We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
  • BS EN 10218-1:2012 (published 2012-01)

    Current The latest, up-to-date edition.
    Add to Watchlist
    This Standard has been added successfully to your Watchlist
    Please visit My Watchlist to see all standards that you are watching.
    Please log in or to add this standard to your Watchlist.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    You have already added this standard to your Watchlist.
    Visit My Watchlist to view the full list.

    Steel wire and wire products. General Test methods

    Available format(s):  Hardcopy, PDF

    Language(s):  English

    Published date:  31-01-2012

    Publisher:  British Standards Institution

    Add to Watchlist

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Foreword
    1 Scope
    2 Normative references
    3 Tensile test
    4 Simple torsion test
    5 Reverse bend test
    6 Wrapping test
    7 Bend test
    8 Reverse torsion test
    9 Compression test
    10 Deep etch test
    11 Hardness test
    12 Quench hardenability test
    13 Fatigue test (bend and axial)
    14 Wire cast measurement
    15 Artificial ageing
    16 Decarburization test
    17 Non-destructive tests
    18 Grain size test
    19 Segregation test
    20 Non-metallic inclusion test
    21 Chemical analysis
    22 Retests

    Abstract - (Show below) - (Hide below)

    Describes the methods for the general testing of steel wire and wire products which have been cold worked, annealed or oil hardened and tempered and/or coated and are of constant cross section, either round, or special section.

    General Product Information - (Show below) - (Hide below)

    Committee ISE/106
    Development Note Supersedes BS 4545(1970) and 91/47200 DC. (07/2005) Supersedes 08/30180859 DC. (01/2012)
    Document Type Standard
    Publisher British Standards Institution
    Status Current
    Supersedes

    Standards Referenced By This Book - (Show below) - (Hide below)

    BS 8002:2015 CODE OF PRACTICE FOR EARTH RETAINING STRUCTURES
    BS 6S100(2010) : 2010 AEROSPACE SERIES - PROCEDURE FOR INSPECTION, TESTING AND ACCEPTANCE OF WROUGHT STEELS (OTHER THAN PLATE, SHEET, STRIP AND TUBE)
    09/30093195 DC : 0 BS 6349-2 - MARITIME WORKS - PART 2: CODE OF PRACTICE FOR THE DESIGN OF QUAY WALLS, JETTIES AND DOLPHINS
    09/30199785 DC : 0 BS 6S 100 - PROCEDURE FOR INSPECTION, TESTING AND ACCEPTANCE OF WROUGHT STEELS (OTHER THAN PLATE, SHEET, STRIP AND TUBE)

    Standards Referencing This Book - (Show below) - (Hide below)

    EN 10247:2017 Micrographic examination of the non-metallic inclusion content of steels using standard pictures
    EN ISO 6508-1:2016 METALLIC MATERIALS - ROCKWELL HARDNESS TEST - PART 1: TEST METHOD (ISO 6508-1:2016)
    EN ISO 6506-1:2014 METALLIC MATERIALS - BRINELL HARDNESS TEST - PART 1: TEST METHOD (ISO 6506-1:2014)
    ISO 6506-1:2014 Metallic materials Brinell hardness test Part 1: Test method
    CEN/TR 10261 : 2013 IRON AND STEEL - EUROPEAN STANDARDS FOR THE DETERMINATION OF CHEMICAL COMPOSITION
    EN ISO 6892-1:2016 METALLIC MATERIALS - TENSILE TESTING - PART 1: METHOD OF TEST AT ROOM TEMPERATURE (ISO 6892-1:2016)
    EN ISO 16120-1:2017 NON-ALLOY STEEL WIRE ROD FOR CONVERSION TO WIRE - PART 1: GENERAL REQUIREMENTS (ISO 16120-1:2017)
    ISO 6508-3:2015 Metallic materials Rockwell hardness test Part 3: Calibration of reference blocks
    EN ISO 377:2017 STEEL AND STEEL PRODUCTS - LOCATION AND PREPARATION OF SAMPLES AND TEST PIECES FOR MECHANICAL TESTING (ISO 377:2017)
    EN ISO 643:2012 STEELS - MICROGRAPHIC DETERMINATION OF THE APPARENT GRAIN SIZE (ISO 643:2012)
    ISO 6508-1:2016 Metallic materials Rockwell hardness test Part 1: Test method
    ISO 9649:2016 Metallic materials Wire Reverse torsion test
    ISO 6508-2:2015 Metallic materials Rockwell hardness test Part 2: Verification and calibration of testing machines and indenters
    ISO 3887:2003 Steels Determination of depth of decarburization
    EN 10021:2006 General technical delivery conditions for steel products
    EN ISO 6892-2 : 2011 METALLIC MATERIALS - TENSILE TESTING - PART 2: METHOD OF TEST AT ELEVATED TEMPERATURE
    ISO 643:2012 Steels Micrographic determination of the apparent grain size
    ISO 7802:2013 Metallic materials Wire Wrapping test
    ISO 7801:1984 Metallic materials Wire Reverse bend test
    EN ISO 6508-3:2015 METALLIC MATERIALS - ROCKWELL HARDNESS TEST - PART 3 - CALIBRATION OF REFERENCE BLOCKS (ISO 6508-3:2015)
    ISO 377:2017 Steel and steel products — Location and preparation of samples and test pieces for mechanical testing
    ISO 7800:2012 Metallic materials — Wire — Simple torsion test
    EN ISO 6508-2:2015 METALLIC MATERIALS - ROCKWELL HARDNESS TEST - PART 2: VERIFICATION AND CALIBRATION OF TESTING MACHINES AND INDENTERS (ISO 6508-2:2015)
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective