• There are no items in your cart

ASTM D 7277 : 2016

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Test Method for Performance Testing of Articulating Concrete Block (ACB) Revetment Systems for Hydraulic Stability in Open Channel Flow
Available format(s)

Hardcopy , PDF

Superseded date

08-12-2023

Language(s)

English

Published date

04-18-2016

1.1The purpose of this test method is to provide specifications for the hydraulic testing of full-scale articulating concrete block (ACB) revetment systems under controlled laboratory conditions for purposes of identifying stability performance in steep slope, high-velocity flows. The testing protocols, including system installation, test procedures, measurement techniques, analysis techniques, and reporting requirements are described in this test method.

1.2The values stated in inch-pound units are to be regarded as standard. The values given in brackets are mathematical conversions to SI units that are provided for information only and are not considered standard. Reporting or use of units other than inch-pound shall not be considered non-conformance as long as the selected parameters described regarding flume construction by the inch-pound system used in this method are met as a minimum.

1.2.1The gravitational system of inch-pound units is used when dealing with inch-pound units. In this system, the pound (lbf) represents a unit of force (weight), while the unit for mass is slugs. The rationalized slug unit is not given, unless dynamic (F = ma) calculations are involved.

1.3All observed and calculated values shall conform to the guidelines for significant digits and rounding established in Practice D6026.

1.3.1The procedures used to specify how data are collected, recorded and calculated in this Guide are regarded as the industry standard. In addition they are representative of the significant digits that generally be retained. The procedures used do not consider material variation, purpose of obtaining the data, special purpose studies or any considerations for the user’s objectives; and it is common practice to increase or reduce significant digits of reported data to be commensurate with these considerations. It is beyond the scope of this standard to consider significant digits used in analysis methods for engineering design.

1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Note 1:The quality of the result produced by this standard is dependent on the competence of the personnel performing it and the suitability of the equipment and facilities used. Agencies that meet criteria of Practice D3740 are generally considered capable of competent and objective testing. Users of this standard are cautioned that compliance with Practice D3740 does not in itself assure reliable results. Reliable results depend on many factors and Practice D3740 provides a means of evaluating some of these factors.

Committee
D 18
DocumentType
Test Method
Pages
7
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

ASTM D 7276 : 2016 Standard Guide for Analysis and Interpretation of Test Data for Articulating Concrete Block (ACB) Revetment Systems in Open Channel Flow

