and verification of constancy of performance
7 Marking
8 Technical documentation
Annex A (informative) - Concrete cover as regard to corrosion
Annex B (informative) - Concrete quality control
Annex C (informative) - Reliability considerations
Annex D (normative) - Inspection schemes
Annex E (informative) - Assessment of compliance
Annex F (normative) - Test of water absorption
Annex G (informative) - Shape correlation factor
for cores
Annex H (informative) - Measurement of dimensions
Annex I (informative) - Prestressing losses
Annex J (informative) - Technical documentation
Annex K (informative) - Properties of indented
bars and wire
Annex L (informative) - Resistance to fire: recommendations
for the use of EN 1992-1-2
Annex M (informative) - Survey of type testing
Annex N (informative) - Use of reclaimed crushed and
recycled coarse aggregates in concrete
Bibliography
This document specifies the requirements, the basic performance criteria and the Assessment and Verification of Constancy of Performance (AVCP) for unreinforced, reinforced and prestressed precast concrete products made of compact light-, normal- and heavyweight concrete according to EN 206 with no appreciable amount of entrapped air other than entrained air. Concrete containing fibres for other than mechanical properties (steel, polymer or other fibres) is also covered. It does not cover prefabricated reinforced components of lightweight aggregate concrete with open structure.It may also be used to specify products for which there is no standard. Not all of the requirements (Clause 4) of this standard are relevant to all precast concrete products.If a specific product standard exists, it takes precedence over this document.The precast concrete products dealt with in this standard are factory produced for building and civil engineering works. This document can also be applied to products manufactured in temporary plants on site if the production is protected against adverse weather conditions and controlled following Clause 6 provisions.The analysis and design of precast concrete products is not within the scope of this document but it does offer, for non-seismic zones, information about:-the choice of partial safety factors defined by the pertinent Eurocode;-the definition of some requirements for prestressed concrete products.
| Committee |
CEN/TC 229
|
| DevelopmentNote |
Supersedes PREN 13369. (04/2018)
|
| DocumentType |
Standard
|
| PublisherName |
Comite Europeen de Normalisation
|
| Status |
Withdrawn
|
| Supersedes |
| Standards | Relationship |
| DS/EN 13369:2018 | Identical |
| DS EN 13369 : 2013 | Identical |
| NS EN 13369 : 2013 | Identical |
| NBN EN 13369 : 2013 | Identical |
| DIN EN 13369:2018-09 | Identical |
| DIN EN 13369:2013-08 | Identical |
| NEN EN 13369 : 2018 | Identical |
| NS EN 13369:2018 | Identical |
| UNI EN 13369:2018 | Identical |
| UNI EN 13369 : 2013 | Identical |
| I.S. EN 13369:2013 | Identical |
| UNE-EN 13369:2018 | Identical |
| ONORM EN 13369: 2018 | Identical |
| UNE-EN 13369:2013 | Identical |
| NF EN 13369 : 2013 | Identical |
| BS EN 13369:2013 | Identical |
| ONORM EN 13369 : 2013 | Identical |
| SN EN 13369 : 2013 | Identical |
| PN EN 13369 : 2013 | Identical |
| NF EN 13369 : 2018 | Identical |
| BS EN 13369:2018 | Identical |
| I.S. EN 13369:2018 | Identical |
| EN 12390-3:2009/AC:2011 | TESTING HARDENED CONCRETE - PART 3: COMPRESSIVE STRENGTH OF TEST SPECIMENS |
| ISO 3951-1:2013 | Sampling procedures for inspection by variables — Part 1: Specification for single sampling plans indexed by acceptance quality limit (AQL) for lot-by-lot inspection for a single quality characteristic and a single AQL |
| EN ISO 10456:2007/AC:2009 | BUILDING MATERIALS AND PRODUCTS - HYGROTHERMAL PROPERTIES - TABULATED DESIGN VALUES AND PROCEDURES FOR DETERMINING DECLARED AND DESIGN THERMAL VALUES |
| CEN/TR 15728:2016 | Design and use of inserts for lifting and handling of precast concrete elements |
| ISO 717-2:2013 | Acoustics Rating of sound insulation in buildings and of building elements Part 2: Impact sound insulation |
| ISO 7873:1993 | Control charts for arithmetic average with warning limits |
| EN 12390-7:2009 | Testing hardened concrete - Part 7: Density of hardened concrete |
| EN 1934:1998 | Thermal performance of buildings - Determination of thermal resistance by hot box method using heat flow meter - Masonry |
| EN ISO 717-2:2013 | Acoustics - Rating of sound insulation in buildings and of building elements - Part 2: Impact sound insulation (ISO 717-2:2013) |
| CEN/TR 15739:2008 | Precast concrete products - Concrete finishes - Identification |
| EN ISO 8990:1996 | Thermal insulation - Determination of steady-state thermal transmission properties - Calibrated and guarded hot box (ISO 8990:1994) |
| EN 1745:2012 | Masonry and masonry products - Methods for determining thermal properties |
| EN 13501-2:2016 | Fire classification of construction products and building elements - Part 2: Classification using data from fire resistance tests, excluding ventilation services |
| EN 10080:2005 | Steel for the reinforcement of concrete - Weldable reinforcing steel - General |
| EN 1008:2002 | Mixing water for concrete - Specification for sampling, testing and assessing the suitability of water, including water recovered from processes in the concrete industry, as mixing water for concrete |
| EN 12504-2:2012 | TESTING CONCRETE IN STRUCTURES - PART 2: NON-DESTRUCTIVE TESTING - DETERMINATION OF REBOUND NUMBER |
| EN ISO 6946:2017 | Building components and building elements - Thermal resistance and thermal transmittance - Calculation methods (ISO 6946:2017, Corrected version 2021-12) |
| EN 12354-1:2000 | Building Acoustics - Estimation of acoustic performance of buildings from the performance of elements - Part 1: Airborne sound insulation between rooms |
| ASTM C 173/C173M : 2016 : REDLINE | Standard Test Method for Air Content of Freshly Mixed Concrete by the Volumetric Method |
| EN ISO 9001:2015 | Quality management systems - Requirements (ISO 9001:2015) |
| EN 12620:2002+A1:2008 | Aggregates for concrete |
| EN 12664:2001 | Thermal performance of building materials and products - Determination of thermal resistance by means of guarded hot plate and heat flow meter methods - Dry and moist products of medium and low thermal resistance |
| EN 12390-1:2012 | TESTING HARDENED CONCRETE - PART 1: SHAPE, DIMENSIONS AND OTHER REQUIREMENTS FOR SPECIMENS AND MOULDS |
| EN 1992-1-2:2004/AC:2008 | EUROCODE 2: DESIGN OF CONCRETE STRUCTURES - PART 1-2: GENERAL RULES - STRUCTURAL FIRE DESIGN |
| EN 12390-2:2009 | Testing hardened concrete - Part 2: Making and curing specimens for strength tests |
| ISO 10456:2007 | Building materials and products — Hygrothermal properties — Tabulated design values and procedures for determining declared and design thermal values |
| ISO 9001:2015 | Quality management systems — Requirements |
| ISO 7870-4:2011 | Control charts Part 4: Cumulative sum charts |
| EN 16192:2011 | Characterization of waste - Analysis of eluates |
| ISO 7976-1:1989 | Tolerances for building — Methods of measurement of buildings and building products — Part 1: Methods and instruments |
| ISO 717-1:2013 | Acoustics Rating of sound insulation in buildings and of building elements Part 1: Airborne sound insulation |
| EN 1097-6:2013 | Tests for mechanical and physical properties of aggregates - Part 6: Determination of particle density and water absorption |
| EN 12390-6:2009 | Testing hardened concrete - Part 6: Tensile splitting strength of test specimens |
| EN 1992-1-1:2004/A1:2014 | EUROCODE 2: DESIGN OF CONCRETE STRUCTURES - PART 1-1: GENERAL RULES AND RULES FOR BUILDINGS |
| EN 12350-7:2009 | Testing fresh concrete - Part 7: Air content - Pressure methods |
| ISO 6946:2017 | Building components and building elements — Thermal resistance and thermal transmittance — Calculation methods |
| EN 12504-1:2009 | Testing concrete in structures - Part 1: Cored specimens - Taking, examining and testing in compression |
| EN 1990:2002/A1:2005/AC:2010 | EUROCODE - BASIS OF STRUCTURAL DESIGN |
| ISO 8990:1994 | Thermal insulation — Determination of steady-state thermal transmission properties — Calibrated and guarded hot box |
| ISO 1803:1997 | Building construction Tolerances Expression of dimensional accuracy Principles and terminology |
| EN 13670:2009 | Execution of concrete structures |
| EN 206:2013+A1:2016 | Concrete - Specification, performance, production and conformity |
| CEN/TR 16563:2013 | Principles of the equivalent durability procedure |
| EN 12354-2:2000 | Building acoustics - Estimation of acoustic performance of buildings from the performance of elements - Part 2: Impact sound insulation between rooms |
| EN 934-2:2009+A1:2012 | Admixtures for concrete, mortar and grout - Part 2: Concrete admixtures - Definitions, requirements, conformity, marking and labelling |
| EN 13791:2007 | Assessment of in-situ compressive strength in structures and precast concrete components |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.