Customer Support: +44 (0)203 327 3140

Login to i2i Subscription Intertek.com
  • There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Go to AMERICAS site
Dismiss alert
Please enter a keyword to search
Advanced search
Home
ASTM
ASTM D 8291 : 2021 : REV A : EDT 1

ASTM D 8291 : 2021 : REV A : EDT 1

Superseded

Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Test Method for Evaluation of Performance of Automotive Engine Oils in the Mitigation of Low-Speed, Preignition in the Sequence IX Gasoline Turbocharged Direct-Injection, Spark-Ignition Engine

Available format(s)

Hardcopy , PDF

Superseded date

08-11-2023

Language(s)

English

Published date

27-06-2022

Publisher

American Society for Testing and Materials

1.1This laboratory engine test evaluates the ability of an automotive engine to mitigate preignition in the combustion chambers in gasoline, turbocharged, direct-injection (GTDI) engines under low-speed and high-load operating conditions. This test method is commonly known as the Ford low-speed, preignition (LSPI) test.

1.1.1In vehicles, equipped with relatively small GTDI spark-ignition engines, preignition has occasionally occurred when the vehicles are operated under low-speed and high-load conditions. Uncontrolled, preignition may cause destructive engine damage.

1.2The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

1.2.1Exceptions—Where there is no direct SI equivalent such as screw threads, national pipe threads/diameters, tubing size, wire gauge, or specified single source equipment.

1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Committee
D 02
DocumentType
Test Method
Pages
57
ProductNote
ε1NOTE—Editorially updated TMC governance information in June 2022.
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

ASTM D 8279 : 2023 Standard Test Method for Determination of Timing-Chain Wear in a Turbocharged, Direct-Injection, Spark-Ignition, Four-Cylinder Engine
ASTM D 4485 : 2020 Standard Specification for Performance of Active API Service Category Engine Oils

ASTM D 8047 : 2023 Standard Test Method for Evaluation of Engine Oil Aeration Resistance in a Caterpillar C13 Direct-Injected Turbocharged Automotive Diesel Engine
ASTM D 8047 : 2019 : EDT 1 Standard Test Method for Evaluation of Engine Oil Aeration Resistance in a Caterpillar C13 Direct-Injected Turbocharged Automotive Diesel Engine
ASTM D 86 : 2023 Standard Test Method for Distillation of Petroleum Products and Liquid Fuels at Atmospheric Pressure
ASTM D 1319 : 2018 Standard Test Method for Hydrocarbon Types in Liquid Petroleum Products by Fluorescent Indicator Adsorption
ASTM D 86 : 2020 : REV A Standard Test Method for Distillation of Petroleum Products and Liquid Fuels at Atmospheric Pressure
ASTM D 1298 : 2012 : REV B : R2017 : EDT 1 Standard Test Method for Density, Relative Density, or API Gravity of Crude Petroleum and Liquid Petroleum Products by Hydrometer Method
ASTM D 2699 : 2022 Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel
ASTM D 86 : 2018 Standard Test Method for Distillation of Petroleum Products and Liquid Fuels at Atmospheric Pressure
ASTM D 1298 : 2012 : REV B : R2017 Standard Test Method for Density, Relative Density, or API Gravity of Crude Petroleum and Liquid Petroleum Products by Hydrometer Method
ASTM D 445 : 2021 : EDT 2 Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity)
ASTM D 2700 : 2022 Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel
ASTM D 2699 : 2023 Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel
ASTM D 445 : 2017 : REV A Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity)
ASTM D 86 : 2019 Standard Test Method for Distillation of Petroleum Products and Liquid Fuels at Atmospheric Pressure
ASTM D 2709 : 2016 Standard Test Method for Water and Sediment in Middle Distillate Fuels by Centrifuge
ASTM D 2700 : 2022 : REV B Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel
ASTM D 86 : 2012 Standard Test Method for Distillation of Petroleum Products at Atmospheric Pressure
ASTM D 4485 : 2020 Standard Specification for Performance of Active API Service Category Engine Oils
ASTM D 2699 : 2022 : REV A Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel
ASTM D 2699 : 2019 : EDT 1 Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel
ASTM D 86 : 2020 : REV B Standard Test Method for Distillation of Petroleum Products and Liquid Fuels at Atmospheric Pressure
ASTM D 86 : 2016 : REV A Standard Test Method for Distillation of Petroleum Products and Liquid Fuels at Atmospheric Pressure
ASTM D 445 : 2019 : REV A Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity)
ASTM D 5453 : 2016 : EDT 1 Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Spark Ignition Engine Fuel, Diesel Engine Fuel, and Engine Oil by Ultraviolet Fluorescence
ASTM D 445 : 2019 Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity)
ASTM D 381 : 2019 Standard Test Method for Gum Content in Fuels by Jet Evaporation
ASTM D 2709 : 2022 Standard Test Method for Water and Sediment in Middle Distillate Fuels by Centrifuge
ASTM D 130 : 2018 Standard Test Method for Corrosiveness to Copper from Petroleum Products by Copper Strip Test
ASTM D 381 : 2022 Standard Test Method for Gum Content in Fuels by Jet Evaporation
ASTM D 2699 : 2021 Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel
ASTM D 2622 : 2021 Standard Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-ray Fluorescence Spectrometry
ASTM D 445 : 2021 Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity)
ASTM D 381 : 2012 : R2017 Standard Test Method for Gum Content in Fuels by Jet Evaporation
ASTM D 86 : 2020 Standard Test Method for Distillation of Petroleum Products and Liquid Fuels at Atmospheric Pressure
ASTM D 2700 : 2022 : REV A Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel
ASTM D 4485 : 2022 Standard Specification for Performance of Active API Service Category Engine Oils
ASTM D 3237 : 2017 Standard Test Method for Lead in Gasoline by Atomic Absorption Spectroscopy
ASTM D 5453 : 2019 Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Spark Ignition Engine Fuel, Diesel Engine Fuel, and Engine Oil by Ultraviolet Fluorescence
ASTM D 445 : 2018 Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity)
ASTM D 86 : 2015 Standard Test Method for Distillation of Petroleum Products and Liquid Fuels at Atmospheric Pressure
ASTM D 445 : 2021 : EDT 1 Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity)
ASTM D 3237 : 2022 Standard Test Method for Lead in Gasoline by Atomic Absorption Spectroscopy
ASTM D 86 : 2017 Standard Test Method for Distillation of Petroleum Products and Liquid Fuels at Atmospheric Pressure
ASTM D 2700 : 2023 Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel
ASTM D 1319 : 2019 Standard Test Method for Hydrocarbon Types in Liquid Petroleum Products by Fluorescent Indicator Adsorption
ASTM D 525 : 2012 : REV A Standard Test Method for Oxidation Stability of Gasoline (Induction Period Method)
ASTM D 2699 : 2019 Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel
ASTM D 130 : 2012 Standard Test Method for Corrosiveness to Copper from Petroleum Products by Copper Strip Test
ASTM D 4485 : 2022 : EDT 1 Standard Specification for Performance of Active API Service Category Engine Oils
ASTM D 2622 : 2016 Standard Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-ray Fluorescence Spectrometry

View more information
£97.67
Excluding VAT
GBP
CAD
CHF
CNY
DKK
EUR
GBP
HKD
IDR
INR
JPY
KRW
MXN
NOK
NZD
SEK
SGD
USD
ZAR
Hardcopy - English
PDF - English
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Learn more on subscription solutions

or

Get in touch with us