ASTM D 2216 : 2005 Standard Test Methods for Laboratory Determination of Water (Moisture) Content of Soil and Rock by Mass
ASTM D 2487 : 2017 : EDT 1 Standard Practice for Classification of Soils for Engineering Purposes (Unified Soil Classification System)
ASTM D 5195 : 2008 Standard Test Method for Density of Soil and Rock In-Place at Depths Below Surface by Nuclear Methods
ASTM D 653 : 2007 Standard Terminology Relating to Soil, Rock, and Contained Fluids
ASTM D 2216 : 2010 Standard Test Methods for Laboratory Determination of Water (Moisture) Content of Soil and Rock by Mass
ASTM D 3740 : 2012 Standard Practice for Minimum Requirements for Agencies Engaged in Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction
ASTM D 4318 : 2005 Standard Test Methods for Liquid Limit, Plastic Limit, and Plasticity Index of Soils
ASTM D 698 : 2000 Standard Test Methods for Laboratory Compaction Characteristics of Soil Using Standard Effort (12,400 ft-lbf/ft<sup>3</sup> (600 kN-m/m<sup>3</sup>))
ASTM D 422 : 1963 : R2007 : EDT 1 Standard Test Method for Particle-Size Analysis of Soils
ASTM D 1556 : 2007 Standard Test Method for Density and Unit Weight of Soil in Place by the Sand-Cone Method
ASTM D 3740 : 2019 Standard Practice for Minimum Requirements for Agencies Engaged in Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction
ASTM D 3740 : 2004 : REV A : EDT 1 Standard Practice for Minimum Requirements for Agencies Engaged in the Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction
ASTM D 1556 : 2000 Standard Test Method for Density and Unit Weight of Soil in Place by the Sand-Cone Method
ASTM D 3740 : 2008 Standard Practice for Minimum Requirements for Agencies Engaged in Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction
ASTM D 6026 : 2013 Standard Practice for Using Significant Digits in Geotechnical Data
ASTM D 698 : 2012 : R2021 Standard Test Methods for Laboratory Compaction Characteristics of Soil Using Standard Effort (12,400 ft-lbf/ft<sup>3</sup> (600 kN-m/m<sup>3</sup>))
ASTM D 5195 : 1991 : R1996 Standard Test Method for Density of Soil and Rock In-Place at Depths Below the Surface by Nuclear Methods
ASTM D 6026 : 2006 Standard Practice for Using Significant Digits in Geotechnical Data
ASTM D 4318 : 2010 Standard Test Methods for Liquid Limit, Plastic Limit, and Plasticity Index of Soils
ASTM D 5195 : 2021 Standard Test Method for Density of Soil and Rock In-Place at Depths Below Surface by Nuclear Methods
ASTM D 3740 : 1999 : REV C Standard Practice for Minimum Requirements for Agencies Engaged in the Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction
ASTM D 4318 : 2000 Standard Test Methods for Liquid Limit, Plastic Limit, and Plasticity Index of Soils
ASTM D 653 : 2022 Standard Terminology Relating to Soil, Rock, and Contained Fluids
ASTM D 653 : 2020 : EDT 1 Standard Terminology Relating to Soil, Rock, and Contained Fluids
ASTM D 6026 : 1999 Standard Practice for Using Significant Digits in Geotechnical Data
ASTM D 3740 : 2011 Standard Practice for Minimum Requirements for Agencies Engaged in Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction
ASTM D 6026 : 2001 : EDT 1 Standard Practice for Using Significant Digits in Geotechnical Data
ASTM D 3740 : 2010 Standard Practice for Minimum Requirements for Agencies Engaged in Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction
ASTM D 653 : 2021 : REV A Standard Terminology Relating to Soil, Rock, and Contained Fluids
ASTM D 2216 : 2019 Standard Test Methods for Laboratory Determination of Water (Moisture) Content of Soil and Rock by Mass
ASTM D 4318 : 2017 : EDT 1 Standard Test Methods for Liquid Limit, Plastic Limit, and Plasticity Index of Soils
ASTM D 6026 : 1996 Standard Practice for Using Significant Digits in Geotechnical Data
ASTM D 3740 : 2004 : REV A Standard Practice for Minimum Requirements for Agencies Engaged in the Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction
ASTM D 3740 : 2001 Standard Practice for Minimum Requirements for Agencies Engaged in the Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction
ASTM D 2487 : 2006 : EDT 1 Standard Practice for Classification of Soils for Engineering Purposes (Unified Soil Classification System)
ASTM D 653 : 2021 Standard Terminology Relating to Soil, Rock, and Contained Fluids
ASTM D 653 : 2021 : REV B Standard Terminology Relating to Soil, Rock, and Contained Fluids
ASTM D 4318 : 2010 : EDT 1 Standard Test Methods for Liquid Limit, Plastic Limit, and Plasticity Index of Soils
ASTM D 6026 : 1996 : EDT 1 Standard Practice for Using Significant Digits in Geotechnical Data
ASTM D 3740 : 2012 : REV A Standard Practice for Minimum Requirements for Agencies Engaged in Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction
ASTM D 4318 : 2017 Standard Test Methods for Liquid Limit, Plastic Limit, and Plasticity Index of Soils
ASTM D 3740 : 2003 Standard Practice for Minimum Requirements for Agencies Engaged in the Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction
ASTM D 2487 : 2010 Standard Practice for Classification of Soils for Engineering Purposes (Unified Soil Classification System)
ASTM D 2216 : 1998 Standard Test Method for Laboratory Determination of Water (Moisture) Content of Soil and Rock by Mass
ASTM D 2487 : 2000 Standard Classification of Soils for Engineering Purposes (Unified Soil Classification System)
ASTM D 2487 : 2006 Standard Practice for Classification of Soils for Engineering Purposes (Unified Soil Classification System)
ASTM D 6026 : 2021 Standard Practice for Using Significant Digits and Data Records in Geotechnical Data
ASTM D 2216 : 1971 Standard Method of Laboratory Determination Of Moisture Content Of Soil
ASTM D 5195 : 2014 Standard Test Method for Density of Soil and Rock In-Place at Depths Below Surface by Nuclear Methods
ASTM D 6026 : 2001 Standard Practice for Using Significant Digits in Geotechnical Data
ASTM D 2487 : 2011 Standard Practice for Classification of Soils for Engineering Purposes (Unified Soil Classification System)
ASTM D 2487 : 2017 Standard Practice for Classification of Soils for Engineering Purposes (Unified Soil Classification System)
ASTM D 5195 : 2014 : EDT 1 Standard Test Method for Density of Soil and Rock In-Place at Depths Below Surface by Nuclear Methods
ASTM D 3740 : 2004 Standard Practice for Minimum Requirements for Agencies Engaged in the Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction
ASTM D 2487 : 1969 : R1975 Standard Test Method for Classification Of Soils For Engineering Purposes
ASTM D 5195 : 2002 Standard Test Method for Density of Soil and Rock In-Place at Depths Below the Surface by Nuclear Methods
ASTM D 698 : 2012 : EDT 2 Standard Test Methods for Laboratory Compaction Characteristics of Soil Using Standard Effort (12 400 ft-lbf/ft<sup>3</sup> (600 kN-m/m<sup>3</sup>))

View more information
US$75.00
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.